Question about 2000 Mitsubishi Lancer

Open Question

Diagram for serpentine belt Mitsubishi lancer 2010

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Mike258
  • 1498 Answers

SOURCE: serpentine belt replacement

Hi Paul,

The routing diagram is under the hood.

  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Posted on Dec 14, 2008

Ad
ewashmidas
  • 362 Answers

SOURCE: timing belt diagram lancer 1.5 1988

Here's the picture of the timing marks.

0e3bbfd.png

Posted on Jan 31, 2009

  • 8 Answers

SOURCE: How to loosen alternator tension on a 2003 Lancer

I have not seen this vehicle but, the center bolt or nut that holds the tensioner to the block is backed off two turns first.
Then the adustment bolt (most are accesed from under the vehicle) can be adjusted to give enough slack to install the new belt.
If this is still too tight, remove one of the two or two of the three bolts that mount the Alternator to allow for another 1/8" and install the belt.
Then remount the Alternator.
Then readjust the tension bolt.
Finish with the bolt or nut that mounts the tensionor to the block.
good luck.

Posted on Jun 28, 2009

  • 17 Answers

SOURCE: I need the serpentine belt routing diagram for

Most vehicles have the routing in the engine compartment, near the top of the radiator or underneath the hood. If no luck consult your owners manual.

Posted on Dec 21, 2009

  • 1757 Answers

SOURCE: diagram for serpentine belt on a mitsubishi galant es

My sincere apologies for the severely delayed response.
I am going back to answer - unanswered questions. I have only been on this site for the past 4-months. Questions Posted have exploded (+55%) since joining.

I do not know if you still need this information, but I am answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks.
http://www.2carpros.com/car_repair_information/year/2002/make/mitsubishi/model/galant/2002_mitsubishi_galant_drive_belt_routing_diagram.htm

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need a diagram


This is the routing for the 1.8L, 2.0L and 2.4 l engines.
3e49ec83-f61c-4429-afd8-f20387ba2dcc.jpg

Jul 29, 2014 | 2005 Mitsubishi Lancer

1 Answer

How to replace a serpentine belt on a 2010 Kia Forte?


kia forte drive belt - Kia Forte Forum : Sedan / Koup / Forte5 Forums

www.forteforums.com/.../kia-forte-2-0l.../40769-kia-forte-drive-belt.htm...

Dec 19, 2013 - 8 posts - ‎3 authors
im trying to replace the drive belt on a 2010 kia forte ex 2.0l and was wondering if someone could get me a diagram of the belt routing as well ... Squeal in serpentine belt area even after replacing ...
3 posts
Nov 8, 2014
Serpentine drive belt -very frustrating-
15 posts
Jun 17, 2014
Recommended mileage timing chain change SX
11 posts
Mar 23, 2014
Serpentine belt removal on a 2.4L. Anyone?
5 posts
Aug 11, 2013
More results from www.forteforums.com
images for serpentine belt diagram on a 2010 Kia Forte

Jul 03, 2014 | 2010 Kia Forte

2 Answers

Mitsubishi lancer serpentine belt


You should have a diagram close to belts.

Mar 16, 2013 | 2008 Mitsubishi Lancer GTS CVT Sedan

2 Answers

I am trying to hange the serpentine belt on my 09 lancer rallyart and it keeps slipping off


Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2 Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.
  • 3 Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.
  • 4 Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.
  • 5 Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.
  • 6 Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.
  • 7 Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.
  • Oct 25, 2011 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    Replace alternator belt


  • Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2

    Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.

  • 3

    Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.

  • 4

    Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.

  • 5

    Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.

  • 6

    Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.

  • 7

    Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.

  • Oct 08, 2010 | 2002 Mitsubishi Lancer

    1 Answer

    I am trying to change the serpentine belt on my 2008 lancer gts. Thank you so Much!! Hollie


    First, you need to have the diagram for how the belt is routed when you replace it.

    Serpentine routing diagram...

    9c37528.jpg
    Here is a link to a video on how to replace the serpentine belt. I hope it helps!

    http://www.wonderhowto.com/how-to-inspect-replace-cars-serpentine-belt-267229/

    Feb 20, 2010 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    How to change the Serpentine belt on a 2008 lancer?


    First, you need to have the diagram for how the belt is routed when you replace it.
    Serpentine routing diagram...


    a55b974.jpg
    Here is a link to a video on how to replace the serpentine belt. I hope it helps!

    http://www.wonderhowto.com/how-to-inspect-replace-cars-serpentine-belt-267229

    Nov 21, 2009 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    How to loosen alternator tension on a 2003 Lancer


    I have not seen this vehicle but, the center bolt or nut that holds the tensioner to the block is backed off two turns first.
    Then the adustment bolt (most are accesed from under the vehicle) can be adjusted to give enough slack to install the new belt.
    If this is still too tight, remove one of the two or two of the three bolts that mount the Alternator to allow for another 1/8" and install the belt.
    Then remount the Alternator.
    Then readjust the tension bolt.
    Finish with the bolt or nut that mounts the tensionor to the block.
    good luck.

    Jun 27, 2009 | 2003 Mitsubishi Lancer

    Not finding what you are looking for?
    2000 Mitsubishi Lancer Logo

    Related Topics:

    144 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...