Question about 2004 Ford Expedition

Open Question

How do I remove a stripped caliper bolt on a 2002 ford explorer

The rear caliper bolt is stripped can I remove the whole assembly?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 350 Answers

SOURCE: 2006 Ford Five Hundred anti-lock brake pad replacement

hi its rare the pads stick to the rotor but obviously this one was welded metal to metal so if the other sides not down to the metal you won,t have the same problem now getting the piston back into the caliper if you don,t have the tool its going to be fiddling but you need to get some pressure on the piston as to shove it back in not to much as you have stated it has to be screwed back in once a pressure has been applied [could try using you c-clamp ] then the slots in the piston insert something that will turn the piston it will locate and start to screw back your going to need pateince as it is fiddling with the correct tool you may need a few attemps but the other side should not be as bad as the piston has not gone past the point of return take your time and check for leaks when you have them all assembled yates210456

Posted on Oct 17, 2008

fknstart
  • 404 Answers

SOURCE: removal of rear brake drum 2002 ford escape

make sure handbrake is off take wheel off hit the drum with a mallet not steel,as it will brake,hit on outter diametter face of drum, try and rotate as you twist off

Posted on Jan 05, 2009

chuck943
  • 783 Answers

SOURCE: How do I remove the rear wiper arm on my 1996 Ford Explorer?

Pull the wiper arm away from the glass until it is straight out. Then take a small flat blade screw driver and release the retaining clip at the base of the pivot arm. The carefully pry the pivot arm from the shaft.

Posted on Apr 15, 2009

  • 166 Answers

SOURCE: 2002 Ford Explorer - Drivers side door lock, rear

Aside from the fuses, your drive side power door lock may be failing to work because of a bad door-lock relay system, or, alternatively, the locking switch/button, itself, is not malfunctioning and in need of replacement.

A great handyman site that specifies the above probable causes and more is the following link:
http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Vehicle_Car_Zone_Cars_Trucks_Vans_Locks_Power_Locks_Do_Not_Lock_When_Pressing_Locking_Switch_Button.htm

Good luck!

Posted on Jul 18, 2009

  • 2 Answers

SOURCE: How do you remove the inner door panel on the rear

carefully pry off door handle bezel from around door handle,thenpry out the front edge of armrest control plate and disconnect.then remove the lower trim panel retaining screws there will be one also up behind where control panel was.then grab trim panel at the switch opening and pull it up and out. hope the helps you.

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i find rear caliper carrier mounting bolts for peugeot 407


On the back side of the brakes, will be 2 bolts attached to steering knuckle. You have 2 ways to remove it. You can take the 2 bolts that hold the caliper onto the caliper mounting bracket, usually a rubber boot on them, then remove the caliper. At that point, you'll have easier access to the 2 remaining bolts that screw into the knuckle. The other option is just remove the whole assembly, remove the 2 bolts in the mounting bracket to remove the whole thing.

Mar 24, 2015 | Peugeot Cars & Trucks

1 Answer

What is the easiest way to remove the rear hub on a 2005 Ford Explorer?


ok here goes, I will try to remain as simple as possible/

remove the tire

locate the brake caliper, there are 2 slide bolts holding the caliper on (no need to remove them) but they are bolted into the caliper bracket. There is 2 bolts holding the caliper bracket on- remove those 2 bolts (be careful they will be pretty tight) the caliper/bracket assembly will then slide upwards off of the rotor

once you have the caliper and bracket assembly off of the rotor you need to support the caliper assembly ( I usually tie it up with a coat hanger or a piece of copper wire) make sure to tie the caliper up high or far off to the side to give yourself adequate work room.

The rotor will slide off of the hub really easy
On the back of the hub you will locate 3 bolts, usually one at the bottom and 2 on the top corners (picture a triangle)
when you remove those 3 bolts the hub is ready to be removed
given that your vehicle is an 05 I wouldn't think that the hub would be very hard to pull out, but you may need to coach it out a little
if you have to coach it out the best way to do that is to place the tire back onto the hub and put a couple of lug nuts back on. Then wiggle the tire from side to side until the hub comes off.

