Question about 2005 Hyundai Sonata

1 Answer

Door chime and open door warning light won't turn off

Posted by on

  • 1 more comment 
  • Anonymous Mar 16, 2014

    Door chime won't turn off

  • Anonymous Mar 16, 2014

    Door chime won't turn off on my 1998 Lumina

  • Anonymous Apr 01, 2014

    Even when I drive

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

More than likely you have a bad door switch check the driver side first

Posted on Dec 05, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: 2004 Hyundai Elantra open door light comes on when braking

have you checked your brake fluid?

Posted on Mar 06, 2009

  • 366 Answers

SOURCE: Car won't start; radio & door chime work fine.

check ign. fuses,if ok,check wiring at starter,if ok,undo starter have it checked.replace if needed

Posted on Sep 27, 2009

  • 20 Answers

SOURCE: 2007 Hyundai Accent the driver side

Either the interior door handle or the cable inside the door is broken. You'll need to remove the door panel and look to see what is damaged.

Posted on May 25, 2011

bhowell786
  • 88 Answers

SOURCE: the remote battery died and after replacing it the

The remote needs to be programmed when the battery get's replaced. You will most likely have to take it to a dealer to have it done.

Posted on May 26, 2011

Testimonial: "thanks for your help i'll try that."

  • 219 Answers

SOURCE: Door chime will not go

manually check your door jam switches. They quite often break or rust up, once they rust they may as well be broken. Get some from your local car wreckers and change them out and see if that works.

Posted on Oct 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

7 dings and a beep when starting 2000 ford explorer? what does that mean


NOTE: The generic electronic module/central timer module (GEM/CTM) is connected to the ISO link and is diagnosed through the data link connector (DLC) with a scan tool.
There are five warning chimes and lamps the GEM/CTM controls: headlamps operating without the ignition on (chime only), door ajar (chime and lamp), key-in-ignition (chime only), driver seat belt warning (chime and lamp), and message center.


Audible Warnings Warning Condition Lamp Duration Audible Duration Audible Output Safety Belt 60 Seconds 6 Seconds Chime, 60/Min. 740 Hz Key In Ignition - Continuous Chime, 120/Min. 740 Hz Headlamps On - Continuous Chime, 240/Min. 740 Hz Door Ajar Continuous 1 Second Single Tone, 1000 Hz Message Center (Tone Request) - 1 Second Single Tone, 1000 Hz
When the is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
The will turn on for 60 seconds or until the driver safety belt is fastened. Both the chime and the lamp turn on at the same time.
If the safety belt is buckled before the ignition switch is turned to RUN or START, from OFF or ACC, neither the chime nor lamp will be activated.
Anytime the is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed or the safety belt is buckled.
When at least one door is ajar and the key is in the RUN position, the door ajar cluster lamp is activated and remains on until all doors are closed. A warning tone will sound once any time the key is in the ignition switch and any door is open.
The key-in-ignition warning will sound when the driver side is opened with the key in the and the in OFF or ACC. It will continue to sound until the key is removed, the is closed, or the is in RUN or START.
The headlamp-on reminder chime will be activated if the headlamps or parking lamps are on, the key is not in the ignition switch, and the driver door is opened.
A single tone will be provided each time a ground signal is received from the message center. A one-second tone will sound for warning indications from the message center. A 100 milli-second tone will sound for each message center button depressed.

Feb 12, 2015 | 2000 Ford Explorer Eddie Bauer

1 Answer

2005 jeep wrangler when i turn lights on beeping starts


did you RTM read the operators guide yet,
it tells you why all beeps beep and what lamps flash, (warning) and why. did you?
you turn on, the head lights, (what about 1st click , parking lights"?)
and does the dash cluster, show warnings of any kind?

if a door is ajar the system will think, you are exiting veh. with lights on and tell you, buy beeping ,etc.
but on my jeep it says on the dash DOOR, or on EVICs, (not yours)
the newer car even tells what door IS AJAR.
mine on shows , "DOOR"
the operator guide will say, check all doors for ajar, and get warning clear before driving....etc.

if you lost the guide here it is for free

http://justgivemethedamnmanual.com/jeep/jeep-wrangler-owners-manuals/

click the 05 link
ignore beeps, there are just too many .. i look at the cluster and learn to read it..
my newer jeep 08 can produce 1000s of errors,,,,, possible.
in fact the intent it to beep to tell the driver to look at the cluster
for in depth, causes.
see chapter starting on page 136'

once sound it makes is Check gauges chime. so check them.
and headlamps left on
and door ajar.

