Question about Oldsmobile Cutlass Supreme

Open Question

1987 cutlass salon main power relay

No power to radio or headlights

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bibleman01
  • 334 Answers

SOURCE: change radio

you just pop off the trim around the radio, Then everything else is easy. Use the tip of a screw driver and just pry gently.

Posted on Jan 04, 2009

  • 2 Answers

SOURCE: no power to anything besides power windows and car runs

1st thing i would do is check fuses. when my brakelights went out it was just a fuse.

Posted on Jan 20, 2009

ButtFuzz
  • 463 Answers

SOURCE: Olds Cutlass factory radio/cassette, radio doesn't work.

When you say tried different radio and it didn't work, does this mean the tuner acts like it is functioning, but you hear nothing out of the speakers?

If so, this stinks of a bad ANTENNA...

Posted on Mar 05, 2009

csmock132
  • 4669 Answers

SOURCE: Can I install a 1985 Olds. Engine in an '87 Olds Salon?

Yes, it will go right in.

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rocker arm pivot torque for olds cutlass 1987 307


Oldsmobile Torque Specs - GbodyOlds.com

www.gbodyolds.com/forum/showthread.php?754-Oldsmobile-Torque...
Feb 7, 2013 - 2 posts - ‎2 authors Oldsmobile Small-Block Engines Cylinder Head Bolts (1/2in. bolt) 130 ft. lbs. Cylinder Head ... Rocker Arm Pivot Bolt 25 ft. lbs. Rod Bearing ...

Rocker Arms - AutoZone

www.autozone.com/...Cutlass...1987.../Rocker-Arms/_/P-0900...

AutoZoneGM Cutlass RWD 1970-1987 Repair Guide ... To remove the rocker arms from the shaft, the nylon arm retainers must be removed. ... 7: Engine valve system, 260, 307, 350, 403 Oldsmobile built engines ... Unfasten the two bolts that attach the rocker arm pivot to the cylinder head. ... Torque the retaining bolts to 25 ft. lbs.

Dec 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

How do i get a spark on a 1987 cutlass salonI it crank but no spark...it keeps crankin but it wont start...wat could be da problem???


if the coil is known to be good check in the distributor cap whether power is getting there. if it is there must be something wrong with the spark leads.
Essentially you must work backwards from the spark plug tips towards the battery until you find where the transmission of power breaks down. So check for a spark at the plug tips.
if no power check the centre of the distributor cap, and if no power check the coil. at some point you will find power, the problem then, must be between the place you find power and the next step that should go but does not
Good Luck

Jun 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

Fuse panel location


the fuse box is located lower dash drivers side ,cover/lid usually has list inside to the fuse locations etc, does the four way switch turn the signal lights on ? if so the fuse for the turn signals is probably the issue , if the four ways don't come on it may be the flaher relay which may be in the interior fuse box but if not the fuse box in the engine compartment is the next place to look, hope this helps

May 24, 2014 | 1987 Oldsmobile Cutlass Salon

1 Answer

What size engine and transmission do i need for 24inch rims?


best bang for your buck 350 cid with a turbo 350 or 700r4 ... the 350 engine can be stroked out to 383 using the internals:pistons and crank from a 400 in big block... but just stroking a 350 on a hot tranny with low gears to drive those big wheels is important get a 4;11 low gear ratio you ll be able to drag that monster.

May 08, 2009 | 1987 Oldsmobile Cutlass Salon

1 Answer

Change radio


you just pop off the trim around the radio, Then everything else is easy. Use the tip of a screw driver and just pry gently.

Jan 04, 2009 | 1987 Oldsmobile Cutlass Salon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...