Nov 16, 2011 | Cars & Trucks

2 Answers

Rear pad removal?


Here ya go! This is for the rear brake pads removal:

Removal & Installation
  1. Remove the brake master cylinder filler cap. Check brake fluid level in brake master cylinder reservoir. Remove fluid until brake master cylinder reservoir is half full.
  2. Raise and support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Inspect the brake pads for wear or contamination. If worn, damaged or past specification, install new components.
  5. Remove the caliper pin bolts.
  6. Remove the rear disc brake caliper.
  7. Remove the brake pads and rail clips.
  8. Inspect the disc brake caliper for leaks. If leaks are found, disassembly is required.
  9. Installation is the reverse of removal. Observe the following torques:
    • Caliper bolts: 27 ft. lbs. (36 Nm)
  10. // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

May 12, 2011 | 2002 Ford E350

1 Answer

Remove rear brake disc


Remove the two bolts that hold the brake caliper on, remove the brake caliper, pull the brake rotor off. Opposite for assembly.

Feb 09, 2011 | 2002 Ford Explorer

1 Answer

Need to know how to get to the emergency brake on an 2002 ford explorer behind the disk brake.(rear driver side)


First remove caliper slider assembly & caliper. Will need to probably spray penetrating oil around rotor hub. Hit rotor on side of hub with sledge hammer & it will slide off. Inside are your emergency brake shoes.

Oct 20, 2010 | 2002 Ford Explorer

1 Answer

How do remove rear rotors on 2004 ford sport trac


Caliper removal

  1. Disconnect the brake hose.
  2. Remove the bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
--------------------------------------------------------------------------------------------
Disc Removal and Installation
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and retract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc. For additional information on machining brake discs, refer to Section 206-00 .
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
---------------------------------------------------------------------------------------------
Installation
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

Dec 17, 2009 | 2004 Ford Explorer Sport Trac

1 Answer

Change the brakes on 2007 sport trac


it has front and rear disc brakes, disc brakes are very simple to change out. Most disc brakes have two bolts that hold them on, one on the bottom one on the top on the inside of the brake caliper, they may be an allen head, or just a bolt. Remove them counter-clockwise. After you remove the two bolts, lift up and away on the caliper and the whole assembly will come off. Once you pull the assembly off you will see the two pads, one of them is driven by a piston, the other one is fixed. Remove the fixed one, they just pop off (have little metal clips you may have to slide the pad off). Take a C-clamp or something comparable to squeeze with, place it on the back of the caliper and on the old pad thereby squeezing the cylinder back into the piston, once you squeeze the cylinder back into the piston, it will give you room needed for thicker new brake pads. Piston should retract with the c-clamp fairly easy, shouldn't be a whole lot of resistance. Remove c-clamp after you get it to retract and remove old pad. Put new pad on, just like you took the old ones off. All four are basically the same to change out, they all have two bolts holding them on. You pull those, get the pistons to retract and replace the worn pads, put them back on, line up holes, put bolts back in... and your good to go. When you get back in the car and turn the key on, you may have to pump the brakes a few times.

Nov 01, 2009 | 2007 Ford Explorer Sport Trac

3 Answers

How do i remove the rear rotor on a 2000 ford explorer xlt


  1. Disconnect the brake hose.
  2. Remove bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  5. Disconnect the brake hose.
    1. Remove bolt.
    1. Disconnect the rear wheel brake hose (2A442).
    1. Remove the copper washers and plug the brake hose.
      syn~us~en~file=dh0472a.gif~gen~ref.gif
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
      Remove the rear disc brake caliper (2552).
      1. Remove the brake caliper bolts (2W303).
      1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
      syn~us~en~file=gh0619a.gif~gen~ref.gif
    1. Inspect the rear disc brake caliper for leaks.
      • If leaks are found, disassembly is required. Refer to Caliper in this section.
      syn~us~en~file=gh1478a.gif~gen~ref.gif
    Installation
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
      NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
      NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
      Install the rear disc brake caliper.
      syn~us~en~file=dh0528a.gif~gen~ref.gif
    1. Install the rear wheel brake hose.
      • Connect the brake hose and install the caliper flow bolt.
        • Use new copper washers.
      syn~us~en~file=gh0621a.gif~gen~ref.gif
    1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
    1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
      Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
    1. Verify correct brake operation.
  6. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
--------------------------------
Installation
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
    Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

May 06, 2009 | 2000 Ford Explorer

1 Answer

Bad right rear axle. Need to know how to replace axle.


