Question about Mazda Cars & Trucks

Open Question

Fault code p138b

Vehicle in limp home mode

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 323 Answers

SOURCE: limp mode?

It may have a "loss of prime" code that usually follows a service of the fluid and filter. After you're sure the fluid is full at operating temperature, disconnect the battery for a few minutes and reconnect to see if the code resets. I hope this helps.

Posted on Apr 26, 2009

Ad
  • 1779 Answers

SOURCE: limp home mode

You need to scan for engine trouble codes. Most parts stores will do this for free, and tell you what they mean and make recommendations on what to do. The 'limp mode' kicks in to prevent damage to the vehicle when the computer gets data that something is wrong.. When you shut it off, it's temporarily reset, but then the cars computer is signaling there is still a problem, and it goes back into limp mode. If you have any questions after getting the codes 'read' , post questions and code #;s here for help. Good luck.

Posted on Apr 28, 2009

  • 1 Answer

SOURCE: My Audi A3 2.0 tdi limp mode/turbo overboost

i also have done a diagnostic test and it states a turbo overboost condition and it drives fine locally but loses power on the motorway and struggles to reach 80mph? any suggestions please email me at shiz86@hotmail.co.uk

Posted on Sep 14, 2009

  • 750 Answers

SOURCE: Holden rodeo 99 3.2v6 4l30e code 82 and going into limp mode

the tcm may be faulty or has a loose ground, try swaping in another if you can get one borrowed or a cheap used one from a salvage unit

Posted on Oct 30, 2009

  • 246 Answers

SOURCE: fault codes p1211 and p0251 keeps putting my van

Fuel injection circut malfunction.
How many cylinders

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do u mean limp mode on a Ford falcon and How To reset It


Limp mode is a setting which is made by the Engine Control Module that limits the vehicle performance to protect itself. You need to take it to a garage, they will put a code reader on it and tell you what sensor is reporting a fault and what the fix is. Resetting the computer without fixing the underlying problem can be catastrophic to the engine.

Now, having written all of the above, this is an old vehicle, so codes and ECMs do NOT apply.

Have a read of this

https://www.google.ca/search?q=Ford+falcon&ie=utf-8&oe=utf-8&gws_rd=cr&ei=vbXlWPuQM8HEjwO2lp6YBw#q=ford+falcon+au+limp+mode&*

limp mode Google Search

Ford falcon limp home mode - Google Search

Apr 06, 2017 | Ford Cars & Trucks

1 Answer

What might cause 2004 4l80e to be in limp mode no speedometer and stuck in 2nd gear


When the system goes into to Limp Home mode it means that a serious fault has occurred in the electronics or a mechanical failure has been sensed. What you need to do now is have the computer control system scanned for fault codes, this (the fault codes) will give you a starting point to diagnose the problem that has caused the Limp Home mode to be initiated by the computer control module.

Dec 20, 2016 | Cars & Trucks

1 Answer

WHY DID THE CAR GO INTO LIMP MODE. WHAT IS THE POSSIBLE CODES AND REASONS FOR LIMP MODE AND HOW DO WE RESOLVE IT


Most limp modes are caused by transmission faults but can be caused by engine sensors and blown fuses. If your car is in limp mode the fault will be stored in the ECM.
You need to read the fault codes stored in your ECM to know which sensor has caused this problem. You didn't say what model vehicle you have and it would take a number of hours to list all the possible codes and reasons.
Get someone with a code reader for your model vehicle.

Sep 17, 2015 | Cars & Trucks

1 Answer

Ranger 800 limp mode error code 652 ??


If there is a fault with the engine the computer will go into limp home mode . a code reader number will give you the fault, after the repair the computer will have to be reset .

Sep 21, 2014 | Cars & Trucks

1 Answer

Reduced engine power


Your vehicle seem to have gone into limp home mode. You need to have the fault codes pulled to know what is wrong. Limp mode lets you get home but limits engine output function.

Nov 17, 2013 | 2004 Chevrolet TrailBlazer

1 Answer

Navara d40 has no power wont rev more than 3000 rev thanks


Sounds like your vehicle is in limp mode. Check for faults with a fault code scanner at a local auto parts store. Resetting the fault will fix the limp mode, but not whatever caused your vehicle to initiate limp mode.

Sep 12, 2013 | Cars & Trucks

1 Answer

Vauxhall astra 1.7 code fault ecn 189554 going into limp mode


P1895 = Limp home mode - Limited performance
P1481 = Fan Control Circuit 1 - Open Circuit
P1482 = Fan Control Circuit 2 - Open Circuit

it could be there is an issue with the cooling fans on the vehicle, and the ECU is going into limp mode to prevent the engine overheating, or because the coolant temp is getting too high.

First, check all fuses are present and not blown.

Aug 28, 2013 | Cars & Trucks

2 Answers

When I accelerate hard to pass my check engine light comes on and the vehicle goes into limp home mode.


Get the vehicle looked at by a garage. The reason it goes into limp home mode is to protect the engine from further damage. The reason the check engine light comes on is because the engine needs checking with some urgency.

Nov 18, 2012 | 2007 SsangYong Actyon 4x4

1 Answer

2006 Ford Freestyle wrench light comes on and goes into limp home mode how do you fix


There is no way to get around a proper repair on a computer controlled transmission, that is wishful thinking. What is the fault code that is memory? Have you even run the system scan yet?

Apr 23, 2012 | 2006 Ford Freestyle

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...