Question about Cars & Trucks

1 Answer

The back lights on my 99 Chevy s10 are out. I've checked fuses and bulbs and all seem to be fine. What else can I do to fix it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,185 Answers

Hi Jesse,could be your headlight switch,here's a link on how to replace.Here's a link to the switch.

Posted on Dec 04, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1998 Chevy S10 pickup backup lights don't work

Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Posted on Sep 06, 2008

  • 61 Answers

SOURCE: Dashboard light not workin on my 99 olds intrigue

It could be the dimmer switch.

Posted on Jan 28, 2009

  • 3 Answers

SOURCE: My third brake light dosen't work on my chevy s10 94'

I had a similar problem with my 1994 S-10 LS extended cab. Both tail brake lights worked fine. I removed the 3rd brake light cover and tested for voltage at the steel center of the two rivets and found the positive (driver side) negative (passenger side) were good. I checked the two metal strips that send power to bulbs and found the positive side was open. Seems the flared side of the rivet was not making contact with the metal strip. I bucked the rivet with a punch and hammer and it took care of the problem.

Posted on Jun 23, 2009

  • 1 Answer

SOURCE: Volvo S80 - Low beam out - Changed bulb & fuses

all i did i unpluged the batter for 5 min and pressed the brake pedual while the batttery was unhooked and when i plugged it back in it solved my problem it has been working all day fine

Posted on Jul 03, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Chevy S10 Blazer that seems to start in second gear


run fault codes to check for servo/ solenoid problems --TCM faults

Jan 28, 2014 | Cars & Trucks

1 Answer

My 1995 chevy s10 brake lights reverse lights high mount light all went out and cant find out why


Check connection on frame that operate rear. Do the rear parking lights work, turn signals?

Dec 26, 2013 | Chevrolet S 10 Cars & Trucks

3 Answers

99 Chevy S10 Pickup's Tail Lights Won't Turn Off


Obviously you have a short somehow power is bleading over to this circuit. You may be forced to do some hard debuging (i.e wiring diagram, test light isolate the problem on the circuit).

If I were taking a guess I would try the following:
1) Remove the fuse for the taillight
2) If the light goes out I would start looking at the dashboard light switch
3) If the light does not go out then I would start looking toward the rear end of the truck wires that are scouffed, trailer light connections ect.

Hope this gives you a start, needless to say a short can take forever to find.

Feb 17, 2010 | 1999 Chevrolet S-10 Pickup

2 Answers

Need a wiring diagram for a chevy s10. brake


your power starts at the brake light fuse,check with a test light,then proceed to stop light switch on brake pedal under dash,one wire will be hot when when you check it with your test light, the other won't be until you press down the brake pedal then the power flows through to the second wire,if no power to second wire replace switch,if you have power remove tail light bulbs and check for power in side socket.

Nov 24, 2009 | 1997 Chevrolet S-10 Pickup

3 Answers

1991 Chevy Blazer dashboard lights are burned out. Can't read


Your dash needs to come out. These bulbs push into a plastic piece that "twists" into the back of the dash board. (About a 1/4 turn) Unless you can get at them from underneath, but I think it's to tight.

Aug 13, 2009 | 1989 Chevrolet S-10 Blazer

2 Answers

2003 Chevy S10 Pickup fast flashing signal lights


Recheck your wire harness to your trailer hook up. You may have a short in the wire. Good luck 

Apr 06, 2009 | 2003 Chevrolet S-10

2 Answers

My third brake light dosen't work on my chevy s10 94'


I had a similar problem with my 1994 S-10 LS extended cab. Both tail brake lights worked fine. I removed the 3rd brake light cover and tested for voltage at the steel center of the two rivets and found the positive (driver side) negative (passenger side) were good. I checked the two metal strips that send power to bulbs and found the positive side was open. Seems the flared side of the rivet was not making contact with the metal strip. I bucked the rivet with a punch and hammer and it took care of the problem.

Mar 17, 2009 | 1994 Chevrolet S-10

4 Answers

1998 Chevy S10 pickup backup lights don't work


Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Sep 06, 2008 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...