Question about 2004 Chrysler Sebring

2 Answers

Installed a 2002 2.7 engin in my 04 sebring removed an 04 2.7 the car will not start no spark tried crank sensor still no start.

The old engin ran fine but the head was crack thats why i changed the motor please HELP

Posted by on

  • aj obrien Dec 07, 2012

    Still no spark thinking may have to install computer that was with the used engin i installed? Also i only have 2.7 volts at the coils is that enough? also if i change the computer do i have to reprogram.

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Chrysler Expert
  • 252 Answers

These engines come with different fly wheels and cam sensors. the flywheel has to have the same number of slots and the cam gear has to be the same as what the car came with or it wont start

Posted on Jan 08, 2015

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 95 Answers

Look into the coil pack id check wiring to the coil pack also

Posted on Dec 05, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 46 Answers

SOURCE: 2001 sebring will turn over but will not start

Most Chrysler cars do have an anti-theft system that can cut out the engine.

I would call the service department, with your VIN handy, and see if yours was equipped with one, and what you need to reset it.

If that isn't the problem, your EGR valve might be bad, or the sensor for it. I've seen a lot of cars where if either the valve itself, or the sensor are malfunctioning, the car won't run properly.

I would also check your MAF and IAC, as those can cause the car to not run.

If you can, get an OBDII code scanner, and pull the codes from your car, they might give you a more specific place to look. (Most parts stores will let you take one home, you put a deposit down, and get it back when you bringthe scanner back to them)

Posted on Dec 04, 2008

chryslertech
  • 115 Answers

SOURCE: 2000 Chrysler Concorde

These engines are known for the water pumps and/or the timing chains hydraulic tensioner failing and causing the timing to jump time. And checking the timing on these engine is not easy unless you can get a scan tool that can tell you if the cam and crank are in sync. If it says out of sync it has most likely jump time.

Posted on Feb 16, 2009

csmock132
  • 4669 Answers

SOURCE: Crank sensor and camshaft sensor

The crank sensor is in the top of bell housing of the transmission towards the back of the engine compartment. The cam sensor is built into the distributor.

Posted on Mar 07, 2009

t1randa
  • 27 Answers

SOURCE: 1996 Chrysler Sebring Conv.- Power Drain or Damaged Crank Sensor?

try checking the secondary ground wire that comes off the battery see if its loose or corroded might help

Posted on May 29, 2009

WonderTech
  • 268 Answers

SOURCE: told the chrysler sebring crank sensor needs

Because it's on the back of the transmission bell housing, where the transmission and engine meet, it is very difficult to replace. I have replaced one and also had a dealership replace them. The transmission was not removed. I would recommend taking it to a repair shop where they have the proper tools for this repair/replacement. It will cost around $300.00. Call around for prices.

Posted on Aug 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 Chrysler Sebring cranks and won't start. I have changed the plugs, wires, and distributor. I have a 3.0 engine


Standard practice is check for spark at each plug when you crank. If you're getting spark, then check for fuel getting to cylinders.

Feb 06, 2017 | 2004 Chrysler Sebring

1 Answer

Trying to find out where the crankshaft sensor is located on Mazda Tribute 2002? Need to change it


2004 Mazda tribute 2.0l manual transmission cranks position sensor tip worn / rubbing. p0351, p0352, p0500, p0320 codes. I have a 2004 Mazda tribute with 2.0l 4 cylinder. 140,000 miles. First problem was it would not start but I could hear the fuel pump run and the engine cranked over. I checked for spark and all four plugs had no spark. p0351, p0352, p0500, and p0320 codes displayed.
I have 12 volts at coil. I decided to remove and inspect crank sensor on the transmission side of the engine ( on engine below thermostat housing bolted to engine block) once i removed it i noticed the tip of the sensor was broken, yes, broken. so I knew i found the problem.
I put a new crank sensor in and the car started but ran for 1 hour idling as if a cylinder was not firing. Then it would not start ever again. I removed my brand new replacement sensor to find the tip was rubbed off enough to see the inside metal. i think it could be a possible warped flywheel but I am having trouble finding diagrams of the excitation part of how the crank position sensor works.
I believe the flywheel has holes that excite the sensor. The tribute does move and clutch works for the hour I had it running, so the manual Trans does work as well as the clutch.
https://electronicshelponline.blogspot.com/

Jul 16, 2016 | 2002 Mazda Tribute

1 Answer

2000 Sebring with 2.5 engine. Cranks but won't


try the ignition control module in the distributor

Nov 11, 2012 | Cars & Trucks

1 Answer

2002 sebring won't start


crank shaft position sensor

Sep 23, 2012 | 2003 Lexus LS 430

5 Answers

2002 Jeep Liberty 3.7L Engine Swap to newer 2004 engine


Has anyone made this work yet? I have the same problem 2002 jeep 3.7 and just installed a 04 motor. Timing is off. Some one had a good idea of mounting the crank gear to the out side of the harmonic ballancer and mounting the sensor with a bracket. What about the cam gear on the left side. Does the timing cahain have to come off to remove it? Or has any one swaped the wiring harnest, and computer.
Please email me back. pcardoso@cogeco.ca Thanks for your help.

Jun 25, 2009 | 2002 Jeep Liberty

1 Answer

2000 sebring won't start


Crank Sensor is the likely issue. It does not throw a code. Key indicator is the call stalls all the time. R&R sensor.

Apr 01, 2009 | 2001 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...