Question about Cars & Trucks

Open Question

Chevrolet impala 2002 power seats not working

Power seats seems frozen in place will not move back or forth or up and down..how can this be fixedm without deploying the airbags?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76691 Answers

SOURCE: power front seat won't go back and forth

U will have to replace the entire power seat transmission, there is no other way to get the part, I know it sucks but that is the way it is, try finding a used unit, or swap the passenger side to the drivers side.

Posted on Dec 29, 2008

Ad
  • 88 Answers

SOURCE: Power seats won't move

YOU WILL BE LOOKING AT ANOTHER POWER SEAT MOTOR.

Posted on Dec 26, 2008

pingman37
  • 58 Answers

SOURCE: power seat switch

It is most definitely the seat slide motor. Most infiniti drivers seats have three different motors. I30, I35's and QX4's all had problems with the seat slide motors. You can tap on the slide motor which is under the front of the seat and it will probably work for a little while, but it WILL stop working completely. There was actually a Technical Service Bulletin regarding this issue because there were so many vehicles that had this problem. I hate to see that guy waste money trying to get a circuit board rebuilt that absolutely will not solve the problem. 

Posted on May 06, 2009

  • 323 Answers

SOURCE: driver's airbag light on 2007 PT Cruiser convertable

The first code is for "driver seat track position sensor low". The module detects that the sensor input is less than or equal to 0.3 mA. The second code is referring to the first code. I have no idea what the third code is. Basically you have two different communication systems mixed. The 2001 uses the PCI bus system and the 2007 uses the CAN bus which is much faster. The first code is a CAN bus code and the second is a PCI code. As far as the airbag deploying in the event of a collision, I don't believe it will with an active code in the system. I hope this helps.

Posted on May 13, 2009

jj127
  • 37 Answers

SOURCE: 2000 Chevrolet Malibu LS airbag problems

The passenger side airbag is a lot easier then driver side. Take the glove box out and you will see two 10mm bolts holding it in place. When you open the passenger side front door, remove the panel on the side of the dash and you will see yellow connectors.The 1 closest to the front is attached to the air bag, it is clipped into the frame. Just pull it loose and take it out and your done. For the Driver side, it takes a skinny T27 to remove the two star bolts, then just disconnect the horn red clip and ground and install new airbag. The module is located under the passenger seat, underneath the carpet. Kinda stupid but thats where its at. You also need to replace the front impact sensor located behind the grille on the back side of the metal bar to each side. Follow the hood latch down. Also just to make sure, you know to disconnect the battery before you do all this. You don't want new airbags to accidentally deploy.

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Front drivers seat will not slide back and forth.


No, check for a blockage in the seat track. You have one power source for all seat functions. If it works one way but not the others it is either a bad switch, or bad motor, or a blockage.

Sep 02, 2014 | 2000 Nissan Maxima

1 Answer

Power seat won't slide back, black plug is hanging out


That is the seat heater plug most likely and you car is not equipped with that accessory. All cars come with the same wiring. Does the power seat switch have 12 volts present?

Mar 14, 2014 | 2002 Audi A6

1 Answer

2009 impala driver side power seat won't move up/down, makes whirring sound when attempted. Moves forward backward. Passenger seat works properly.


Before you do any of the expensive things disconnect and reconnect the wiring to the seat I had the same exact problem with my 2009 Chevy Impala and was ready to take it to the dealer when I disconnected the power cables to it and reconnected them I found that one of the Harnesses was loose and the problem was solved

Sep 12, 2012 | 2009 Chevrolet Impala

1 Answer

How to replace electric fuel pump in 2002 impala ls


Hello!
You put down the back seat and lift open the trunk lid for fresh air. Raise the carpet off the inside of the trunk close to the back seat. You should see a trap door. Lift it and there is your fuel tank and pump!!!

Jan 10, 2012 | 2002 Chevrolet Impala

1 Answer

My power driver seat will not move foward but it will go backward


The seat has a transmission to move the seat up, down, foward , & back. Screw jacks adjust the seat up & down. Cables move the seat forward & back. The cable it seems had to break or the end of the cable has rounded out. Possibly the cable rounded out the seat it rides in the transimission housing too. You will need to remove the seat to find out

Oct 02, 2011 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Power seat control not working to move seat back. works to move seat forward and the other power controls work for seat back postion and such. how can i manually move the seat back. once it is back it can...


that is easy find the motor under the seat that moves the seat back and forth take and neg wire and a hot wire carefully touch the twoo prongs going to the motor after diconnecting the plug going into the motor. it sould go forward one way and croos the wires to get it to go the other way if this works get a new switch and have a working seat.

Jul 01, 2010 | 2002 Chevrolet TrailBlazer

2 Answers

How do i take out a 2002 impala front seat in order to replace the power seat motor?


the front seat in the impala does not have front bolts...there are 2 bolts in the back..remove then pull back on the seat and lift out !

Jun 04, 2010 | 2002 Chevrolet Impala

1 Answer

Electric seats in 1999 Siverado move back & forth


the tracks for the seats are pressed out aluminum. they have motors that control the seat adjuster. it seems when worn they will not stay in place and need to be replaced. If anyone that is very overweigh this will create this problem sooner than expected
The seats are made to withstand 250 max. I have sold tracks by GM for 30 years and know personally what they can do in time from weight
(nothing personal)

Feb 20, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

My passenger seat won't lock into position. It slides back and forth as I drive and the bar that you pull on to move it back and forth is stuck in the up position.


There is a spring that pull's the handle back to lock position that might be broke or the locking mechanism might be gummed up.the spring can't be bought seperatly so check a hardware store or replace the seat track assembly.

Aug 11, 2009 | 2000 Chevrolet S-10

1 Answer

Power seats won't move


YOU WILL BE LOOKING AT ANOTHER POWER SEAT MOTOR.

Dec 25, 2008 | 2002 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...