Question about 2009 Dodge Journey

Open Question

How to change brake pads on 2010 dodge journey

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
polarcycle
  • 1392 Answers

SOURCE: Change front brake pads on 2001 dodge durango

Front, remove the hold down clip, should be a 7mm or a 45 torx bit to get the slider pins out. If you are not sure what you are doing, please spend a little money and have a pro do it for your safety, and the safety of others around you.

Posted on Mar 18, 2009

Ad
localwonder
  • 6784 Answers

SOURCE: worn brake pads

Front brake pad exchange guide.

Step1 Park the Dodge Durango on a flat surface. Put the emergency brake on and put wedges behind the wheels to prevent the vehicle from rolling. Disconnect the negative battery cable from the battery. Drain 2/3 of the brake fluid from the master cylinder, using a syringe. Remove the wheel and the tire assemblies. Step2 Compress the caliper piston back into the caliper bore using a large C-clamp to drive the piston into the bore. Use additional force if it is required. Using a 3/8 inch hex wrench or socket remove the caliper mounting bolts. Step3 Rotate the caliper rearward off the rotor and out from its mount. Remove the inboard and outboard brake pads. Remove the spring clip that holds the inboard brakes in the caliper. Tilt the pad out at the top to unseat the clip. Remove the retaining spring that secures it in the caliper. Unseat one spring end and rotate the pad out of the caliper. Step4 Suspend the caliper assembly from the Durango frame using mechanic's wire. Do not allow the caliper assembly to dangle from the brake hose as this may damage the brake hose. Step5 Clean the surfaces of the caliper and steering knuckle with a wire brush. Apply multi-mileage grease or similar product. Using brake fluid or break cleaner clean the caliper slide pins. Apply a light coating of silicone grease to the pins. Step6 Install the inboard brake pad and it's spring. Install the outboard brake pad. Install the caliper over the rotor and seat it in its original position until it is flush. Using a torque wrench, torque the slide caliper pins to 22 ft./lbs. Step7 Add brake fluid to the master cylinder. Bleed the brakes. Reconnect the negative battery cable to the battery. Start the engine and pump the brakes 3-4 times to seat the brake pads. Reinstall the wheels. Test drive the Durango at slow to moderate speeds to ensure that the maintenance was performed correctly.
Rear brake pad exchange.

Step1 Lift the Durango off the ground with a car jack. Support the vehicle on all sides with jack stands. Keep children and small animals out of the vicinity when you replace the brakes. Step2 Loosen the lug nuts on the wheels with a torque wrench. Remove the wheel and tire assemblies and set them aside, face up, to prevent damage. Step3 Compress the caliper and remove it by lifting the top up and off the caliper adapter. Hang the caliper from the Durango's frame with mechanical wire. Step4 Remove the inboard and outboard brake shoes from the caliper adapter. Take off the top and bottom anti-rattle springs. Keep the springs separated, as they aren't interchangeable. Step5 Press the piston into the bore with a C-clamp. To prevent damage to the pistons, insert an old brake shoe in between the C-clamp and caliper piston. Remove the C-clamp. Step6 Wipe down the caliper mounting adapter and anti-rattle springs with brake cleaner. Grease the anti-rattle springs with brake grease. Install the bottom anti-rattle springs, followed by the top anti-rattle springs. Step7 Install the inboard brake shoes followed by the outboard brake shoes. Replace the caliper and the wheel and tire assemblies. Lower the vehicle to the ground and pump the brakes to seat the pistons.


Please rate and god bless:)


Posted on Apr 02, 2009

tse22
  • 103 Answers

SOURCE: Changing Rear brake pads 2005 dodge grand caravan

There are 2 bolts on the "inside" on the caliper towards the bottom they use an allen wrench socket.

Posted on May 13, 2009

  • 2 Answers

SOURCE: 2005 Dodge Grand Caravan brakes

i dont know if this makes sense, if its the big clip, you push in the cylinder and twist until the clipp comes off

Posted on Jun 13, 2009

egstriker23
  • 44 Answers

SOURCE: How to get at the

First, you will need to jack up the driver side front wheel.
Then, remove the wheel.
With the wheel off, you can remove the plastic fasteners holding the battery access panel (bottom front section of inner wheel well).
After you remove the cover you can reach in and disconnect the cables, then remove the battery.

Hope this helps!

Posted on Oct 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why is my parking brake clicking when i press the brakes?


Some parking brakes have a ratchet adjustment to take up slack. Or it maybe the exhaust heating up and you haven't noticed it before.

Jul 27, 2017 | 2010 Dodge Journey

1 Answer

How do you replace the front brake pads on a 2010 Dodge journey?


remove the wheel after supporting the car,with a jack stand, then you remove the two bolts that holds the brake caliper then remove the old pads then you push back the caliper piston with a clamp or a big channel lock pliers replace the new pads and after you did the two front wheels start your car and before moving pump up the brakes properly

May 03, 2014 | 2009 Dodge Journey

1 Answer

How to replace front disc brake pads on a 2009 Dodge Journey?


remove the front wheel and support the van then remove the two bolts that hold the caliper then remove the old pads then using a clamp or big channel lock plies press the caliper piston in so the caliper can go on after you put on the new pads after you would of replace your wheels pump up your breaks and check to see if you need to put in some more brake fluid

May 03, 2014 | 2009 Dodge Journey

1 Answer

I have a 2010 dodge journey and the shifter get stuck in park


If your parking on an incline, that would possibly cause it plus switch at brake pedal may need to be adjusted. If you find pushing harder on brake pedal helps, have it adjusted, or replaced.

Jan 18, 2014 | 2010 Dodge Grand Caravan

2 Answers

Horn won't stop honking dodge journey


replace horn switch under air bag part no 05189428AC

Oct 20, 2013 | 2010 Dodge Journey

1 Answer

Replaced brake pads on 2009 Dodge Journey, but now when the brakes are pressed the caliper won't engage.


Well you need to check your fluid level on the master cylinder first. Then I suggest that you bleed the brake system. Always start bleeding from the wheel furthest away from the master.

Nov 22, 2010 | 2009 Dodge Journey

Not finding what you are looking for?
2009 Dodge Journey Logo

Related Topics:

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...