Question about Cars & Trucks

Open Question

My clutch on my 1992 ford laser will not engage all the time. it was low on fluid so we topped it up and it was ok for a short time but used all the fluid and is getting worse. now it will pump up but

Have since bled it will only a small improvement. noticed a leak where the line goes into some rubber thing at the front and bottom of my engine. what is this?

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
freetek
  • 5568 Answers

SOURCE: soft clutch 1992 isuzu rodeo

If the seals around the shafts of master and slave are tight, they may be concealing a leak with fluid bypassing the piston seals internal to the two assemblies. Either your master or slave cylinders need to be replaced ot have new seals installed. Once you find the culprit and have installed a replacement, you will have to bleed the lines to evacuate air trap in the lines.

Posted on Mar 21, 2009

Ad
daves944
  • 1050 Answers

SOURCE: Clutch Whine on Toyota 4WD Pickup

There is a bearing that presses on the center of the clutch release arms when you put your foot down, it's called the clutch release bearing. It sounds like yours is starting to go bad. There is also a bushing or bearing in the back of the crankshaft that can cause this noise. the the input shaft of the transmission is stabilized in this. These two items are almost always replaced when a clutch job is performed. Unfortunately that is the only way to get at these two bearings. You may be able to drive the vehicle for quite a few more miles. but this is a sign of things to come.

Posted on Apr 06, 2009

emissionwiz
  • 76630 Answers

SOURCE: sticky clutch

mid level to higher, u have a worn out clutch, replace it before u damage the trans

Posted on Apr 14, 2009

  • 12 Answers

SOURCE: no clutch pedal pressure

if you have an adjustable pedal try that and if it still doesnt fix then youll have to replace all the O rings, that dont work then just go to a garage cause it will be cheaper dude then tryin everything

Posted on May 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a94 ford ranger regular cab 2.3 l 4 speed with over drive it will start but won't engage has little to no clutch pressure but I can get it in gear after pumping my clutch what's my problem


First, I would check the fluid in the master cylinder for the hydraulic clutch. If it is low, top it off. If the fluid level is low, it means you will probably need either the master cylinder, the slave cylinder, or both. These vehicles are extremely hard to purge the air out of the hydraulic clutch system. If you have to replace the clutch slave cylinder, you may need a proffesional.

Nov 22, 2014 | Ford Ranger Cars & Trucks

1 Answer

My 2001 nissan sentra clutch only engages at the top range of the pedal.


low fluid indicates a loss of fluid so top it up Check the slave cylinder for leaks at the piston . If ok replace the clutch master cylinder as the compensating port is blocking and not allowing the fluid to return to the reservoir and is holding the clutch off.

Mar 16, 2014 | 2001 Nissan Sentra

1 Answer

How and where do I top up a kj 94 model ford laser transmission and clutch


No vehicle consumes any fluids
No need to top up anything
If you find ANY fluid low, you have
a leak to repair

Jul 23, 2013 | Cars & Trucks

1 Answer

1992 ford escort


fill clutch master cylinder. there should be a slave cylinder at top of trans case. bleeder on slave cylinder. crack bleeder with clutch applied. (pump up and hold). do same thing until stright fluid comes out of bleeder.. clutch should be solid after this operation.

Dec 23, 2012 | 1992 Ford Escort 4 Door

1 Answer

Clutch is not engaging. Where do you check to fluid level? and what type of fluid do I use?


If a clutch is not engaging, you do not have a fluid problem. The clutch mechanism is only used to DISENGAGE the clutch.
If the clutch does not engage, you probably have a worn or damaged clutch plate. If that's the case, either the engine or transmission must be removed so that the clutch can be replaced.

Dec 08, 2010 | 1992 Saab 900

1 Answer

1994 Ford Probe GT Transmission


OK..............There is no transmission fluid just clutch fluid. Its in a small reservoir on the firewall. I think you have a worn clutch or it needs the lines adjusted. If the clutch doesn't engage until the pedal it almost at the top then you need to adjust it or replace it. The cleaner you put in is irrelevant to your problem. There is gear oil in the transmission though but that's not the problem either. The clutch cable is easy to adjust, just loosen the lock nut and spin the cable adjuster until the pedal feels right. Hope this helps :)

Jul 05, 2010 | 1994 Ford Probe

1 Answer

Ford F-250 Clutch Fluid resevoir location?


There will be a little black resevoir to the right of the brake master cylinder. Its mounted to the firewall. When filling or topping off the fluid, make sure you remove the black rubber boot after the cap is removed. The resevoir itself will only hold a little fluid. Hope this helps you. Please leave response if you could. :)

Mar 04, 2010 | 1992 Ford F250

3 Answers

Engine shuts off when put in gear


transmission tork converter lock has gone bad or bands are shot or the transmission is low on fluid.

May 29, 2009 | 1994 Ford Explorer Limited

1 Answer

Soft clutch 1992 isuzu rodeo


If the seals around the shafts of master and slave are tight, they may be concealing a leak with fluid bypassing the piston seals internal to the two assemblies. Either your master or slave cylinders need to be replaced ot have new seals installed. Once you find the culprit and have installed a replacement, you will have to bleed the lines to evacuate air trap in the lines.

Mar 21, 2009 | 1992 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...