Question about 2002 Ford Explorer

Open Question

Oem number P1000 diagnostic code ABS light on

ABS light on, OEM diagnositic code P1000, monitor testing not completed. The ECM performs system monitoring testing, this code indicateds a monitor has not completed. Probable cause codes cleard or battery disconnetcted. What does all this mean?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 113 Answers

SOURCE: ford dtc po1000

try unhooking ur battery for 30 min

Posted on Jun 16, 2008

Ad
  • 3 Answers

SOURCE: Have random cylinder misfire, Diagnostic

check your coil I just replaced one because of the same problem

Posted on Jan 04, 2009

chrischronic
  • 235 Answers

SOURCE: 1997 FORD CODE P1000

a p1000 code means that the system has not run all checks since last memory erase. in other words after a code erase this code is set until the car has been driven for 2 drive cycles which is 20 to 25 miles then 20 to 25 miles again.

Posted on Apr 21, 2009

  • 80 Answers

SOURCE: 2002 Ford Ranger check engine light indicating misfire

Code P0301
Ignition Coil Pack
Ignition Cable
Spark plug
Clog or dirty fuel injector
Evap canister purge valve
Engine Compression
fuel pressure

you have 3 type of engine for your truck
2.3L 4 cylinder
3.0L 6 Cylinder
4.0L 6 Cylinder

need to know that type Engine

The reason why the service light come on because it is a hard code
not a soft code.

Let me know

Posted on Sep 20, 2009

TittyMonster
  • 13 Answers

SOURCE: ford focus wont start no spark changed coil and

sounds like your main computer has gone bad,the error code means it cant read the CPU, buy a used one from the junk yard with a return policy, If that does not get the car running you can return it..It should be located in the lower right side of the dash, behind the glove box

Posted on Feb 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do codes P0411, P1000


P1000 code means the codes were cleared or the battery was disconnected
Powertrain Control Module (PCM) Reset Description All OBDII scan tools support the powertrain control module (PCM) reset.
The PCM Reset allows the scan tool to command the PCM to clear all emission-related diagnostic information. When resetting the PCM, a DTC P1000 will be stored in the PCM until all the OBD II system monitors or components have been tested to satisfy a drive cycle, without any other faults occurring. For more information about a drive cycle, refer to Drive Cycles .
The following events occur when a PCM reset is performed:
  • Clears the number of Diagnostic Trouble Codes (DTCs).
  • Clears the DTCs.
  • Clears the freeze frame data.
  • Clears diagnostic monitoring test results.
  • Resets status of the OBD II system monitors.
  • Sets DTC P1000.

P0411 Secondary Air Injection System Incorrect Flow Detected

neither of these could cause a no start or no crank problem . Is the battery good an do you have good connections on the battery ? Do the headlamps show bright when on ?

Oct 14, 2015 | 1997 Lincoln Continental

1 Answer

Retrieved codes P0191, P0152, P1246, P1233 and P1000 on my 02' Taurus 3.0 OHV. What would be the most likely culprit causing these codes?


P1000 - Monitor Testing Not Complete The on board diagnostic II (OBD II) monitors are performed during the OBD II Drive Cycle. The DTC will be stored in continuous memory if any of the OBD II monitors do not complete.
  • Vehicle is new from the factory
  • Battery or PCM had recently been disconnected
  • An OBD II monitor failure had occurred before completion of an OBD II drive cycle
  • PCM DTCs have recently been cleared with a scan tool
  • PTO circuit is shorted to VPWR or B+ or PTO is on during testing
The DTC does not need to be cleared from the PCM except to pass an inspection/maintenance test

Aug 04, 2015 | 2002 Ford Taurus

2 Answers

My car won't start and is showing a p1000 code . What does this mean?


P1000 is a manufacturer specific fault code:

Ford P1000: OBDII Monitor Testing Not Complete.
Jaguar P1000: Engine control module (ECM) - internal error.
Kia P1000: System diagnosis incomplete.
Land Rover P1000: Engine control module (ECM) memory erased - no codes stored.
Mazda P1000: OBDII Drive Cycle Malfunction.

So depending on the manufacturer of your car would depend on the meaning of a P1000 code!

