Question about Hyundai Cars & Trucks

Open Question

I need to adjust the valve clearance can you please give me a firing order of Hyundai Starex model 1997

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: valve clearance

metric - inlet and exhaust .15 (engine cold) .25 (engine warm)

Posted on Nov 07, 2008

Ad
dmfixit
  • 226 Answers

SOURCE: firing order on engine 1997 cavalier 2.2

Firing order 1-3-4-2
engine ----- coils ----
l 1 l l 1 4 l
l 2 l l 2 3 l
l 3 l
l 4 l

Posted on Jan 08, 2009

  • 1 Answer

SOURCE: Valve tappet adjustment

well, I can see ur message has been here for quite some time. Most probably you got the answer to ur request.
I just did the valve clearance on the engine of my SJ413 that has the 1000cc engine of an SJ410 :
When cold: 0.13mm Intake and 0.18mm Exhaust
Engine sounded well and worked fine after that.
Enjoy
Mehdi

Posted on Feb 07, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: noisy startup when cold, sounds like valve

Hello onarock844...The Hyundai 2.4 litre and the 3.3 litre are known to have valve train noise. Some sooner than others.
The timing chain tensioners on the 06 and 07 Sonata 3.3 engines built before August 4, 2006 are well known for developing wear that allows them to make a tapping or rattling noise for a short time after a cold start. This noise can be mistaken for a lifter noise, although the actual source is in the front cover area of the engine. Hyundai has released a technical service bulletin on this problem, which describes installation of an updated design timing chain tensioner (part #24410-3C300) to correct this noise issue.
Ask your dealer to refer to Hyundai service bulletin #06-20-002 for information...If this has already been corrected,,,and the noise is coming from the upper engine area and not from the timing chain area, then the valve clearance will need to be adjusted. This is done by disassembling the valve train and installing slightly different size tappets to change clearance.
This is a fairly labor intensive process, so if you are still under factory warranty then you will want to go over the dealer's head and get the Hyundai zone rep involved to get it covered before your warranty coverage expires...
I recommend useing a full synthetic engine oil, i know in a few cases where the noise has stopped when the oil was changed over to synthenic, also a high quality filter is important, such as a purolator.
Good luck...i hope this helps...please rate me a fixya.

Posted on Jul 29, 2009

ZJLimited
  • 17970 Answers

SOURCE: 1997 honda civic firing order, 4 cylinder

1.6L Engines Firing order: 1-3-4-2 Distributor rotation: Clockwise.

cdd80c6.gif

I hope help you with this, remember rated this post. Good luck.

Posted on Aug 25, 2009

Testimonial: "Thanks, runs like a charm, now!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the clearance between the rocker arm and the valve spring in a GM 2.2L motor


there is no specification for what you want
the valve clearance is between the end of the rocker arm and the end if the valve stem
the stem end is proud of the spring retainer so if your rocker arm is touching the spring retainer , you have a big problem as for the procedure it is set out in the workshop manual but if you don't have a manual it can be done like this
you will need the firing order of the engine first
now adjust no 1 piston valves when the next piston to fire has the valves in the rock position
that is the exhaust valve just closing as the inlet is just opening a bit of movement of the crank makes either valve move up or down
adjust no 1 piston valves
now move on to the next piston to fire and adjust the valves that were rocking
follow that procedure until all the valves are adjusted
for example
on a 4 cylinder engine with a firing order of 1--3--4--2
bring up no 1 piston and adjust the valves when the valves on no 3 piston are rocking
next piston to fire is no 4 so adjust no 2 piston valves
next piston to fire is no 2 so adjust the valves when no 1 valves are rocking
the procedure is the same for engines with any number of cylinders

