Question about 1983 Ford Bronco

Open Question

1983 ford bronco idling problems

Wont idle properly-stalls out

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1990 Ford Bronco Stalling

i have a 1990 for bronco xlt too and its the ignition module its getting hot.

Posted on Jan 08, 2009

Ad
chrischronic
  • 235 Answers

SOURCE: Ford Escape very low idling when cold

sounds like the idle air control motor.typical symtoms for this motor is rough idle when cold.

Posted on Jan 13, 2009

  • 87 Answers

SOURCE: idle sensor?

It could be a faulty idle speed control valve

Posted on Apr 06, 2009

emissionwiz
  • 76673 Answers

SOURCE: Will not run at an idle

Try this, it is the common reason for this problem.
Here is the common cause of surges, stalls at stops, slow idle speed, erratic idle speed, rough idle and engine hesitation (and other problems), it is in most cases the idle speed control air-bypass valve and or throttle valve and upper intake, these area's get full of gunk and combustion residue over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake

Posted on May 22, 2009

keithheavili
  • 410 Answers

SOURCE: 1994 ford escort vibrates horribly in idle.

Your Idle air control valve is probably going bad. It is located on the throttle body and is a relatively easy fix as it is only held in with 2 screws. Good luck and thanks for using FixYa!

Posted on Jun 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1983 ford bronco will start and run alright


check for a crank shaft or camshaft failure. Also try by using a scanner if you can get any fault or if you use the scanner into live measurements to see the outcome readings into all the electrical and computerized controlled units of the car.

Sep 12, 2012 | 1983 Ford Bronco

1 Answer

Stalling with wheels Cut...


you could have a couple of problems.one could be the power steering pressure switch is not working properly when turning in the direction and the other could be the iac motor(idle air control motor) is not getting the proper signal to increase the rpm when turning.have the ecm data checked on a scan tool to see what it may show.

Apr 02, 2012 | 1992 Ford Bronco

1 Answer

Every time my car comes to a red light it powers off.why?


EGR (exhaust gas recirculation),or TPS (throttle position sensor) When the vehicle makes a stop and go into idle. The RPM is basically too low to maintain the RPM, If the vehicle runs 800 RPM in park or neutral and doesnt stall the setting is correct. If it stall in neutral or park and has a hard time accelerating you will need a TPS, The EGR can stall a engine if it stays open underload approching a stop where it doesnt close properly

Mar 15, 2012 | 1983 Ford Bronco

3 Answers

My 1983 ford ltd is stalling when I come to a stop. If I am not constantly giving it gas it wants to shut off. Help!


It could be dirt in the idle jet or a problem with the idle solenoid. what should solve the problem and generally improve the performance and economy of the vehicle is a tune up and possibly a service. This will iron out all those niggly problems.

Feb 05, 2011 | 1983 Ford LTD

1 Answer

KOST 32 EGR pressure feeback fault. 4.9 EFI. Stalls when idling, runs rich


Check and see if the egr is stuck open at idle. It should have ported vacuum on egr valve. If egr is not stuck open, Check throttle position sensor, and map sensor for proper operation. Also check throttle plate for carbon buildup

Mar 13, 2010 | 1987 Ford Bronco

2 Answers

My daughter ford bronco 2 keeps stalling.


Automatic or Manual transmission?

Jun 12, 2009 | 1986 Ford Bronco

1 Answer

Will not run at an idle


Try this, it is the common reason for this problem.
Here is the common cause of surges, stalls at stops, slow idle speed, erratic idle speed, rough idle and engine hesitation (and other problems), it is in most cases the idle speed control air-bypass valve and or throttle valve and upper intake, these area's get full of gunk and combustion residue over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake

May 22, 2009 | 1987 Ford Bronco

2 Answers

1990 Ford Bronco Stalling


try cleaning your throttle plate and iac valve

Nov 20, 2008 | 1987 Ford Bronco

1 Answer

89 bronco stalling


Sounds like you have a vacuum leak somewhere??

Oct 26, 2008 | 1989 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...