Jan 21, 2015 | Cars & Trucks

1 Answer

Light abs traction control stays 1998 buick park avenue


PRE-DIAGNOSTIC INSPECTIONBefore diagnosing ABS/TCS, perform a comprehensive visual inspection of system as follows.Check ABS/TCS wiring harness connectors for looseness. Check harness routing; pay particular attention to wheel speed sensor wiring harness routing. Check fuses No. 1D, 5B and 6B in instrument panel fuse block. Check fuses No. 1 and 2 in underhood fuse block. Check brake fluid level in master cylinder reservoir. Check brake fluid level in Pressure Modulator Valve (PMV) assembly reservoir. Ensure parking brake is fully released. Ensure parking brake switch is functioning properly. Always perform ABS/TCS system functional check before using DIAGNOSTIC CODE CHARTSThe EBCM/EBTCM has self-diagnostic capability, which can detect system failures. Fault codes stored by EBCM/EBTCM can be displayed using Tech 1 scan tester. There are no provisions for flash code diagnostics.Begin ABS/TCS diagnosis with PRE-DIAGNOSTIC INSPECTION procedure. If failures are found during pre-diagnostic inspection, perform necessary repairs, and proceed with ABS/TCS FUNCTIONAL CHECK. See Fig. 5 .If no failures are found during pre-diagnostic inspection, go to ABS/TCS FUNCTIONAL CHECK. See Fig. 5 . The ABS/TCS FUNCTIONAL CHECK will either indicate ABS/TCS is functioning properly or direct technician to various diagnostic procedures such as diagnostic charts, symptom diagnosis or BRAKE warning light diagnosis.CHART D - TRACTION OFF WARNING LIGHT ON CONTINUOUSLY & NO DTC SET (BUICK WITH UH8 OR U2A INSTRUMENT CLUSTER)Circuit DescriptionWhen ignition switch is first turned to RUN position, EBTCM goes through a self-test, which lasts 2-4 seconds. During self-test, EBTCM commands TRACTION OFF indicator warning light on. Powertrain Control Module (PCM) can also command EBTCM to set a Code 75 which will illuminate TRACTION OFF indicator.Traction control switch is located either on instrument panel center trim plate or driver's front door trim panel. Switch allows driver to select traction control mode (on/off). When traction control system is turned off, TRACTION OFF warning light comes on.EBTCM monitors transaxle temperature through

Jul 12, 2014 | 1998 Buick Park Avenue

1 Answer

2002 jaguar x tipe code P1000


this code relates to monitoring the ECU self test , meaning it was'nt completed , have the code cleared , are there any problems with the vehicles performance or just the CEL on ? follow this link and you can run the self test your self to see if that sorts the prob
Jaguar Type Instrument Cluster Diagnostic codes

Apr 25, 2014 | 2002 Jaguar X-Type

1 Answer

Radio code


OBD system tests
Possible fault codes:
P1000 OBD system tests Operation not
completed
Setting of the fault code P1000 has no
influence on the system <Engine
management>, smooth running or performance
as long as it is automatically erased
whilst driving.
The fault code P1000 indicates noncompletion
of system tests.
* Misfire detection
* Evaporative emission control system
* Exhaust-gas recirculation
* Lambda sensor
* Exhaust gas catalytic converter
The fault code P1000 cannot be erased. It
is cancelled automatically once the
vehicle has completed certain driving
cycles.

Jul 27, 2013 | 2007 Ford F

1 Answer

Wats the code p1000 on my 2002 jaguar x type


P1000 JAGUAR - On Board Diagnostic System Readiness Test Not Complete, this is known as the OBD2 drive cycle.


Possible causes - The vehicle is new from the factory.
- Battery or Powertrain Control Module (PCM) had recently been disconnected.
- An OBD monitor failure occurred before completion of an OBD drive cycle.
- PCM Detected Trouble Codes (DTC) have recently been cleared with a scan tool.
When is the code detected? If DTC P1000 is triggered after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles have not been cleared. P1000 JAGUAR Description The On Board Diagnostic (OBD) monitors are performed during the OBD Drive Cycle. P1000 is stored in continuous memory if any of the OBD monitors do not carry out their full diagnostic check.

Feb 18, 2011 | 1999 Jaguar XK8

2 Answers

P1000 code appeared. just replaced alt. recharged batt. wont start.


The definition for P1000 code is as follows:
OBD II Monitor Testing not complete
You may be experiencing ECM computer problems. Have it diagnosed by a certified ASE professional.

Feb 06, 2011 | 1998 Jaguar XK8

2 Answers

Fault code P1000 [18,2,10,0],Ford Fiesta 2005


P1000 means that you or someone has disconnected the battery,and the car has not been driven far / long enough for the computer to relearn its stratagies.
Engine light could be the fault of the speed sensor, or wiring to the sensor.

Jul 13, 2009 | 2007 Ford F

Not finding what you are looking for?
2002 Ford Explorer Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5627 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...