page 63
NOTE: If the driver's door is left open, and the headlights
or parking lights are left on, the "High Beam
Indicator Light" will flash and a chime will sound.
Lights-On Reminder
If the headlights or parking lights are on after the ignition
is turned off, a chime will sound when the driver's door

its a crude system, and evolved to complex in 2007.
"DOOR" or RF-door , on mine.
or

NOTE: A tone will chime if the turn signals are left on
for more than 1 mile (2 km).

search manual for
"chime will sound"

Mar 21, 2014 | 2005 Jeep Wrangler

2 Answers

Electrical problems


I would start with the fuses first. No I don,t believe they are but reading more into your problem I would check your alternator if not receiving the right amount of amp. output could and will make your computer go crazy. so check that first let me know how it goes good luck.

Aug 09, 2012 | 2000 Mazda Protege

3 Answers

Navigator Door Chime goes off when car off and I open the door. Radio system stays on & interior lights go off when door shuts.


All this comes from the GEM module,You will need to repair the driver door lamp switch located in the door lock assemble.

Mar 15, 2012 | 2003 Lincoln Navigator

1 Answer

The door chime on my 2003 oldsmobile alero won't stop chiming even though the car is off and the doors are all closed.


It is probably the body control module. It thinks you left the lights on or door open with key in ignition.

Aug 22, 2011 | Oldsmobile Alero Cars & Trucks

1 Answer

1998 Taurus SE warning chime beeps as you get in the driver door


Hi John,

Had a similar problem with my Saturn. Door chime going all the time, the seat belts going up - down - up for no apparent reason.

Turned out to be the switch in the door jamb had become unseated. As it randomly made and broke contact, the cars computer thought the doors were opening and closing, then acted accordingly.

I remounted it with the help of a hot glue gun (plastic mount).

Hope this info helps with your problem.

Best regards
Mike

Aug 03, 2009 | 1996 Ford Taurus

2 Answers

Possible ignition switch problem? 99 Explorer


key chime sounds if the little tab is grounded where the key contacts it. The theft light is supposed to blink when the system is armed to let you know it is armed. That's normal.

What do you mean by auto door locks won't unlock? The remote doesn't work? the door lock/unlock button on the door trim panel? Do they lock ok? Or, just unlock doesn't work?
-----------------------------------------------------------------------------------------------

NOTE: The generic electronic module/central timer module (GEM/CTM) is connected to the ISO link and is diagnosed through the data link connector (DLC) with New Generation STAR (NGS) Tester.
There are five warning chimes and lamps the GEM/CTM controls: headlamps operating without the ignition on (chime only), door ajar (chime and lamp), key-in-ignition (chime only), driver seat belt warning (chime and lamp), and message center.


Audible Warnings Warning Condition Lamp Duration Audible Duration Audible Output Safety Belt 60 Seconds 6 Seconds Chime, 60/Min. 740 Hz Key In Ignition — Continuous Chime, 120/Min. 740 Hz Headlamps On — Continuous Chime, 240/Min. 740 Hz Door Ajar Continuous 1 Second Single Tone, 1000 Hz Message Center (Tone Request) — 1 Second Single Tone, 1000 Hz
When the is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
The will turn on for 60 seconds or until the driver safety belt is fastened. Both the chime and the lamp turn on at the same time.
If the safety belt is buckled before the ignition switch is turned to RUN or START, from OFF or ACC, neither the chime nor lamp will be activated.
Anytime the is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed or the safety belt is buckled.
When at least one door is ajar and the key is in the RUN position, the door ajar cluster lamp is activated and remains on until all doors are closed. A warning tone will sound once any time the key is in the ignition switch and any door is open.
The key-in-ignition warning will sound when the driver side is opened with the key in the and the in OFF or ACC. It will continue to sound until the key is removed, the is closed, or the is in RUN or START.
The headlamp-on reminder chime will be activated if the headlamps or parking lamps are on, the key is not in the ignition switch, and the driver door is opened.
A single tone will be provided each time a ground signal is received from the message center. A one-second tone will sound for warning indications from the message center. A 100 milli-second tone will sound for each message center button depressed.
------------------------------------------------------------------------
  1. NOTE: The generic electronic module (GEM)/central timer module (CTM) must be reconfigured upon replacement. Refer to the New Generation STAR (NGS) Tester help screen on the configuration card to program the Tire Size, Axle Ratio.
    The power windows system and rear window defroster system are (GEM) controlled systems.
----------------------------------------------------------------------------------------------
  • All Windows Operate With the Ignition in the OFF Position
  • Circuitry.
  • Accessory delay relay.
  • CHECK the accessory delay relay; REFER to Component Test. If OK, REPAIR circuit 400 (LB/BK). If not OK, REPLACE the accessory delay relay. TEST the system for normal operation.


