Question about 1994 Geo Tracker

Open Question

Procedure for timing the ignition on a 1994 Geo Tracker

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: HOW DO YOU REMOVE THE RADIO FROM A 1995 GEO TRACKER????????

To remove the radio:
Remove the ashtray by raising the armrest cover and removing the two screws at the rear of the ashtray. Slide the ashtray back and then lift it out. Be careful of the two front tabs, as you don't want to break them.
Reach below the wood console, where the ashtray front tabs were inserted. Loosen and remove the two wing nuts.
With a small, long flat bladed screwdriver, pry out the leather shifter surround. The leather shifter surround has a center chrome retaining ring, the leather surround, and then finally a black plastic surround. The chrome retaining ring has 3-4 tabs which are locked in below the leather surround. It depends on the year of the Jaguar. Probably the 95 has three, but maybe four. They should be at the front and rear of the trim piece (2 front and 1 back, or 2 front and two back) but I've seen then on the sides. The point is, you have to be careful with the screwdriver and find the tabs. The screwdriver should be slid between the leather and the retainer. Pull upwards on the retainer gently, and as you loosen the tabs, it will come out.
Remove the leather surround. Once the chrome retainer has been removed, it should be easy to work it out of the console.
Loosen the black trim ring gently as it has tabs as well, but they are visible once the leather trim has been removed. Lift it upwards out of the wood trim and pull it to the side out of the way. You don't need to disconnect the wires, just lay the black trim to the side.
Lift the rear of the wood console trim and gently, gently slide it back and up. It will try to hang on the leather console, and can be difficult. Patience is important, as the walnut on the ski slope cracks easy (really easy).
Once the wood console trim (ski slope) is removed, you should have a row of screws up the side of the center control panel, where the radio and AC controls are. There are four to six on each side, depending on what Jaguar used at the time, as the 95 cars mechanically are somewhat of a blend of the XJ40 and the XJ300. Remove these screws, and note any spacers that were behind them. These spacers get lost quickly, and cause the ski slope to sit awkwardly on the console.
The radio will slide forwards once these screws are removed. Remove the radio harness and the antenna lead. As the books say, assembly is reverse of removal.
Good luck, and let me know if you have questions. If you are replacing the radio, let me know as I have the harness wiring codes and can help you with that as well.

Posted on Jul 01, 2008

  • 398 Answers

SOURCE: what are the symptoms of a bad egr valve ina 1994 geo tracker?

this may help
EGR Theory. EGR serves one purpose and one purpose only. That purpose is to reduce Oxides of Nitrogen (NOx). Undernormal combustion, Nitrogen(N2)Oxygen (O2) in the air and Hydrocarbons (HC) in the fuel combind into water(H2O) Carbon dioxide (CO2) and the Nitrogen remains unchanged. Under very hot combustion temperatures, the Nitrogen reacts with the other two byproducts and forms Nitrogen oxide (NO). After being released into the atmosphere, it picks up another Oxygen and becomes Nitrogen dioxide (NO2). In the presence of sunlight,
it combines with other compounds like Hydrocarbons and forms Smog. Since exhaust gas is inert (very stable) it doesn’t burn again. So by being introduced into
the combustion chamber, it will lower combustion chamber temps enough so that
the Nitrogen doesn’t react with the other compounds and is passed unchanged out
the tailpipe thus not contributing to smog. Now, since exhaust gas doesn’t burn, it
doesn’t exactly help with combustion. At higher RPM’s, this really isn’t noticable,
but at idle, the reintroduction of exhaust gas will cause a very rough idle and can
cause stalling if to much is introduced into the combustion chamber

