Question about 2006 Jeep Commander

1 Answer

Break kight burned out

How do I remove the tail light to replace the bulb for a 2006 jeep Comander

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

Open the liftgat and you should see the screws on the side of the lamp. Unscrew then and pull the lamp away from the vehicle. There should be sockets in the tailamp that screw in and out about the size on a half dollar. Pull this out and pull the bulb out straight and replace by pushing in a new bulb. Follow these directions backwards to replace the lamp. Hope this helps.

Posted on Jan 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to change tail light

Open the trunk and you will see screw underneath the carpet.remove the screw and push the light out.remove the burn bulb and replace with same model # . If the bulb is dual (5W-15W) will have different high on the locking pins. place the light back and tight slightly.DO NOT OVER TIGHT, WILL BRAKE THE KIGHT

Apr 15, 2014 | 2012 Mazda 3 i Touring 4dr Hatchback 2.0L...

1 Answer

I have a 2006 jeep liberty my driverside tail light want work all the other lights work i changed the bulb and the socket nothing

I had this issue 3 times and replaced bulbs and lenses before I found the answer! If original, there is a flaw (no recall) in the upper red lenses.
There is a half circle inner lense that is loose inside (can be seen inside the top bulb socket hole). It falls on the bulb, causing it to over heat, and blow fuses in your tail lights. Check to see if there is a burn hole inside ththe lense socket, and you should smell the scent of burnt plastic. Dealer will replace lenses for $425! I bought after market lenses which came with bulbs and wiring (plug and play) for under $100 on Ebay. Haven't had any trouble since! Chrysler says it fixed the problem, but I wouldn't pay the dealer hundreds of dollars to find out I got old stock.

Jan 29, 2013 | 2006 Jeep Liberty

1 Answer

My tail or breaks lights dont work

The 1999-2004 Grand Cherokees had some lighting issues with the tail lights. First check to see if you have power back there with a test light, if you do try changing the bulbs. If that doesn't work, Inspect the bulb sockets to see if they are burned. The issue that I saw the most was the tail light housing being warpped and breaking contact with the bulb socket. The only fix to that is to replace the tail light assemblies. Hope this helps.

Best of luck

Jun 10, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Drivers side front and rear marker (tail light) are not working but the turn signals are and they are the same bulb marker lights

check bulbs then fuses
bulbs are dual filiment means there iss 2 different wires inside the bulb and 1 will usually break but the other wont

Jan 28, 2010 | 2006 Jeep Liberty

1 Answer

When the lights are on, all rear bulb are fine. When you press on the breaks, the break lights are fine. When you press on the breaks when the lights are on the right rear goes completely dark.

Hi remove the tail light and remove the electrical connector then remove the top globe by twisting it anti clock wise then bend the contacts on the tail light up slightly and install the globe and tail light back

Nov 01, 2009 | 1999 Jeep Grand Cherokee

3 Answers

2003 jeep grand cherokee brake lights replacement

Remove screws for lens. You may have to access them from inside the hatch. Then pull out lens, then turn and pull out bulb and socket, Push and turn then pull bulb out.

Sep 12, 2009 | 2003 Jeep Grand Cherokee

2 Answers

Rear tail / brake lights not working

the problem is not the bulb it is the connectors the bulb is connected to...rebend them so they touch....its happening on all the 2000 me for any more questions...jave21@YAHOO.COM

Jan 18, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Break light problems

Have you checked to see if there is power there with a test light(with lights on).
Discoloration really means nothing.

Nov 05, 2008 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
2006 Jeep Commander Logo

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides