Question about 2007 Dodge Nitro R/T

Open Question

2007 Dodge Nitro p0404

Hi. I am looking for detailed directions on replacing an EGR Valve on my Nitro. It is in a really bad place as far as there are bolts between the valve and the firewall that are hard to see/reach and I don't know how to remove them. Any advice greatly appreciated! Thank you Wendy

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: 2005 Dodge 1500 code p0404 EGR valve.

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the EGR selonoid fuse on a 05 Dodge Magnum 5.7L?


There is no solenoid fuse , the PCM - engine computer supply's the control voltage . You have a wiring problem ! http://www.obd-codes.com/p0404 Engine Code P0404 EGR Position Sensor Performance

Feb 25, 2016 | 2005 Dodge Magnum RT

1 Answer

EGR valve how to replace


Different on each engine. Buy shop manual for details and torque values.

Jun 17, 2015 | 2007 Dodge Nitro SLT

1 Answer

DODGE NITRO 4 LITRE EGR LOCATION 2007


The metal tube from the intake going behind the engine is going to the EGR Valve.


http://www.allpar.com/images/engines/4-V6-2.jpg

Apr 14, 2015 | 2007 Dodge Nitro

1 Answer

How to fix p0404 and p0420


code p0404 refers to exhaust gas recirculation (EGR) valve position--range/performance problem ===causes --hose leakage/blockage--wiring ---EGR valve/solenoid
code p0420 refers to cat converter system bank 1-efficiency below threshold===causes --cat converter---wiring---HO2S 2

May 31, 2014 | 2007 Dodge Grand Caravan SXT Minivan

1 Answer

Code p0441


po441 evaporative emission control system incorrect purge flow
po404exhaust gas recirculation control circuit range performance sounds like a dirty or bad egr valve

Sep 04, 2012 | 2007 Dodge Grand Caravan SXT Minivan

1 Answer

2004 dodge 1500 4 x 4 the engin mlight came on and the code is p0404. What does P0404 stand for?


SYMPTOM
P0404-EGR POSITION SENSOR PERFORMANCE

WHEN MONITORED
Engine running.

SET CONDITION
The EGR flow or valve movement is not what is expected.

POSSIBLE CAUSES
- Good trip equal to zero
- Excessive resistance in (F856) 5-volt supply
- (K34) EGR sensor signal circuit shorted to ground
- EGR assembly
- (K35) EGR solenoid control circuit
- Intermittent condition
- (K34) EGR sensor signal circuit open
- (K34) EGR sensor signal circuit shorted to ground
- (K900) sensor ground circuit open
- EGR assembly (ground)
- PCM
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i

May 28, 2011 | 2004 Dodge Ram 1500

1 Answer

2005 dodge caravan diagnostic code p0404, please explain and do i replace the egr valve?


p0404 is-egr flow ckt range/performance, check egr, remove from vehicle and clean out carbon from valve and where it mounts on engine. also check the wireing connector and wire to valve. if this dosnt work, replace valve,

Apr 23, 2010 | 2005 Dodge Caravan

1 Answer

Just replaced EGR valve- had code P0404. It's


First question, did you clean the port or passage out or the cyl head where the valve mounts to, when the valve was taken off of the engine? 2nd question, did you replace the Vacuum transducer ( little black round valve, with a vacuum hose fitting) and the valve assy? After these items have been replaced, it usually needs to have the PCM (powertrain control module) reset with a scanner of some type.

Mar 07, 2010 | 2004 Dodge Grand Caravan

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

Not finding what you are looking for?
2007 Dodge Nitro R/T Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...