Question about 2005 Nissan Altima
Procedure of how to change the transmission fluid
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
change the oil put 3 liter start the car leave it running untill warm check the oil level add if needed go road test it recheck the level at the end you probably gonna put 4 to 4.5 liter of trany oil that about the amounth of oil when you drop the pan or just unscrew the plug a complete overhaul is 8 to 9 liter hope it help fixya our post thanks pierre
Posted on Jul 13, 2008
their a red round circle that u pull on it just like the one from the oil exept the eng oil stick is yellow is usaly located close to the fire wall
Posted on Mar 06, 2009
frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!
Posted on Apr 23, 2009
Try this, Since you are applying the hand brake. Manually pull up on the emergency pedal and see if the light goes out. If this does work then you could have one of several problems. but, I am thinking that you might be able to adjust the brake tensioner if this car has one.
Posted on Jul 05, 2009
thats why you have to remove the frame and for this you need an engine support and the average mechanic will charge you arround 100 bucks to do it
some rental stores have them some dont good luck eithor way you go but for god sake be carefull
Posted on Dec 31, 2009
Tips for a great answer:
May 09, 2014 | 2009 Hyundai Azera
Jul 03, 2013 | 2008 Nissan Altima
Aug 11, 2011 | 2005 Nissan Altima
Mar 26, 2011 | 2005 Nissan Altima
Jan 03, 2011 | 2001 Nissan Altima
Dec 31, 2009 | 2005 Nissan Altima
Jun 20, 2009 | 2004 Nissan Altima
286 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: