Question about 2010 Mitsubishi Lancer

Open Question

Replacing serpentine belt Mitsubishi lancer 201 0

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mike258
  • 1498 Answers

SOURCE: serpentine belt replacement

Hi Paul,

The routing diagram is under the hood.

  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Posted on Dec 14, 2008

  • 8 Answers

SOURCE: How to loosen alternator tension on a 2003 Lancer

I have not seen this vehicle but, the center bolt or nut that holds the tensioner to the block is backed off two turns first.
Then the adustment bolt (most are accesed from under the vehicle) can be adjusted to give enough slack to install the new belt.
If this is still too tight, remove one of the two or two of the three bolts that mount the Alternator to allow for another 1/8" and install the belt.
Then remount the Alternator.
Then readjust the tension bolt.
Finish with the bolt or nut that mounts the tensionor to the block.
good luck.

Posted on Jun 28, 2009

  • 4088 Answers

SOURCE: serpentine belt diagram 3.5 litre v-6 2001 mitsubishi Montaro lim

Check with Autozone--their belts have the diagram on the box.

Posted on Feb 08, 2010

  • 1757 Answers

SOURCE: diagram for serpentine belt on a mitsubishi galant es

My sincere apologies for the severely delayed response.
I am going back to answer - unanswered questions. I have only been on this site for the past 4-months. Questions Posted have exploded (+55%) since joining.

I do not know if you still need this information, but I am answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks.
http://www.2carpros.com/car_repair_information/year/2002/make/mitsubishi/model/galant/2002_mitsubishi_galant_drive_belt_routing_diagram.htm

Posted on Mar 04, 2010

  • 1757 Answers

SOURCE: mitsubishi lancer evolution 8 timing belt

Sorry for the delay. I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.
Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2003/make/mitsubishi/model/lancer/2003_mitsubishi_lancer_timing_belt_diagram_marks.htm

Posted on Mar 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Mitsubishi lancer serpentine belt


You should have a diagram close to belts.

Mar 16, 2013 | 2008 Mitsubishi Lancer GTS CVT Sedan

2 Answers

I am trying to hange the serpentine belt on my 09 lancer rallyart and it keeps slipping off


Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2 Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.
  • 3 Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.
  • 4 Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.
  • 5 Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.
  • 6 Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.
  • 7 Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.
  • Oct 25, 2011 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    What is serpentine of lancer 2002 Its a belt??


    THAT'S IS YOUR SERPRNTINE MULTI ACCESSARY BELT THAT RUNS AROUND ALL YOUR COMPONENTS.











    TIM

    Dec 23, 2010 | 2002 Mitsubishi Lancer

    1 Answer

    Replace alternator belt


  • Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2

    Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.

  • 3

    Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.

  • 4

    Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.

  • 5

    Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.

  • 6

    Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.

  • 7

    Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.

  • Oct 08, 2010 | 2002 Mitsubishi Lancer

    1 Answer

    How do i change the timing belt in a 2003 mitsubishi lancer es


    Hi, first pop the hood and find the serpentine and alternator belts on the left side of the engine compartment. The serpentine belt runs around four pulleys. The alternator belt uses two pulleys. They share space on the drive shaft so they are right next to each other.
    Of the four pulleys using the serpentine belt, three of them are vertically in line (closer to the front of the car) and the fourth stands alone (closer to the cab). Of the three vertically in line, the middle pulley is the one used to adjust the tension on the belt.
    You must first break loose the bolt in the center of the tension pulley (the bolt is facing the passenger tire) by turning it counter clockwise. Then leave that bolt and go to the bolt connected frame connected to the other side of the tension pulley (this bolt is facing the front of the car). Turn that bolt counter clockwise until the serpentine belt is loose enough to pull off. Replace the belt and tighten in the opposite order. Once the desired tension is reached, crank the car and run it for a few minutes. Finally cut the car off and check the tension, tighten or loosen as necessary.
    Take care

    Aug 02, 2010 | 2003 Mitsubishi Lancer

    1 Answer

    I am trying to change the serpentine belt on my 2008 lancer gts. Thank you so Much!! Hollie


    First, you need to have the diagram for how the belt is routed when you replace it.

    Serpentine routing diagram...

    9c37528.jpg
    Here is a link to a video on how to replace the serpentine belt. I hope it helps!

    http://www.wonderhowto.com/how-to-inspect-replace-cars-serpentine-belt-267229/

    Feb 20, 2010 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    How to change the Serpentine belt on a 2008 lancer?


    First, you need to have the diagram for how the belt is routed when you replace it.
    Serpentine routing diagram...


    a55b974.jpg
    Here is a link to a video on how to replace the serpentine belt. I hope it helps!

    http://www.wonderhowto.com/how-to-inspect-replace-cars-serpentine-belt-267229

    Nov 21, 2009 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    How do I replace a broken alternater belt on a 2003 mitsubishi lancer


    First pop the hood and find the serpentine and alternator belts on the left side of the engine compartment. The serpentine belt runs around four pulleys. The alternator belt uses two pulleys. They share space on the drive shaft so they are right next to each other.
    Of the four pulleys using the serpentine belt, three of them are vertically in line (closer to the front of the car) and the fourth stands alone (closer to the cab). Of the three vertically in line, the middle pulley is the one used to adjust the tension on the belt.
    You must first break loose the bolt in the center of the tension pulley (the bolt is facing the passenger tire) by turning it counter clockwise. Then leave that bolt and go to the bolt connected frame connected to the other side of the tension pulley (this bolt is facing the front of the car). Turn that bolt counter clockwise until the serpentine belt is loose enough to pull off. Replace the belt and tighten in the opposite order. Once the desired tension is reached, crank the car and run it for a few minutes. Finally cut the car off and check the tension, tighten or loosen as neccessary.

    Oct 10, 2009 | 2004 Mitsubishi Lancer

    2 Answers

    2003 Lancer ES High pitch squeal and constant squeak


    Shortly after replacing the serpentine belt in my lancer, the same thing happened. It is NOT the timing belt. Belts squeal when they slip. If your timing belt slipped it would cause your car to run funny.

    have somebody check the belt for wear (or do it yourself), replace if necessary. If it doesn't need replacement, just tighten it.

    If you have the 4cyl engine that I have, the tightening is kind of a pain in the ****. Not a great design by mitsubishi. There's a pulley near the front right corner of the engine in front of the alternator. the belt should be running around this pulley GROOVE SIDE OUT. This is the tension pulley.

    To tighten:
    1) Lightly loosen the bolt in the center of the pulley (slightly loosen, DO NOT REMOVE).
    2) Under that pulley there's another bolt. You can see that the bolt goes through a piece of metal
    attached to the back of the pulley. Figure out which way you need to turn the bolt to move the
    pulley toward the front of the car. (i don't remember if it's right hand thread, or left hand) This
    puts extra tension on the belt. You probably don't need much. Over tensioning the belt can
    cause pulley bearing failure. If you haven't done this work before, ask someone for
    help
    . It's better to tighten a little bit, a few times rather than overtighten once.
    3) Don't forget to ReTighten the bolt in the center of the pulley.

    If there's lots of cracks and pieces missing on the ribs or grooves of the belt you should replace it first.

    Happy repairing,
    Cliff

    Mar 07, 2009 | 2003 Mitsubishi Lancer

    Not finding what you are looking for?
    2010 Mitsubishi Lancer Logo

    Related Topics:

    64 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts

    yadayada
    yadayada

    Level 3 Expert

    75077 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7768 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...