Question about 2000 Lincoln Continental

1 Answer

Replacing lincoln continetal brakes

How do you get the brake hose to remove? One of my calipers is stuck and I think it is because the hose to the emergency brake hasn't been removed. But I don't know how to do it :(

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

Sounds like you need to change the caliper & hose together. check the e-brake cable going to caliper make sure it is not frozen you may end chaging that also very comin problem

Posted on Mar 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix1977 corvette stuck front caliper?


replace both calipers and bleed system. remove wheel, unbolt brake flex hose where it mounts to the caliper,clamping hose to keep from losing brake fluid, unbolt caliper from caliper mounting bracket. and remove caliper. re-install in reverse order bleeding front brakes making sure master cylinder doesn`t run out of brake fluid.

Sep 03, 2014 | Cars & Trucks

3 Answers

1994 LINCOLN CONTINENTAL


Hi Terry,
Please check out this Link : http://www.autopartswarehouse.com/featured/books_and_manuals/1461465620.html
Here you will find the details regarding your Car and how you can check and repair the breaks without taking it to a mechanic.
I hope this helps.....

Jun 02, 2008 | 1994 Lincoln Continental

1 Answer

Carburetor vacuum diagram


The flexible brake hoses that screw into the calipers are the most neglected part of most brake systems, along with dirty flluid. The flex hoses are probably swollen inside and holding pressure on the calipers. Remove the flex brake hoses and try to blow through them. If you cannot or it is very difficult the hoses are bad.At a minimum I recommend replacing hoses on both sides. As for stuck pistons, try collapsing the calipers. If the pistons won't retract then replace the calipers too.

Mar 14, 2014 | Cars & Trucks

1 Answer

My 1991 Lincoln town car sat for awhile. Now when driving smell a burning electrical smell and when braking it pulls to the left. Any idea what the problem is?


You have a lot of rust on all your brake components

You will need to completely strip all 4 brakes & remove
all rust and lube necessary parts

Don't misunderstand my point here

You do not necessarily need new rotors or brake pads

You may want to however, replace the flexible rubber
brake hoses, as they may have collapsed inside and
your brakes do not release,thus the brake pad smell

Also you could have rusted and frozen caliper pistons

The rust,the flex hoses & possibly the calipers, are your
problems,and the cause of the bakes not releasing

Mar 06, 2011 | 1991 Lincoln Town Car

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

2 Answers

I have a 86 lincoln mark vii and i have a problem with the right front brake the caliper doesnt want to relase after the brake pedal is released and heats up and smokes piston still moves back and forth...


replace the brake hose they get what is called a fissure inside hose and it will act like a check valve you hit brake pedal and when you let off brake pedal the fissure inside hose will hold pressure on caliper i see it all the time next time it locks up open the bleeder screw on caliper and the wheel will free up because you release the pressure that can,t go thru hose

Sep 03, 2010 | 1986 Lincoln Mark VII

1 Answer

How do I replace the ear brakes?


Bonneville, LeSabre, Park Avenue 2000-2005

Brake Caliper - Removal & Installation

CAUTION Dust and dirt accumulating on brake parts during normal use may contain asbestos fibers from production or aftermarket brake linings. Breathing excessive concentrations of asbestos fibers can cause serious bodily harm. Exercise care when servicing brake parts. Do not sand or grind brake lining unless equipment used is designed to contain the dust residue. Do not clean brake parts with compressed air or by dry brushing. Cleaning should be done by dampening the brake components with a fine mist of water, then wiping the brake components clean with a dampened cloth. Dispose of cloth and all residue containing asbestos fibers in an impermeable container with the appropriate label. Follow practices prescribed by the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA) for the handling, processing, and disposing of dust or debris that may contain asbestos fibers.
Inspect the fluid level in the brake master cylinder reservoir. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed from the reservoir before proceeding. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding.
  1. Raise the vehicle and suitably support.
  2. Remove the tire and wheel assembly.
  3. Pull down on the front park brake cable.
  4. Remove the front park brake cable from the park brake cable connector.
    NOTE When using a large C-clamp to compress a caliper piston into a caliper bore of a caliper equipped with an integral park brake mechanism, do not exceed more than 1 mm (0.039 in.) of piston travel. Exceeding this amount of piston travel will cause damage to the internal adjusting mechanism and/or the integral park brake mechanism.
  5. Install a large C-clamp over the top of the brake caliper housing and against the back of the outboard brake pad. Compress the brake caliper piston into brake caliper bore to allow the piston enough clearance to slide the brake caliper off the brake rotor.
  6. Remove the C-clamp.
    NOTE Be sure to plug the opening in the brake caliper and brake hose to prevent fluid loss and/or contamination.
  7. Remove brake hose to caliper bolt attaching the brake hose to the brake caliper.
  8. Remove the brake hose from the brake caliper.
  9. Remove and discard the two copper brake hose gaskets. These gaskets may be stuck to the brake caliper and/or the brake hose end.
  10. Remove the park brake cable bracket from the brake caliper. Leave the park brake cable attached to the cable bracket.
  11. Disconnect the park brake cable from the park brake lever on the brake caliper.
  12. Remove the lower brake caliper pin bolt.
  13. Rotate the brake caliper up.
  14. Remove the brake caliper from the upper brake caliper pin bolt.
To install:
  1. If reusing the brake caliper retainers, clean the sleeves using denatured alcohol, or equivalent.
  2. Lubricate the brake caliper pin bolts with a thin coat of high temperature silicone lube.
  3. Install the brake caliper to the upper caliper pin bolt.
  4. Rotate the brake caliper down over the brake pads into the brake caliper bracket.
  5. Install the brake caliper pin bolts. Tighten the brake caliper pin bolts to 27 Nm (20 ft. lbs.).
  6. Remove the plugs in the brake hose end.
    NOTE Install NEW copper brake hose gaskets.
  7. Assemble the brake hose bolt and the NEW copper brake hose gaskets to the brake hose.
  8. Install the brake hose to caliper bolt to the brake caliper. Tighten the brake hose to caliper bolt to 44 Nm (33 ft. lbs.).
  9. Connect the park brake cable to the park brake lever on the brake caliper.
  10. Install the park brake cable bracket to the brake caliper. Tighten the park brake cable bracket bolt to 43 Nm (32 ft. lbs.).
  11. Install the front park brake cable to the park brake cable connector.
  12. Bleed the brake system.
  13. With the engine OFF, gradually apply the brake pedal to approximately 2 / 3 of its travel distance.
  14. Slowly release the brake pedal.
  15. Wait 15 seconds, then repeat until a firm brake pedal is obtained. This will properly seat the brake caliper pistons and brake pads.
  16. Install the tire and wheel assembly.
  17. Lower the vehicle.

