Question about 2001 Honda Civic

2 Answers

Clutch bleeding i have a 2001 Honda civic just replaced the engine and i am trying to bleed the clutch but i am not getting any preasure?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 2,039 Answers

Fill the clutch cylinder with brake fluid open bleeder on slave cylinder let oil leak check the fluid in the master you should see bubble coming out after there only oil coming out close the bleeder ask somebody to go in the car pump the clutch pedal 3 time hold it there to the floor open bleeder oil come out close bleeder repeat a few time don t forget to check mthe oil level add if needed thanks pierre p.s you may need to lift the clutch pedal with our hand when you bleed the clutch that normal

Posted on Jan 12, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 740 Answers

Try opening bleeder screw on slave cylinder and let it GRAVITY BLEED, just open clutch mater and fill with fluid and then open slave cylinder bleeder screw and let it gravity bleed( run out by itself) When it does close bleeder screw and you should get pressure.(make sure master doesn't run out of fluid during this preocess).If pedal not good enough bleed as usual. PUMP PEDAL ABOUT 6 time then hold down to the floor using wrench open slave bleed screw and close back up with pedal still being held DOWN. Repeat until fluid comes out with out air.However if all this doesn't work, YOU WILL NEED TO REPLACE CLUTCH MATER CYLINDER. Conatct if you need more help and Good Luck. Thanks for using FIX YA

Posted on Jan 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 Honda civic will not move Its a five speed and the shifter goes into any gear without pressing the clutch in When I do put it into gear and try to move it just rolls like its in neutral Clutch?


Not necessarily. Check that the clutch slave cylinder is not being held in the disengaged position by a blocked clutch master cylinder. Check this by opening the bleed nipple and if the clutch arm moves to engage the clutch then replace the clutch master cylinder as the compensating port is blocked.

Jan 06, 2014 | Cars & Trucks

1 Answer

Have a 2001 honda accord just replaced master clutch cylinder and slave cylinder and clutch won't disengage. what could be the problem.


Did you bleed the clutch hydraulic system after you replaced the parts? It requires bleeding just like the brake system does.

Jul 05, 2011 | 2001 Dodge Ram 2500 Truck

1 Answer

Clutch pedal has no pressure and goes straight to the floor when pressed. clutch disk is in good condition. parked the car the night before was working perfect. next morning no pressure and out of fluid....


Pump the clutch pedal and then check for leaks again, including under the dash where the rod from the pedal goes into the clutch master cylinder. Once you find the leak, replace what's leaking and bleed the system to restore the pressure (bleeds from the slave unit, just like bleeding brakes)

May 30, 2011 | 1996 Honda Civic

1 Answer

Have fluid in res. lines are free bleeder has fluid but can't get preasure on clutch arm


Clutches can be a pain, do you have fluid bleed out with no air bubbles coming out, if you cant get it to bleed it works best to raise the front of the car up with a jack or as high as you can get it within reason, doing this makes the slave cylinder the highest point therefore air will travel to the highest point making it easier to bleed and get all the air out. if you still cant get it to bleed after that try letting it gravity bleed for a few minutes and then try bleeding and if that dont work possible bad master cylinder. If this is a problem that developed and you have not replaced clutch slave cylinder the slave cylinder is probably the issue

Apr 07, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

99 civic clutch hangs


you may still have an air pocket in the line try bleeding it a little more

Mar 04, 2010 | 2000 Honda Civic

1 Answer

Honda civic lx - clutch falls part 2


the same principle applies to bleeding the clutch like you do the brakes . have someone help you with this. have them push in the clutch and hold, then open the bleed screw on the cylinder till you get a steady stream with no air bubbles. repeat this several times. this should solve the problem

Apr 27, 2009 | 1990 Honda Civic

1 Answer

I have a 2001 Honda civic i just replaced the engine and am trying to bleed the clutch but i am getting no presure what do i do?


you should first gravity bleed it.fill the reservoir and open the slave bleeder screw .let it drop in a container till you see no more air bubbles.then add fluid and pump the pedal several times till you feel a bit ressistance.open bleeder again and repit till no air comes out .tou may have to do it several times. good luck

Jan 12, 2009 | 2001 Honda Accord

2 Answers

Bleeding clutch slave cylinder


i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Nov 15, 2008 | 1996 Honda Accord

1 Answer

Bleeding clutch slave cylinder


if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Aug 05, 2008 | 2001 Honda Accord

Not finding what you are looking for?
2001 Honda Civic Logo

634 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...