Posted on Mar 07, 2009

  • 2 Answers

SOURCE: reset check engine light on 1995 geo tracker

I had the very same problem with my 94 tracker and it turned out to be something simple. My check engine light had popped on after it had hit 100,000. I went through all of the suggestions that people had suggested (unplug battery......etc) and still to no avail. Searching the internet, I came across a website called suzukiforum.com and there, this guy was able to help me with my problem. It turned out to be a maintenance switch that kicks on every 50,000 miles. This switch is like a secret that the auto manufactures use to ploy owners of their cars to bring to the dealer and then rack up the dollars in unnecessary "repairs". The switch is located under the dash and can be hidden anywhere. From the assistance of the guy on the forum, he was able to send me photos of this damn switch and possible locations where it may be mounted. I found mine in about 5 minutes, where it was attached to the steering column. It's a tiny switch, that you slide up or down, depending on what position it is in upon finding it. If it's up, then slide it in the down position and visa versa. Once you do this, the check engine light will go off. Make sure you do not have the car running and you can even unhook one of the battery posts, just to make sure you don't hit anything while rooting around under the dash. Good luck!

Posted on Apr 30, 2009

  • 137 Answers

SOURCE: 96 geo tracker setting base ignition timing is

gee , try my ign page.
you need to place a jumper to freeze the Ignition timing.
1 static timiing.
2; dynamic timing (running ) needs a jumper

http://www.kick-fix.com/IGN_timing/index.html

Posted on Oct 22, 2009

  • 1757 Answers

SOURCE: looking for timing belt diagram on 97 Geo Tracker

Click on the following free, direct Link. It has the Timing Belt Diagrams, including Marks and Instructional Diagrams.

Let me know if this helped...

http://www.2carpros.com/car_repair_information/year/1997/make/geo/model/tracker/1997_geo_tracker_timing_belt_diagram_marks.htm

Posted on Apr 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many quarts transmission fuild needed for 1993 tracker manual geo chevy How many quarts of transmission fuild needed for geo tracker 1993 manual


lost he operators guide>? glove box

go here
http://www.fixkick.com/index9.html
click 1994 book
see page PDF 201, there it is, and all other like facts,

save the book so next time have one.

Feb 13, 2015 | Geo Cars & Trucks

1 Answer

How to replace distributor 1994 geo 1.6 8 valve


does it run now? cap too? and HV wires? (yes,y and y ,i guess)
if runs: (mark wires properly, 1,2,3,4 as they go, cap and wires marked ! 1 is front, firing order is 1,3,4,2.
1: off the cap, mark rotor position at dizzy body. tip to body edge.
Do not crank over the engine, (by hand or keys)
2: put it back ,with rotor same place.
easy huh?
but if you lost the timing, its 8 steps. (not counting the fine tune)

http://www.fixkick.com/IGN_timing/8v-procedure.html#fastplant


old post.

Apr 23, 2014 | 1994 Geo Tracker

1 Answer

Have a 1994 geo trackre taat turns ovre but will not start up do the computer have anything to do with why the car wii not start


very old post. but searches will land here.

yes, has everything, if cranks ok
the ecu makes spark, via the igniter then coil.
http://www.fixkick.com/nostart.html

Nov 21, 2012 | 1994 Geo Tracker

1 Answer

96 geo tracker setting base ignition timing is there a connector to unplug or what


gee , try my ign page.
you need to place a jumper to freeze the Ignition timing.
1 static timiing.
2; dynamic timing (running ) needs a jumper

http://www.kick-fix.com/IGN_timing/index.html

Sep 28, 2009 | 1996 Geo Tracker 2 Door

1 Answer

Ignition and steering wiring


You maybe better off buying a steering colum or a new harness at a salvage yard.

Feb 10, 2009 | 1994 Geo Tracker

1 Answer

1994 tracker


You may have an issue with the fuel pump crank circuit, check the ignition switch, I think that may be the problem

Aug 22, 2008 | 1992 Geo Tracker

1 Answer

1994 geo tracker fuel problem


The fuel pump has 2 sources of power, when you crank the engine power to the pump is supplied through the cranking circuit of the ignition switch, after it starts the power comes from the run circuit, you most likely have an issue with the ignition switch.

Aug 22, 2008 | 1992 Geo Tracker

Not finding what you are looking for?
1994 Geo Tracker Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...