NOTE The Bosch 2U ABS system cannot increase brake pressure above master cylinder pressure applied by during braking. There is no need to depressurize the system prior to service.
  1. Remove brake fluid from the master cylinder reservoir until the reservoir is approximately 1 / 3 full.
  2. Remove the front wheel. Mark the position of the wheel to the wheel studs, prior to removal, for installation reference.
  3. Install 2 lug nuts to retain the rotor once the caliper is removed.
  4. Using a large C-clamp, bottom the piston in the caliper bore by positioning the C-clamp on the outboard pad and on the round portion of the brake caliper where the piston is housed.
  5. Remove the banjo bolt that fastens the brake hose to the brake caliper. Discard the gaskets.
  6. Cap the brake line to avoid excessive fluid loss or fluid contamination.
  7. Remove the rubber dust boots from the caliper mounting bolt heads (if equipped).
  8. Remove the caliper mounting bolts.
  9. Remove the park brake cable from the caliper.
  10. Remove the caliper from the vehicle.
  11. Remove the brake pads.
To install:
  1. Install the brake pads. Lubricate the slides where the caliper mounts on the steering knuckle with silicone grease.
  2. Install the caliper over the rotor.
  3. Install the caliper mounting bolts. Torque the mounting bolts to 38 ft. lbs. (51 Nm).
  4. Install the park brake cable.
  5. Install the rubber dust boots over the caliper mounting bolt heads (if equipped).

    542f486.jpg
    Fig. Measuring the caliper clearance
  6. Check the clearance between the brake caliper and caliper bracket stops. If the clearance is too tight, check the caliper leading and trailing edges for build up. File down as necessary.
  7. Connect the brake hose to the caliper. Install the brake hose banjo bolt, using new gaskets, and torque to 33 ft. lbs. (45 Nm).
  8. Remove the lug nuts used to secure the rotor.
  9. Install the wheel, aligning the reference marks made during removal, and torque the lug nuts to 100 ft. lbs. (140 Nm).
  10. Refill the master cylinder and bleed the brake system using the recommended procedure.
  11. Road test the vehicle and check for proper braking performance

Hope helps (remember rated this).

Jul 08, 2010 | 2003 Pontiac Bonneville

3 Answers

Put new brake pads on, now brakes were smoking. Sticking caliper?


They are rather easy to replace, disconnect the brake hose, and remove the caliper as you did replacing the pads. You'll need to then bleed the caliper until clear fluid, with no air bubbles come from the bleeder screw. Check that you don't have a collapsed brake hose, not letting the fluid return to the master cylinder.

May 24, 2010 | 1992 GMC Jimmy

1 Answer

1992 GMC Sierra pickup front brakes pad not releasing after letting off of brake.


There can only be a few reasons for this. 1, the piston is stuck in the caliper. 2, the brake hose has collapsed in the middle and won't allow fluid to flow back towards the master cylinder. Pull the caliper off and see if it can be pressed back with a C-clamp easily. If not, remove the brake hose then see if you can press it back. If you can not, the caliper piston is stuck. If you can, the hose is collapsed. Replace the appropriate part then bleed the brakes. You should no longer have the problem.

Feb 09, 2009 | 1991 GMC S-15 Jimmy

1 Answer

Rear brakes


The caliper is probably stuck, I had to replace one of mine, drivers rear. The piston on the caliper screws back in, so you'll need a caliper press to seat the piston.

Oct 25, 2008 | 2000 Lincoln LS

Not finding what you are looking for?
2000 Lincoln Continental Logo

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...