Dana or Ford axle?

Ford here:
SECTION 205-05: Rear Drive Halfshafts 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Halfshaft
Special Tool(s) s2n~us~en~file=st2258a.gif~gen~ref.gif Protector, Differential Seal
205-506 s2n~us~en~file=st2272a.gif~gen~ref.gif Remover, Front Wheel Hub
205-D070 (D93P-1175-B) or equivalent s2n~us~en~file=st2309a.gif~gen~ref.gif Remover, Halfshaft
205-502
Removal and Installation
NOTE: This procedure applies to both rear halfshaft assemblies.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not loosen the rear axle wheel hub retainer until after the wheel and tire assembly are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied.
    With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. NOTE: Have an assistant press the brake pedal to keep the axle from rotating.
    Remove and discard the rear axle wheel hub retainer and the washer.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the brake hose, do not allow the disc brake caliper to hang suspended from the hose.
    Remove the brake disc.
    1. Remove the two bolts and lift the disc brake caliper and brake pads off the brake disc.
      • Using mechanics wire, position the disc brake caliper out of the way.
    1. Remove the brake disc.
  1. Remove the bolt retaining the parking brake cable bracket to the frame.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Cover the stabilizer link bolt threads and the nut to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a rubber hose approximately 37.5 mm (1.5 in) long, cover the stabilizer link bolt threads and nut.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The bolt that retains the upper ball joint to the knuckle is longer and it has fewer threads than the bolt that retains the toe link to the knuckle. Switching these bolts during installation will prevent the pinch arms on the knuckle from correctly retaining the toe link to the knuckle. This may cause the toe link to separate from the knuckle during vehicle operation. Failure to follow these instructions may result in personal injury.
    Remove the pinch bolts and disconnect the toe link and upper ball joint from the knuckle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the rear suspension upper arm to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a wood stick, approximately 450 mm (18 in) long and 25 mm (1 in) wide, support the rear suspension upper arm.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the outboard CV joint separates from the hub the knuckle will continue to pivot until the brake backing plate presses against the suspension lower arm. To prevent damage to the brake backing plate, immediately after separating the outboard CV joint from the hub, rest the knuckle on a cushioned support that is tall enough to keep the backing plate from pressing against the suspension lower arm.
    Separate the outboard CV joint from the hub and rest the knuckle on a cushioned support.
    1. Using the special tool, press the outboard CV joint until it is loose in the hub.
    1. Remove the special tool.
    1. Separate the outboard CV joint from the hub.
    1. Rest the knuckle on a cushioned support.
04ab306.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the axle shaft oil seal or the machined sealing surface on the inboard CV joint housing.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow the splines on inboard CV joint housing to touch the axle shaft oil seal.
    NOTE: A circlip retains the inboard CV joint housing to the differential side gear in the axle.
    Using the special tool, disengage the inboard CV joint housing from the differential side gear.
c231bc2.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the special tool before removing the inboard CV joint housing from the axle.
    Install the special tool.
50c5d1d.gif
  1. Remove the halfshaft assembly from the vehicle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the Differential Seal Protector before positioning the inboard CV joint housing in the axle.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always install the halfshaft with a new retainer circlip and a new rear axle wheel hub retainer.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never use power tools to tighten the rear axle wheel hub retainer.
    To install, reverse the removal procedure.

Apr 17, 2009 | Ford Explorer Cars & Trucks

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

Not finding what you are looking for?
2004 Ford Expedition Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...