Oct 19, 2016 | Cars & Trucks

1 Answer

Setting valve clearances


360 with hydraulic lifters, the crankshaft wit a ratchet and socket to get each valve closed. When lifter is at bottom turn the valve adjuster out to where you have free movement then turn adjuster till the rocker arm touches the lifter, then turn the adjuster in three quarters of a turn, and that valve is adjusted. No other clearance is required on hydraulic lifters. Do this with each valve in turn as each piston comes to top dead center using the firing order as a guide. When #1 piston is up to top dead center, both valves are closed. Adjust intake and exhaust at this time. Then the next in the firing order. The firing order can be found on the intake as is each cylinder marked with it's number. If it were a Chevy small block, for example only, firing order is 1-8-4-3-6-5-7-2. I would bring # 1 cylinder up to top dead center on compression stroke by removing that spark plug and stick my finger in the hole and crank the engine till I felt my finger being pushed away with compression, then bring that piston up till the timing mark was on the "0" of the timing tab at drivers side of the harmonic balancer on the crank. Adjust both valves on #1 cylinder and then turn the crank until both valves of #8 cylinder were free moving at the rocker. Then to the next in order of fire. I would turn each adjuster out at least one full turn before starting this procedure, then adjust them in order of firing starting with #1. It isn't hard, just takes time to do it right.

Aug 12, 2014 | AMC CJ7 Cars & Trucks

1 Answer

Adjusting tappet clearance


If you have adjustable tappets bring the engine to top dead center no 1 piston firing The rocker will be on the back of the cam lobes. Inlet .010" hot exhaust .012" hot and then turn until next firing piston is in position. Go by firing order. I suspect that a 1997 model would have hydraulic adjusted tappets which means no manual adjustment. If it is rattlly I would be checking for worn rocker shaft and rocker bushes.

Apr 02, 2013 | 1997 Nissan Pickup

1 Answer

I need the required valve & inyector clearance on a M11 engine


Cummins M11

Intake valve clearance 0.010 inch
Exhaust valve clearance 0.024 inch

The firing order is 1-5-3-6-2-4 and that is the order the valves should be adjusted started with first timing mark on main pulley adjust cylinder number 1 The valves and injector should be adjusted at the same time The crankshaft is then rotated 120 degrees to next timing mark and cylinder 5 is adjusted, the crank is rotated again 120 degrees to next timing mark and cylinder 3 is adjusted.then back to the first timing mark, cylinder 6 is adjusted, etc/

Adjusting nut on plunger should be adjusted to the point where you feel the plunger just reaches the bottom.of travel/bottoms out.

Feb 15, 2012 | Cars & Trucks

1 Answer

How to remove the headlight of hyundai starex 2000


can you give me instruction on how to remove the headlight assemble of Starex CRDI 2006 model

Feb 15, 2012 | Cars & Trucks

1 Answer

Want to know what the valve clearances are for my 1999 hyndai excel


Adjust the jet valve clearance before the adjustment of the
intake valve clearance.
Jet valve clearance (hot engine)
[Standard value]. . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

now adjust valve clearance
Valve clearance (hot engine) [Standard value]
Intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.15 mm (0.006 in.)
Exhaust. . . . . . . . . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

Jul 30, 2009 | 1990 Hyundai Excel

1 Answer

Valve clearance


these are hydraulic valves, no adjustment needed, with both valves fully open u back them off until they (rocker arms) are just slightly loose, then tighten them 1/2 turn, follow the firing order of the engine and bring it to top dead center (compression stroke) for each cylinder.

Jan 13, 2009 | 1997 Chevrolet Malibu

1 Answer

How do you adjust aftermarket roller rocker arms


well first you need to know the firing order...if it's a small block chevy the firing order is 18436572. You need to write the second four digits underneath the first four digits.

so it looks like this 1843
6572

This will let you know which rocker to adjust...turn the engine over by hand using a rachet on the crank shaft bolt by the harmonic balancer until you get both rockers for number 6 cylinder moving at the same time. Now you may adjust the clearance for both rocker for number 1 cylinder. Then crank the engine over by hand again until number 5 cylinder rockers start to move. Now you can adjust the clearance on number 8 cylinder. You will need to know the manufacturer specs for the valve clearance...continue until all rockers have been adjusted.

Note: The engine should be warm when you make the adjustment.

please rate this.

Sep 20, 2008 | Chevrolet Camaro Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...