Question about BMW X5 Series

1 Answer

Honda CRV Keyless Entry stopped working. Pushing any button on either remote does nothing. They both just stopped working at the same time out of the blue. All doors function properly from inside

Pushing any button on either remote does nothing. They both just stopped working at the same time out of the blue. All doors function properly from inside controls. I checked the fuses, and all were ok.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 54 Answers

Check the batteries in the remotes. It might just be a massive coincidence and the 2 stopped working at the same time. Failing that I would guess the reciever is the problem

Posted on Dec 04, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 36 Answers

SOURCE: Toyota 4runner gate window, wiper, and keyless entry not working

make sure the back window is all the way up then try the wiper, if it still does not work then it is a sensor for the rear window (about $30.00) if you installed it yourself

Posted on Jul 21, 2009

  • 5 Answers

SOURCE: keyless entry won't work

I have a 1999 BMW E46 I have had a problem with the keyless entry myself. I brought the car to BMW Dealer and they told me that my Lock had an issue and that they need to repair some wiring wich would cost me $1,023.98 to find out that it was a fuse that burned out. I have replaced the 5 amp fuse with another one but it burned the fuse again so I put a 10 amp fuse and i have not had a problems since. In my car is fuse # 54 if Im not mistaken. But waht you can do is open the fuse box which is located in your glove compartment look for a diagram that shows you which fuse is where it will give you a fuse name a number where the fuse is located and how many amps fuse it is.

Posted on Dec 23, 2008

  • 65 Answers

SOURCE: Keyless Entry and Remote

I have had this problem take you drivers door put your key and un-lock from the out side with key (NO) then open the door push un-lock from the inside button and then set from you remote and it should set if not push un-lock then lock and then do the un-lock with the key. Let me know if that works. what my car did was locked from the inside and I had the problem were it would not work till I un-locked from the out side plus I had to go to radio shack and change the battery from the control.
Hope good happens.
Nikki2913

Posted on Dec 29, 2008

  • 28 Answers

SOURCE: keyless entry doesn't work, batteries good in transmitter,fuses good

there is a tester that checks for Rf signals from your remote. if the batteries are good, you should get a strong signal from it. most likely the remote went bad

Posted on May 12, 2009

  • 77 Answers

SOURCE: keyless entry on honda civic 2006 not working

The keyless entry is designed to work with the doors closed (closed - not locked). If the door ajar sensor thinks the door is open the keyless entry is disabled. When you manually lock the door it might tighten the door just enough to activate the keyless entry. I would try slamming all the doors closed and then see if the keyless entry works. If it still wont work have the wiring checked on the front door lock.

Posted on May 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

KEYLESS REMOTE LOCKS DOORS WITHOUT PUSHING REMOTE


This one is tricky I could be the way the keyless entry was programmed into the settings on the car this one is tricky they could be the way the keyless entry was programmed into the settings on the car

Dec 19, 2015 | Cars & Trucks

2 Answers

Keyless entry civic aerodeck 1.6ise year 2000


Do you have multiple keyless entries for this car? If so does the other one still work, perhaps it just needs to be reprogrammed. Take it to your nearest Honda dealer and they should be able to get it working again. If it is constantly locking and unlocking, the computer could be getting a signal from the remote which would indicate a reprogramming is needed too.

Please let me know how this goes.

May 21, 2008 | 2000 Honda Civic

1 Answer

I have a 2000 ford mustang. Suddenly my keyless entry remote stopped working. I replaced the battery and turned the off and on 8 times and the locks cycled. after which i pushed the unlock but nothing...


