Question about 2004 Dodge Ram 1500

Open Question

Replace emergency brake 2004 dodge ram - 2004 Dodge Ram 1500

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: brake pad replacment on 2004 Dodge Ram 1500

Remove two bolts holding caliper on and pull up as hard as you can on the caliper. Wiggling back and forth at the same time helps.

Posted on Aug 02, 2008

fgainer
  • 54 Answers

SOURCE: 2004 dodge ram 1500 rear brake light out how to replace?

Open up the tail gate, you will see two torque screws on the inside beside the tail lights. take these out, this will free up the housing and you can change it from there.

Posted on Feb 01, 2009

  • 840 Answers

SOURCE: passanger side mirror replacement on 04 dodge ram 1500?

very easy take the mirror inside cap off if you can not get to the 3 bolts then you will have to take trim panel off to take trim panel off look for plastic caps take them out and unscrew them then pop out the bottom of the door and pop the sides out then lift up and out should be loose enough for the bolts now/ 10mm bolts 3 Please rate my response thank you very much

Posted on Feb 02, 2009

  • 1 Answer

SOURCE: 2001 dodge ram 2500 abs light stays on and soo doe

I had the same problem and it turned out to be one of the front speed sensors and the rear speed sensor as well. If you get a chance to look at all the speed sensors make sure the wires on the front aren't burnt from hot brakes. I have an 01 3500 4X4 and it was a pain to change the front sensor but the rear sensor took about 5-10 minutes, it's located in the middle of of the rear axle right on top. I bought both of mine on Ebay and cut the price in half.

Posted on Aug 22, 2009

  • 236 Answers

SOURCE: 03 Ram 1500 E-Brake light flashing

its possible the switch on the e/brake unit broke, take a flashlight and locate a single/double wire that goes to the e/brake assembly (this is the piece you depress with your left foot) and look to see if the wire is broken or the switch the wire goes to is broken.

Posted on Dec 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Emergency brake light stays on


Bad sensor for the emergency brake switch. I had the same thing happened with my dodge

May 06, 2016 | 2006 Dodge Ram 1500

1 Answer

How to change parking brakes on 2003 dodge ram


  • 1 Determine which type of emergency brakes your Dodge Ram will need. Emergency brakes typically function by activating the regular braking system on the driving wheels. The emergency brakes for the Dodge Ram have used rear disc brakes since 2001.
  • 2 Release the parking brake pedal completely and raise your vehicle. Remove the tire and wheel with a socket wrench and disconnect the brake caliper from the caliper adapter. Slide the rotor from the axle shaft.
  • 3 Install the new brake rotor onto the axle shaft and complete the installation by reversing the removal steps.
  • 4 Tighten the wheel mounting nuts in the proper sequence with a torque wrench until the nuts are torqued to 47.5 foot/pounds Repeat the tightening sequence to torque the nuts to 95 foot/pounds.
  • 5 Apply and release the park brake pedal to seat and adjust the parking brake cables. Road test the vehicle to ensure the vehicle's brake system is functioning.
  • 6 Place tool C-3919 or the equivalent over the park brake shoes and use the star wheel adjuster to lower the park brake shoes until the lining just touches the jaws on the tool.


  • Read more : http://www.ehow.com/how_4521030_replace-emergency-brakes-dodge-ram.html

    Dec 31, 2014 | Dodge Cars & Trucks

    1 Answer

    I have a 2000 dodge ram 1500 v6. breaks feel spongy when applied


    this is an ongoing fault with dodge brakes that generally shows up after brakes have been slammed on in an emergency
    dodge refuses to address this problem .there are hundreds of complaints of this on the internet and nothing has been resolved

    Dec 16, 2010 | 2000 Dodge Ram 1500 Truck

    2 Answers

    03 Ram 1500 E-Brake light flashing


    its possible the switch on the e/brake unit broke, take a flashlight and locate a single/double wire that goes to the e/brake assembly (this is the piece you depress with your left foot) and look to see if the wire is broken or the switch the wire goes to is broken.

    Dec 15, 2009 | Dodge Ram 1500 Cars & Trucks

    1 Answer

    2004 Dodge Ram 1500 pickup speedometer and odometer quit


    I am having the same problem. I replaced the speed sensor on the rear diff. and the problem went away but when i started it the next day the problem came back. If you figure it out let me know.

    Oct 19, 2009 | 2004 Dodge Ram 1500

    1 Answer

    2002 ram 1500 brake and abs light on


    there should be adjustment under vehicle looks like bolt attached to cable just back off nut and loosen bolt 

    Oct 06, 2009 | 2002 Dodge Caravan

    1 Answer

    2004 emergency brake does the rotor need to be taken out


    What is the problem so far? You will find a rubber plug on the inside of the backing plate, you must loosen the auto matic adjuster in side before you can remove the disc, you will need to try either direction with a screwdriver once you find the correct direction ( you will feel the disc turn easier) continue until you can remove the disc. The replacing of the brakes after that is straight forward.

    Mar 14, 2009 | 2004 Dodge Ram 1500

    1 Answer

    Rear hub removal on a dodge 2004 ram 3500


    REMOVE THE RUBBER PLUG IN BACKING PLATE AND ADJUST E BRAKE SHOES DOWN TO REMOVE ROTOR

    Feb 15, 2009 | 2004 Dodge Ram 3500 Truck

    1 Answer

    Brake pad replacment on 2004 Dodge Ram 1500


    Remove two bolts holding caliper on and pull up as hard as you can on the caliper. Wiggling back and forth at the same time helps.

    Jul 13, 2008 | 2004 Dodge Ram 1500

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    186 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    75005 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7710 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...