Question about Cars & Trucks

Open Question

TOYOTA AVANZA 1.3 TORQUE SETTING FOR CYLINDER HEAD

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

Ad
  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Pelukes01
  • 52 Answers

SOURCE: what are the cylinder head torque settings for a

0900c1528006efe6.jpgUmiformilly tighten each of the ten head bolts in several passes, in the sequence shown. Tighten them to 44 ft. lbs. (60 Nm).

Posted on Jul 23, 2010

  • 496 Answers

SOURCE: I need the torque settings

cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Posted on Feb 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi hope some one can help me I need the torque settings for a 1.5 toyota avanza. Mains big ends and cyl head pls


Call a machine shop or do a google search or join and search a toyota forum.

Aug 31, 2014 | Cars & Trucks

1 Answer

Hi I need the torque settings for both the cylinder head and the bottom end bearings for a 1997 Toyota Prado (3.4litre petrol). Thanks


1997 Toyota Prado 5VZ-FE
Cylinder head bolts:

Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Feb 27, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Hi. I am assembling a avanza 1.3 that blew head gasket. What are the torque settings for head bolt


I don't have the specs.Evenly go around to all of the head bolts and gradually torque them. 20,40 60 foot pounds.
Depending on the type of gasket you used,you may have to re-torque the bolts after it has gone through one heat cycle.

Mar 08, 2013 | 2007 Toyota Avanza 1.3

1 Answer

Cylinder head 2.4 torque


step 1 58 ft lbs.

step 2 additional 90 degrees

1_10_2012_5_41_54_pm.jpg

Jan 10, 2012 | 2003 Toyota Camry

1 Answer

Hi i was wanting to now if anyone knows the Torque Settings for the head of a 1992 Toyota Windom V6. Thank you.


Cylinder Head Torque Sequence

Tightening torque:
12 sided bolt
Step 1 ..... 34 Nm (25 ft lb)
Step 2 ..... Tighten an additional 90°
Step 3 ..... Tighten an additional 90°
Recessed head bolt ..... 18 Nm (13 ft lb)

02e7fe1.gif

f910c49.gif

Oct 21, 2010 | Toyota Passenger Cars & Trucks

1 Answer

Head bolt tourqe settings on a toyota cressida


Cylinder head bolt removal sequence


Removal sequence: Front 3 7 11 13 10 6 2 1 5 9 14 12 8 4

***CAUTION*** The above sequence must be followed during removal as to avoid warpage of the cylinder head unit

Reverse sequence to install, Step 1: Torque to 10 Ft/Lbs Step 2: Torque to 18 Ft/Lbs Step 3: Torque to 25 Ft/Lbs Step 4: Turn an additional 90 degrees Step 5: Turn an additional 90 degrees Step 6: Torque the 2 recessed 8mm bolts to 13 Ft/Lbs *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper Torque

Don't forget to rate this answer, Good Luck

Apr 24, 2010 | 1992 Toyota Cressida

1 Answer

Toyota windom v6 head bolts torque settings


INSTALL CYLINDER HEAD if any bolts broken or deformed , replace it.

7------2-----4--------6
5------3-----1--------8
FRONT sequence head bolts
8-------1-----3-------5
6-------4-----2-------7

CYLINDER HEAD bolts are tightened in three progressive steps
1. 34 Nm ( 25 ft.lb)
2. 90 degree
3. another 90 degree.

double check everythings before install the head,
be sure to install the GASKET correctly.

Hope this can help.

Apr 19, 2010 | 1993 Toyota Camry V6

1 Answer

Need torque settings for 1985 4A corolla cylinder head


hey, torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:

9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Jan 14, 2009 | 1985 Toyota Corolla 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

543 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...