Question about 1998 Chevrolet K3500

1 Answer

How to get hub off to replace brake rotor on 1997 k3500 chevy

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers

Smack rotor with hammer

Posted on Jun 10, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 33 Answers

SOURCE: cannot get the hub off to replace rotors

the rotors should be on the hub behind the wheel... you will have to remove the brake caliper and it should just pull off... may be a few clips on the wheel stud

Posted on Nov 06, 2009

REDOIL
  • 355 Answers

SOURCE: are the brake rotor and front hub one piece or can

NO YOU NEED TO REPLACE AS ONE ROTOR AND HUB

Posted on Aug 13, 2009

Ninja_Rick
  • 119 Answers

SOURCE: replace front brakes and rotors

first take off wheels, then check if it is a star screw or a normal bolt, then remove the bottom bolt, remove the top bolt, and take the caliper off to access the pads and to remove the rotors, then back together the way it came apart with some anti seize on the face and bolts. Sometimes you have to pound the old rotors off...

Posted on Mar 08, 2010

  • 110 Answers

SOURCE: K3500 hydraulic brake booster engages brakes when

hello there:
You will need to replace the brake booster to correct the problem in order to do this you will need to remove the push rod from you're brake arm separate the master cylinder from the booster and remove the four bolts on the booster and slide it out install in reverse hope this help you out sincerely D.Jones

Posted on Jun 12, 2010

  • 47 Answers

SOURCE: need to replace rear brakes on 1997 chevy blazer

disk or drum?

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removeing front hubs on 1997 k3500 chevy


Some vehicles windshield are secured only by screws, others require windshield knives, and a windshield tool kit.


--------------------------------
obd2express.co.uk

Dec 05, 2012 | Cars & Trucks

1 Answer

Removing the front rotors on my k3500 chevy truck


if you took the tire, brake caliper and everything off and you are replacing the rotors then spray some wd-40 or pb blaster around the lug nut bolts and the center and let it set and work into it. if you cant wiggle it off then take a regular hammer and smack the back of the rotor. sometimes the rust and brake dust will build up and cause it to stick.

Apr 10, 2012 | Chevrolet 3500 Cars & Trucks

1 Answer

How do you change the front passenger side wheel bearing on a 1997 Chevy Blazer 4 wheel drive? Need detailed instructions.


Once the truck is on jack stands remove the brake caliper and rotor. The hub assembly should slide right off at that point. The wheel bearings are actually sealed in the hub assembly which is kind of nice because then you don't have to deal with grease packing the bearings. Just slide the new hub assembly back on. Put the rotor and caliper back together and you should be good to go. Hope this helps you.

Feb 12, 2011 | 1997 Chevrolet Blazer

1 Answer

After removing the tire, there is a hub type assembaly that appears to be bolted onto the rotor, after plenty of PB oil and some TLC, i managed to break this assembaly free, so i thought i was home free,...


K3-Series

Raise and support the front end on jackstands.
  1. Remove the wheel.
  2. Remove the hub nut and washer. Insert a long drift or dowel through the vanes in the brake rotor to hold the rotor while loosening the nut.
  3. Using a puller, force the outer end of the axle shaft out of the hub. Remove the hub/rotor.
To install:
  1. Position the shaft in the hub and install the washer and hub nut. Leave the drift in the rotor vanes and tighten the hub nut to 173 ft. lbs. (235 Nm).
  2. Remove the drift.
  3. Install the wheel and lower the vehicle.

Jan 19, 2011 | Chevrolet K3500 Cars & Trucks

1 Answer

How do you tear down front hub on 4 wleel drive truck?


FRONT DRIVE AXLE Manual Locking Hubs DISASSEMBLY AND ASSEMBLY Fig. 1: Three screws retain the cap to the hub body 91197g48.gif
Fig. 2: Remove the lockring seated in the groove of the brake rotor assembly 91197g49.gif
Fig. 3: Remove the hub body assembly from the brake rotor assembly 91197g50.gif
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the three screws retaining the cap and remove the cap from the hub.
  4. Remove the lockring seated in the groove of the brake rotor assembly.
  5. Remove the hub body assembly from the brake rotor assembly. To install:
  6. The installation is the reverse of the removal.
prev.gif next.gif

Oct 12, 2010 | 1997 Ford F250 SuperCab

1 Answer

Replace rear brake pads 2006 Chevy Impala


Hello, to replace the rear brake pads follow the following steps:

1. Lift the Chevy Impala with the jack and place it on jack stands.
2. Remove the wheels with a lug-nut wrench and set them aside. The lug-nut wrench can be found in the trunk of your Chevy Impala.
3. Remove the caliper with a ratchet and use a bungee cord to hang the caliper. Do not let the caliper hang from the brake hose, as the hose might break and cause fluid to leak.

4. Remove the brake caliper bracket from the steering knuckle with a ratchet. Set it aside.

5. Remove the break rotor from the hub. The rotor might require force to be removed; if it does, use a hammer to hit the rotor in the center, where the lug studs are located. Take care not to hit the studs.

6. Remove the new rotor from its packaging and use brake cleaner to remove the grease from the rotor. Grease is applied on the rotor in the factory to inhibit rust during storage.

7. Install the new rotor onto the hub.

8. Install the caliper bracket with new brake pads onto the rotor and fasten it to the steering knuckle. Use a ratchet to tighten the bolts.
9. Open the master cylinder reservoir so you don't break a seal while compressing the brake caliper.

10. Compress the brake caliper with a C-clamp, so that the caliper can fit over the new brake pads. Install the caliper by securing it to the brake caliper bracket with a ratchet.

Thanks


























Jul 19, 2010 | 2006 Chevrolet Impala

1 Answer

What does a ABS sensor look like on a 97 chevy blazer


mid size blazer- take off wheel-brake caliper-brake caliper bracket- rotor-and behind the hub u will see a wire going into the back of hub and is secured by a hex/torx head bolt that is ur abs sensor it looks like a small cylinder with wires attached---on the s-10 blazer some of the abs sensors set ups-- are part of the hub assembly/wheel bearing would have to change the whole unit

Mar 05, 2010 | 1997 Chevrolet Blazer

2 Answers

How do you remove front brake rotor on k 3500 4x4 1993


pull tire, remove outer hub (automatic or locking?) usually eight hex screws, behind hub assembly is a "wheel bearing nut" about 2" in diameter, this is just a circle with threads on the inside of it and four notches around the outside of it, the only way to get this out is to get the right "wheel bearing nut socket" from an automotive store, just FYI, it is probably going to be a special order tool. after "wheel bearing nut" is off the rotor will come off along with the wheel bearings, while you are in there these should probably be replaced also

Aug 14, 2009 | 1989 GMC K3500

2 Answers

Pulsating and vibrating brakes on 2003 chevy express, new pads and rotors


Rust build up is commonly found on the hubs sandwiched by the rotors/hubs

May 15, 2009 | 2003 Chevrolet Express

Not finding what you are looking for?
1998 Chevrolet K3500 Logo

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...