Question about Cars & Trucks

Open Question

Torque settings for mac 350 velocette

Torque setting on head bolts

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mironate
  • 19 Answers

SOURCE: torque settings

  1. Tighten the cylinder head bolts sequentially in three steps. NOTE: Perform each step twice. 1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.) 2nd step torque: 69 Nm (7.0 kgf-m, 51 ft. lbs.) 3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.) Use a beam-type torque wrench. When using a preset-type torque wrench, be sure to tighten slowly and not to overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt, and retighten it from the first step.

Posted on Aug 06, 2008

  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

alicantecoli
  • 22095 Answers

SOURCE: what is 1996 1.6 8v cylinder head bolt torque settings

80 lbs

Posted on May 07, 2009

  • 1 Answer

SOURCE: i nead torque wrench setting for head bolts and cam bolts

Can anyone help us we need to know what is the setting for the cams in our Kia carnival Classic 2001

Posted on Jul 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is torque settings for head bolts on Kia pregio 2001


What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

Aug 17, 2015 | Kia Cars & Trucks

1 Answer

Toyota 80 series GLX auto landcruiser 1996 need head bolt torque a nd cam shaft torque settings


Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Nov 22, 2014 | 1996 Toyota Land Cruiser

2 Answers

What are the torque specs for the Main Bearing Cap bolts on a 1990 CHEVROLET TRUCK C1500 5.7l 350


main caps 85 ftlbs (3divdedsetings30ftlbs all 50 ftlbs all ending at85ftlbs click, rocaps 45ftlbs, head bolts 85ftlbs workingfrom cdenter top ,center botom ,top center working clock wizeand out ,intake boltes45ftlbs again fromcenter working outleft side, right side,left, right 8 bolts one time only or u will distort gasket. oilpan from center alternate L side ,R side,clock wize25ftlbsclick recheck after breakin period valve covers 25ftlbs anrecheck flywheel 90ftlbs ,harmnic balancer bolt 75ftlbs, add oil!!!!run for 15 minutes drain oil &change filter run for 100miles for molly rings 10 mmiles for cast rings .let engine cool down retorque headbolts,replace valve covers .run it and get on it!!! good luck hve fun.

Aug 20, 2012 | 1990 Chevrolet C1500

1 Answer

Need torque settings for cylinder head bolts on a 52 reg skoda fabia 1.4 16v any help much appreciated thanks


Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:

tdisline_116.jpg

IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Dec 17, 2010 | Volkswagen Polo Cars & Trucks

3 Answers

I need torque settings for the engine ie head bolts v6 engine 1


i am replacing the heads on a GMC 350 cu in engine. what is the final torque of the head bolts?

Jul 15, 2010 | 1985 Chevrolet Camaro

3 Answers

Head bolt torque specs and sequence for early 350 malibu motor


There are two different torque specs for this engine depending on which bolts you are torquing. This engine uses three different length bolts, the two sets of longer bolts can be torqued to 70 foot pounds, the short set of bolts that go along the bottom of the head should be torqued to 65 foot pounds. Head surface and block surface should be clean, straight and the a new head gasket should be used.

An easy way to guide yourself in the proper sequence is to make a cheat sheet of sorts. Take the headgasket and piece of cardboard about the same size. Using the headgasket as a template, mark each of the bolt holes on the cardboard with a sharpee marker, pencil or pen. Also outline the headgasket and mark the top of your drawing. Now starting from the center bolt as number 1, move either to the right or left, up or down to the next bolt hole and mark that as number 2. Now move to the bolt hole diagonally across from number 2, past Number 1 and mark it as number 3. Continue this sequence of moving diagonally back and forth across the headgasket outline until all of the bolt holes are marked with a number. What you are trying to do is start at the center of the head tightening it down in steps of about 15 foot pounds moving out from the center.

I have built a lot of these engines over the years and they are very forgiving of the head torquing sequence. As long as you start at the center and move out left and right, up and down alternating back and forth, you will have no problems. As a final check once you are done, check the torque on each head bolt to make sure you have not missed one. This does not have to be done in any sequence and you will then be sure that you have it completed properly. Good luck.

Apr 27, 2010 | Chevrolet Malibu Cars & Trucks

2 Answers

Torque setting cylinder head bolt 4 cylinder KIA sportage


I need the torque settings and pattern for a Kia Sportage 2.2

Nov 24, 2009 | 2001 Kia Sportage

1 Answer

Head bolt torque


They have this listed under a 2007 E-350 but I new it couldn't be. Any how the torque specs are as follows. The big bolts 1-26 are to be torqued first they are torqued to 120 ft. lbs. then rechecked to 120 ft. lbs. Then tightened 1/4 turn or 90 degrees. After that that loosen all the bolts up till the washers are loose again then perform the exact sequence all over again. After that tighten the small bolts on the outside part of the cylinder head all 7 of them to 20 ft. lbs. Good luck.

Apr 11, 2009 | 2007 Ford E-350 Super Duty Length XLT

2 Answers

Angle Torque settings head bolts


Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Jan 28, 2009 | 2000 Renault Sportwagon

4 Answers

Head bolts torque settings


According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Oct 26, 2008 | 1995 Land Rover Discovery

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...