Question about 2000 Mercury Grand Marquis

Open Question

How to replace the headlight assembly on a 2000 grand marquis

The plastic lenses are badly damaged by sand storms here in Arizona, want to replace entire lense assembly

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
warlock61
  • 659 Answers

SOURCE: i need a diagram of 2000 grand marquis serpentine belt

here you go

7d04ab2.gif

Posted on Dec 28, 2008

Ad
  • 4369 Answers

SOURCE: replace rear brake pads on a 2000 grand marquis

rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Posted on Mar 15, 2009

  • 83 Answers

SOURCE: 2000 grand marquis cruise control not working

Have seen this problem before. You need to look under dash at brake pedal and find a blue switch with plunger contacting pedal, disconnect connector and jump with a peice of wire and drive to see if cruise works and if it does replace deactivation switch this should get you going.

Posted on Aug 26, 2009

  • 173 Answers

SOURCE: Headlights work intermitently

HI,Inspect the #27 fuse holder of the Central Junction Box (CJB) for a questionable contact issue with the male spade of the fuse, which may cause intermittent loss of contact.if ok sounds like you need lcm= light control module.

Posted on Sep 30, 2009

  • 58 Answers

SOURCE: where are the spark plugs located on a 2000 Mercury Grand Marquis

There are eight COPs (coil-on-plugs) to remove. Using a 7mm or 9/32" socket, remove each bolt securing each COP to the intake manifold on top of the engine. Remove all eight COPs, and the spark plugs are underneath. When replacing the spark plugs, use only the proper Ford/Motorcraft plugs, even if they cost twice as much as the aftermarket ones. You will avoid further headaches this way. Hope this helps.

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace headlight 2004 grand marquis?


The Crown Vic and this Marquis are the same procedure, so please watch the video at this link

Aug 08, 2012 | 2003 Mercury Grand Marquis

1 Answer

Foggy headlight lens replace driver door mirror


Foggy headlight lens is from water ingress and gets trapped in there, the easiest way for you is to unscrew the back of the headlight assembly and get a hair drier and just dry out the head light, it may come back after a few rains,, other wise undo the screw holding the headlight unit, disconect wires and remove unit, I have the submerged unit into water watching where air bubbles come from then apply a small bead of water proof flexible sealand or silastic around the edge where the cover and lense meet, Dont try to take the lense off you will break something. Dry out completly and use hair dryer agin on low setting to make sure all moisture is gone and reassemble back onto vehicle....

Jun 21, 2010 | 1999 Mercury Grand Marquis

1 Answer

2004 merc grand marquis. how to adjust headlights, replace turn s


ther is a plastic guard with 3 locking caps that need to be turned clockwise a quarter turn to remove. remove from the front. you will then have be able to see and have access to the lights and adjustment screws

May 26, 2010 | 2004 Mercury Grand Marquis

1 Answer

Need to replace both front turn signal light bulbs on a 2000 mercury grand marquis. How?


Pop the hood, there is a tray that sits over the radiator, if the locks are still intact, twist them until the tray comes free, (There should be 3 plastic locks) remove the tray. Now you have access to the lights. There is an orange plug on both sides (L&R Headlights). Turn the plug until it frees up, then slide plug out of headlamp fixture. Then simply pull the bulb out and replace with new bulb.

Apr 24, 2010 | 2000 Mercury Grand Marquis

2 Answers

How to clean the headlights of a 2000 Jeep Grand Cherokee Limtied? They're very foggy and need cleaning. I do not have the money to replace them. Any advice is appreciated! Also, can they be cleaned if the...


was or is either hi or low non functional or do they in fact still work , note if you can manage the bulb itself out the back side which you should then a large {cotton-swab} would allow you to reach the inner glass that way ...otherwise a salvage yard would be much cheaper .

Dec 09, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Need directions for removing 1996 grand marquis headlights


Wanna save some money?...go to your nearest parts tore and ask them for a lense cleaning kit....the kit contains some very fine sand paper and a solution...rub the lense of your head light with the solution and paper and clean with a cloth, lights look as bright as new

Jan 03, 2009 | 1996 Mercury Grand Marquis

4 Answers

How do I replace xc90 headlight assembly?


its really easy. Open the hood, you will see two metal flat bars on the backside of each headlight, holding the headlight assembly on. Pull up on each of them.... remove headlight. Ta da.

Sep 19, 2008 | 2004 Volvo XC90

2 Answers

Headlights are foggy inside how do i clean them


the fogginess is caused by oxidation on the outside. normal wear and tear.

This is what i did on my honda civic 1996- bought three sand paper 600-1500 and 2000. Bought plastic shine from autozone and some plastic gloves.

1) I cleaned it with diluted soap to get all the dirt out. Use soft cotton cloth to do this.
2) get some clean water and dip sand paper(600) and start sanding the headlight. sanding should be done in the same direction throughout. I used horizontal strokes. Don't let the sandpaper dry out.
3) clean it out with water so all the sand particles from the sanding is cleaned out.
4) start with the next grade sand paper and repeat the process till you are satisfied and the fogginess is gone.
5) clean it thoroughly with water and let it dry fully.
6) put in gloves and rub plastic shine all over the headlight and leave it to dry. Make sure it does touch the paint!! you can mask the sides to avoid that.
7) clean it with soft cotton or polishing cloth. It really works!!!

Also, stay away from direct sun while doing this. Having the hood up is helpful.

Lis

Jul 12, 2008 | 2001 Mercury Grand Marquis

Not finding what you are looking for?
2000 Mercury Grand Marquis Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...