The keyless entry system is controlled by the (GEM) - generic electronic module .
Keyless Entry The electronic door lock system has two main components:
  • generic electronic module (GEM)(14B204)
  • keyless entry remote transmitter (15K601)
  • NOTE: Battery power and ground must be remove before disconnecting the GEM connectors to avoid setting false codes.
    Power Locks Operation The power locks feature allows the customer to lock and unlock the doors via momentary switches located on the driver and passenger door. When the GEM detects a momentary press of the driver or passenger lock button, the GEM will supply power to the driver or passenger lock actuators for approximately 250 ms from relays internal to the GEM. When the GEM detects a momentary press of the driver or passenger unlock button, the GEM will supply power to the driver or passenger unlock actuators for approximately 250 ms from relays internal to the GEM.
    Remote Keyless Entry Door Locks Operation The remote entry feature allows the customer to unlock the driver door, unlock all doors, and lock all doors using a valid remote transmitter as long as the ignition switch is not in RUN or START. The driver door is unlocked whenever the GEM detects a valid remote transmitter unlock transmission. All the doors are unlocked when the GEM detects a second valid remote transmitter unlock transmission within three seconds of the first transmission. All the doors are locked when the GEM detects a valid remote transmitter lock transmission. If the GEM detects a second valid remote transmitter lock transmission within three seconds of the first transmission, the doors will lock again, the horn will sound for 20 ms and the parking lamps will flash for 200 ms to indicate the doors are locked. If the GEM detects the driver or passenger door is ajar during the second lock transmission, the doors are locked again and the horn is sounded twice. If the GEM detects a valid remote transmitter lock transmission within three seconds of detecting a valid remote transmitter unlock transmission, the GEM will lock all the doors
    • The doors do not lock/unlock using the remote transmitter
    • Ignition switch.
    • GEM.
    • Remote transmitter.
    • Remote transmitter batteries.
    • GO to Pinpoint Test C .
    You followed the program instructions to the letter ? Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
    NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
    NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
    1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
    1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met.
      Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
    1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
    1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
    1. Take an have the vehicle checked for DTC'S
B1396 Power Door Lock Circuit Short to Battery GEM GO to Pinpoint Test B . B1397 Power Door Unlock Circuit Short to Battery GEM

Apr 12, 2017 | Ford Mustang Cars & Trucks

1 Answer

Hi. I lost the key to my 2009 accord xl. I picked up a replacement today and was given "instructions" as to how to make the necessary steps to get the car started - just to get the car up to the...


  • Have a seat in your Honda and close the doors, but make sure they are unlocked.

  • 2

    Turn your ignition key to the "On" position, labeled by two lines (II). Press the "Unlock" button on your keyless remote. Turn your ignition key to the "Off" position.

  • 3

    Repeat the procedure three times, and then turn the ignition key to "On." Immediately press the "Lock" button on your keyless entry. Listen for the doors to lock, and then unlock to signal that you are in programming mode.

  • 4

    Press the "Lock" button on the keyless remote, and then turn the ignition to the "Off" position to confirm.



  • Read more: How to Program a Honda Keyless Entry ' eHow.com http://www.ehow.com/how_5523557_program-honda-keyless-entry.html#ixzz1A7h1nyC1

    Jan 05, 2011 | Honda Accord Cars & Trucks

    1 Answer

    Keyless remotes not working


    Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
    Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
    NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
    1. Make sure that the anti-theft system is not armed or triggered.
    1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
    1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
    1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
    1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

    Jun 06, 2010 | 1998 Ford F150 Regular Cab

    1 Answer

    Keyless Remote Entry Doesn't Work


    Hi, Had similar problem and replaced the key fob battery, which was a waste of money because the faulty item was my "door lock actuator".  Had it replaced at a Maryland repair shop for around $180, Honda dealer wanted over $250. Good luck :)

    May 29, 2009 | 2003 Honda Accord

    2 Answers

    My remote for the keyless entry does not work.


    does trunk button work? panic button?
    here's 2003 info:


    • The doors do not lock/unlock using the remote transmitter
    • Remote transmitter.
    • Driver door module (DDM).
    • Go To Pinpoint Test G .

    SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
    GENERAL PROCEDURES Remote Transmitter Programming
    1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
    1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
      Press any button on the transmitter to be programmed.
    1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
    1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
    --------------------------------------------------------------
    report back

    Mar 22, 2009 | 2004 Lincoln LS

    1 Answer

    Reset keyless entry on 1998 honda civic


    Okay, here goes-

    1. Turn Key to on position.
    2. Push and hold **valet button on the stock radio.
    **Valet button is skinny bar located between am/fm & cd/tape buttons on stock radio.
    Door locks will cycle one time.

    3. Press any button on remote one time within 20 seconds. Door locks will cycle again.
    4. To program up to 4 additional remotes repeat step 3 for each additonal remote.
    5. Turn key off programming is complete.

    Thanks for using Fixya, please rate if this helps :)

    Mar 16, 2009 | 1998 Honda Civic

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    1,123 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top BMW Experts

    Frankie B

    Level 2 Expert

    65 Answers

    Fred Sops

    Level 2 Expert

    272 Answers

    Doberman

    Level 2 Expert

    254 Answers

    Are you a BMW Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...