Question about 2007 Ford Fusion I4 SEL Sedan

Open Question

Location of the cylinder head temp sensor on a 2007 Ford Fusion

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

craigjamesbt
  • 65 Answers

SOURCE: how do i change cylinder head sensor and where is it located

if you know engine fairly well the sensor should be pretty easy to spot it will be coming out of the cylinder head and have a wire attached to it although I haven't done much work on those models I wasn't aware they had that type of sensor are you sure your not looking for the temp sending unit? if so you will need to look on the intake manifold or near the water pump either way you may consider buying the sensor first then matching it with the wire/wires coming into it then simply unplug that sensor and unscrew (standard threads) make sure to properly seal the threads on the new one tighten to spec (be careful not to over tighten this component more than likely will thread into aluminum threads) better to be to loose and have to be tightened again than to have to replace a major component

Posted on Apr 26, 2009

chuck943
  • 783 Answers

SOURCE: location of CHT sensor

It is located at the back of the passenger side cylinder head close to where the intake manifold and head meet.It will have a YE/LG and GY/RD wires to it.

Posted on May 24, 2009

  • 1024 Answers

SOURCE: need location of temperature sensor on a 06 ford

4 cylinder engine
on the right rear of the engine
6 cylinder engine
on the rear of the engine above fly wheel

Posted on Mar 10, 2010

radar001
  • 1051 Answers

SOURCE: Ford Fusion 2009. where is

I use and I'd recommend you register for free at www.autozone.com Once registered you'll have access to repair and shop manuals for virtually any car or truck. All the data, specs and diagrams you need now or may need in the future will be a couple of mouse clicks away.

Posted on Aug 13, 2011

saa_aa
  • 241 Answers

SOURCE: location of the cylinder head temp sensor on a f250 2000

Did the problem come on suddenly or was some previous action or work done......

Posted on Nov 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2014 ford fusion engine wont crank after wreck


Ford fusion won't start - YouTube

? 2:01
www.youtube.com/watch?v=H0BhHWT2cyY
Sep 16, 2014 - Uploaded by mlmunoz21
Ford fusion won't start ... Published on Sep 16, 2014 .... 2004-2008 F150 Died Out No Crank Theft Light ...

Ford Fusion won't start - YouTube

? 0:32
www.youtube.com/watch?v=lmH7R6Ebmyc
Jan 9, 2015 - Uploaded by Nicholas A.
Any ideas why it won't start? 2007 ford Fusion awd 6 cylinder. ... And P1260 2007 Ford Fusion - Theft ...

Nov 02, 2015 | 2014 Ford Fusion

2 Answers

How to change engine cooling sensor on 2007 ford fusion


To begin, this year fusion had some issues with overheating problems which seem to be solved by 'bleeding' the coolant system of all air. Historically, an air bubble will become superheated and cause the temp needle on the dash to rise suddenly. This is often mis-diagnosed as a bad sensor, so initially be sure that the system is free of any air and is completely filled with coolant. http://www.fordfusionforum.com/topic/10969-engine-temp-gets-hot-sporadically/ If you do find that this does not solve the problem, and you determine that a sensor replacement is called for, it is always helpful to provide the engine size. The most popular engine was the 2.3 liter, 4 cylinder. If that is your motor, then it has two temp sensors. One is the cylinder head temp sensor and the other being the coolant temp sensor. If you have trouble code P0128, then this could be a result of a stuck thermostat, bad connection to the sensor or a bad sensor as you have determined. The reason I am providing all of this information is that you should eliminate other simple problems before replacing sensors. The temp sensor is located as an attachment to the water outlet adapter on the lower radiator hose. It is identified as part #19 in the attached diagram. http://www.autopartslib.com/2007-2-3l-ford-fusion-radiator-components-parts-diagram/ and is a threaded component. It sells for about $20. A pic of the part can be seen here: http://www.1aauto.com/coolant-temperature-sensor/i/1atsu00022?f=831037&y=2007&utm_campaign=gb_csv_br&utm_content=TSU&gclid=CPe2j_a7zr4CFdRj7AodJQoAvg. Again, I am guessing as to your motor size. Other sizes will have different applications. Good Luck!

May 28, 2014 | 2006 Ford Fusion

1 Answer

Where on the engine block is the location of 2007


The engine block is the base of the engine. Its the metal block base in your engine compartment.

Nov 03, 2013 | Ford Fusion Cars & Trucks

1 Answer

2001 Excursion 6.8 V10, hard start, high idle, code P1288 KOEO, and KOER, no memory codes, with temp gauge in normal range scan data reads 20 deg F, suspect CHT sensors looking for sensor location.


CHT -cylinder head temperature sensor located under the intake manifold.you have to remove intake manifold to replace sensor its in the cylinder head.

Oct 22, 2013 | Ford Cars & Trucks

1 Answer

Location for fuel filter 07 ford fusion


Ford Fusion 2007 user manual page 245 under FUEL FILTER" section. It states "Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance of replacement is not needed.

Aug 21, 2012 | 2007 Ford Fusion I4 SEL Sedan

1 Answer

Location of CHT sensor


It is located at the back of the passenger side cylinder head close to where the intake manifold and head meet.It will have a YE/LG and GY/RD wires to it.

May 24, 2009 | 2005 Ford Expedition

1 Answer

2001 focus/ect sensor


its screwed into the cylinder head ,when you fit a new 1 dont overtighten it they sense temp of the head they dont screw into the water jacket!!!!!!!!!!!!!!!!!!!!

Oct 09, 2008 | 2001 Ford Focus

Not finding what you are looking for?
2007 Ford Fusion I4 SEL Sedan Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...