-------------------------------------------------------------------------
report back

May 06, 2009 | 1999 Ford Explorer

1 Answer

Warning bell won't stop sounding


Section 13-09: Gauges, Warning Devices — Chime System 1996 Windstar Workshop Manual
DESCRIPTION AND OPERATION Warning Chime Systems Three distinct sounds are used to indicate the area of concern. Seat belt warning generates 1 chime per second
key-in-ignition generates 2 chimes per second
headlight on generates 4 chimes per second.
Key-In-Ignition Warning The key-in-ignition warning will sound when the driver's front door (20125) is opened with the key in the ignition switch. It will continue to sound until the key is removed, the front door is closed, the ignition switch is turned to START or the vehicle speed is over 24 kmh (15 mph).

Safety Belt Warning When the ignition switch is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
  • The safety belt warning indicator lamp (10C859) will activate for 60 seconds or until the driver's safety belt is fastened. Both the chime and lamp activate at the same time.
Anytime the ignition switch is released from START and returns to RUN while the safety belt lamp or chime is activated, the safety belt warning lamp or chime will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Headlamp Switch On Warning The chime will be activated if the headlamps or parking lamps are ON, the key is not in the ignition and the driver's door is opened. The chime will sound at a rate of four per second.

Apr 23, 2009 | 1996 Ford Windstar

1 Answer

Key on engine running trouble code 55


Warning Chime Systems The generic electronic module (GEM) will sound the following warnings:
  • key-in-ignition warning
  • safety belt warning
  • headlamp switch ON warning
  • door ajar warning
------------------------------------------------------------------------------------------------
Headlamp Switch On Warning The generic electronic module (GEM) sounds when the driver door is opened while the headlamp switch (11654) is in the PARK or HEAD position, and continues to sound at a rate of 4 chimes per second until the headlamp switch is turned off or the driver door is closed.
  • When the headlamp switch is in the PARK or HEAD position, power is supplied through Circuit 293 (O/R) to the GEM.
  • When the driver door is open, the driver door open warning lamp switch (10B997)is closed and ground is supplied to the generic electronic module (GEM).
A delayed headlamps on repetitive chime will sound for a period of three seconds beginning twenty seconds after the key is turned to OFF, LOCK or ACC, the headlamp switch is in the PARK or HEAD position, and the driver door is closed. Delayed headlamps on is terminated by opening and closing the driver door again.
---------------------------------------------------------------------------------------
Door/Liftgate Ajar Warning The door/liftgate ajar warning functions as follows:
  • The generic electronic module (GEM) sounds a warning tone for one second when any vehicle door, liftgate window or the liftgate is ajar without any other door already open and the ignition switch is in the RUN position.
  • Power is then supplied through Circuit 627 (BK/O) to the door ajar warning indicator lamp which remains illuminated until all doors are closed or the ignition switch is no longer in the RUN position.
----------------------------------------------------------------------------------------------
Key-in-Ignition Warning The generic electronic module (GEM) sounds when the LH front door is opened with the key in the ignition switch and continues to sound until the key is removed or the door is closed.
  • When the key is in the ignition switch, the ignition key warning switch terminal and wire (11A128) is closed and ground is supplied through Circuit 158 (BK/PK) to the generic electronic module (GEM).
  • When the LH front door is open, the LH front door open warning lamp switch (10B997) closes and ground is supplied through Circuit 57 (BK) to the generic electronic module (GEM).
-------------------------------------------------------------------------------------
Safety Belt Warning When the ignition switch is turned to RUN or START from the OFF or ACC position and remains in RUN or START, the chime will sound for six seconds or until the safety belt is buckled. The safety belt warning indicator lamp (10C859) will turn on for 60 seconds, or until the LH front safety belt is fastened. Both the chime and lamp activate at the same time. If the safety belt is buckled when the ignition key is turned to RUN or START from OFF or ACC, the lamp will prove out for two seconds, but chime will not be activated. Any time the key is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Feb 25, 2009 | 1999 Ford Taurus

1 Answer

Warning chime continues to chime as I drive


My guess is a faulty switch at door for turning off interior lights/door closed, which is giving chime that door is still open

Dec 10, 2008 | 1997 Ford Mustang Cobra

Not finding what you are looking for?
Cars & Trucks Logo

634 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...