Question about 1995 GMC Sierra C1500

Open Question

HOW TO CHANGE UPPER AND LOWER BALL JOINTS ON A 2001 GMC 1500 PICKUP TRUCK

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
shawnsz
  • 64 Answers

SOURCE: lower ball joint replacement 2003 GMC Sierra 2WD

You have to drill them out, it can be a real pain to.

Posted on Feb 19, 2009

Ad
motor1258
  • 6674 Answers

SOURCE: can't take off ball joints upper and lower

Pretty sure on that vehicle you have to press them in & out, if no bolts there to hold them in. Some autoparts stores will lend you the proper tool.

Posted on Mar 14, 2009

c17hydro
  • 2984 Answers

SOURCE: 1997 gmc yucon 4X4 ball joint removal

Okay, more than likely you are going to need to take the upper and lower arms in to have the old joints pressed out and then pressed in. If you can buy the replacement joints and take them in, you will save a WHOLE lot of cash. You could also do this yourself if you have a hydraulic press or, if you can swing by an auto parts store that rents out tools......it looks like a modified c clamp.

Posted on Mar 14, 2009

emissionwiz
  • 76848 Answers

SOURCE: how to remove upper/ lower ball joints on 1990 GMC Suburban 4x4

hit the steering knuckle where the ball joint shaft goes through it while u have the wedge/pickle fork inserted, u do this on the round side of the knuckle, this is what is called a "Morse Taper" hitting it distorts the hole a little and that lets the joint pop free. You need at least a 5 pound ball pen for this to work..

Posted on May 12, 2009

  • 113 Answers

SOURCE: I need step by step

first you will need to buy a ball joint press. first jackup and place jack stand under oneside of jimmy1).remove the tire.2)remove caliper and pads and rotor.3) remove cotter pin out of nut for tie rod end then remove nut. 4) loosen tie rod end from knuckle donot split greese boot or hit top of stud as this will damage it.5)remove axle nut and push back axle may be frozen in hub.6) remove both cotter pin and nuts on ball joints then spin on bottom nut a couple threads as no thave knuckle fall to the ground.7)loosen ball joint from knuckle and remove knuckle.8) remove ball joints with press or by rmoving rivits install in reverse procedure

Posted on Sep 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clunking?


Retest the fitting and inspect the ball joints again to confirm its not the issue.For that click the help links shown below :----Upper Ball Joints inspection and replacement? http://howtobyme.blogspot.in/2012/02/upper-ball-joints-inspection-and.html How to Test Upper and Lower Ball Joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-test-lower-ball-joint.html How to inspect Upper and Lower Ball joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-inspect-lower-ball-joint.html How to Service Ball Joints on Car? http://repairhelpcenter.blogspot.com/2011/12/how-to-service-lower-ball-joints-on-car.html How to Replace Ball joints? http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-lower-ball-joints.html Lower Ball Joints replacing on car? http://howtobyme.blogspot.in/2012/02/lower-ball-joints-replacing-on.html
--------This will help.Thanks.

Jan 23, 2012 | 2000 GMC Yukon Denali

1 Answer

How do you change a front axle u-joint on a 2006 3500 dodge ram


you will have to change both sides to start with. I'm doing this on a 1996 ram 1500. first, put the truck on 2 wheel drive or neutral for traction, raise vehicle, i got a lift it's easy, remove both wheels, calipers and rotors. unlock the driveshaft nut (cotter pin) and unbolt that nut. on the inside of the hub, first mark the relation on one side between the yoke and the shaft, then, there is 3 bolts holding the hub in, remove them. next, more cotter pins, upper and lower ball joint and tie-rod end need to come out, so, unscew the tie-rod end first and seperate it with ball joint seperator. do the same for the upper and lower ball joints. seperate the spindle and the axel should come out. the rest is standard procedure to change a ball joint.
let me know if it's enough info or if you want more please.

Jan 04, 2011 | 2008 Dodge Ram Pickup 3500

3 Answers

I need to replace the lower ball joints. The new joints have a 4 bolt design.


That 4 bolt design is for the upper ball joint, the lower ball joint in press in, that the wrong one you have.

Jul 05, 2010 | 2003 GMC Sierra 1500

1 Answer

How do i change the upper and lower ball joints on


The upper and lower ball joints are riveted in on the oem ball joints you have to cut the rivets and then use a balljoint press to press them out the new ball joints have nuts and bolts just press them back in and tighten down the nut

Jan 20, 2010 | 2000 Dodge Ram 1500 Truck

1 Answer

Dont know where the upper and lower ball joints are located


If you turn the steering one way fully, looking behind the front wheel, you will see a pair of ball joints, one above the brakes, and the other below, very close to the wheel.
They are each attatched to a wishbone shaped component.The upper and lower.

Aug 27, 2009 | 2004 Dodge Ram 1500

1 Answer

Upper and lower ball joints


Jack the truck clear of the ground and let the wheel assembly hang. After you remove the tire place your jack under the lower control arm so it's firm. Remove the cotter pin, if you have one and loosen the big nut almost off. Wedge a "pickle fork" between the control arm and the spindle and give it a belt with a hammer until the ball joint pops. Raise the jack so you can undo the nut easily and separate the control arm and spindle.
The upper ball joint is riveted or bolted in. Grind the rivets or use a cold chisel and remove the ball joint. Clean up the area with some sandpaper, dirt , loose rust, etc.and put the new joint in. Put the spindle back on using the jack if necessary and put the nut back on and tighten.
The lower ball joint is pressed in. Tie the spindle out of the way and brace the lower control arm with some blocks or the jack if you have to. A few whacks with a hammer should pop the joint out. Clean the hole out lightly, just to remove loose rust and dirt. Put the ball joint, minus the grease fitting ,,in the hole and use the jack with a block of wood, to put it in place.You may have to fiddle with the spindle to make sure it is lined up. I've never had any trouble using a 1ton trolley jack and the weight of the truck to put the lower ball joint back in. Replace the nut and grease fitting.
The new ball joints will probably come with cotter pins, use them. Make sure the new joints are tight or they will wear the holes in the spindle. Don't forget to grease the new joints. Hope this helps.

Jul 13, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Replacing Ball Joints on 2001 Mazda B2500 (upper and lower)


its easier to get the whole control arm and the lower one has to be pressed in. it is not and easy job if you dont have the right tools checkout rockauto.com to look at the replacement parts and to get a price on them

Jan 07, 2009 | 2001 Mazda B-Series

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...