Question about 1990 Mercedes-Benz 190

1 Answer

I have 1990 190e 2.6 lost fire to plugs replaced ign coil nothing problem is intermittent

The custmer said the car starts sometimes once it does it starts the rest of the day.he replaced the ign coil to solve the problem no luck

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have the same symptoms with my car. My cap and rotor, ignition wires and spark plugs are brand new - so it's not a spark problem(at least in my case - you should check the spark on yours). What I recommend is to do a fuel pressure test. There are multiple things that could go wrong with it- first, fuel pump or pumps(mine has two) are old and do not put out enough pressure in the system. Second, there could be a small leak somewhere in the system - common. Because of that, and because the k-jetronic system is fairly complicated and has a lot of parts that could go bad - this might be hard to diagnose. On Youtube you can find a detailed description of the system and its components. Also a common problem seems to be the fuel distributor or the plunger. You are going to have to remove the air filter housing and visually inspect for leaks. Also look behind the right rear tire where the fuel pump/pumps, filter and accumulator is. Even the smallest leak in the system could potentially cause the engine not to start until there is enough pressure in the fuel system. If the engine is running fine after it starts, you probably have one of the problems I mentioned above.
Good luck

Posted on Jan 30, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Firing order coil pack 2000 ford explore 5-0


Firing Order is 1 3 7 2 6 5 4 8

JF: Integrated Ignition Coil On Plug Coil 1 Through 10 Failure

2000 PCED On Board Diagnostics II


SECTION 5: Pinpoint Tests




Procedure revision date: 01/31/2001










JF: Integrated Ignition Coil On Plug Coil 1 Through 10 Failure


? JF: Introduction




JF1 DETERMINE WHICH COIL IS NOT FIRING

    Note: Electronic ignition engine timing is entirely controlled by the PCM. Electronic ignition timing is NOT adjustable. Do not attempt to check base timing. You will receive false readings.

  • Determine which coil is not firing using information from Pinpoint Test JB or DTC and the table at the beginning of this pinpoint test.


  • Record cylinder, coil and PCM pin number from the table.


Have the cylinder number, coil driver and PCM pin number been recorded?







Yes


No






GO to JF2.


To obtain required information, GO to JF1 and REPEAT.




JF2 DTC P0351, P0356, P0357: CRANKSHAFT POSITION SENSOR FAILURE
Are any of the above listed DTCs present?







Yes


No






GO to JF3.


GO to JF4.




JF3 CHECK RESISTANCE OF CRANKSHAFT POSITION SENSOR


  • Measure resistance of crankshaft position sensor.


Is resistance between 290 and 390 ohms (for LS8 between 900 and 1300 ohms)?







Yes


No






GO to JF4.


REPLACE crankshaft position sensor. COMPLETE Misfire Monitor Repair Verification Drive Cycle (REFER to Section 2, Drive Cycles).




JF4 CHECK FUNCTIONALITY OF SUSPECT COIL DRIVER (CD) CIRCUIT


  • Disconnect suspect coil (determined from the table).


  • Connect incandescent test lamp between IGN START/RUN and suspect CD circuit (determined from the table) at the coil on plug harness connector.


  • Disable fuel pump by disconnecting inertia fuel shutoff switch.


  • Observe incandescent test lamp while cranking engine.


Is the test lamp blinking consistently?







Yes


No






KEY OFF. GO to JF5.


KEY OFF. GO to JF6.




JF5 CHECK FUNCTIONALITY OF SUSPECT COIL


  • Remove suspect coil (determined from the table) from spark plug.


  • Connect an air gap spark tester 303-D037 (D81P-6666-A) or equivalent to a suspect coil.


  • Reconnect suspect coil harness connector.


  • Observe spark tester while cranking engine.


Is the spark present?







Yes


No






KEY OFF. INSPECT spark plug, REPLACE if necessary. GO to Z1.


KEY OFF. REPLACE coil. INSPECT spark plug, REPLACE if necessary. COMPLETE Misfire Monitor Repair Verification Drive Cycle (REFER to Section 2, Drive Cycles).




JF6 CHECK IGN START/RUN VOLTAGE TO SUSPECT COIL


  • Key on, engine off.


  • Measure voltage between IGN START/RUN circuit at the coil on plug harness connector and ground.


Is voltage greater than 10.0 volts?







Yes


No






KEY OFF. GO toJF7.


KEY OFF. LS6 and LS8: GO to B5.

All others: IGN START/RUN circuit fault. CHECK condition of related fuses/fuse links. If OK, REPAIR open circuit. If fuse/fuse link is damaged, CHECK IGN START/RUN circuit for short to ground. REPAIR as necessary. COMPLETE Misfire Monitor Repair Verification Drive Cycle (REFER to Section 2, Drive Cycles).




JF7 CHECK SUSPECT CD CIRCUIT FOR OPEN IN HARNESS


  • Disconnect PCM.


  • Measure resistance of suspect CD circuit between PCM harness connector pin (determined from the table) and coil on plug harness connector.


Is resistance less than 5 ohms?







Yes


No






GO to JF8.


REPAIR open circuit. COMPLETE Misfire Monitor Repair Verification Drive Cycle (REFER to Section 2, Drive Cycles).




JF8 CHECK SUSPECT CD CIRCUIT FOR SHORT TO VPWR IN HARNESS


  • Key on, engine off.


  • Measure voltage between suspect CD circuit at the PCM harness connector (determined from the table) and ground.


Is voltage less than 1.0 volt?







Yes


No






KEY OFF. GO to JF9.


KEY OFF. REPAIR short circuit. COMPLETE Misfire Monitor Repair Verification Drive Cycle (REFER to Section 2, Drive Cycles).




JF9 CHECK SUSPECT CD CIRCUIT FOR SHORT TO GROUND IN HARNESS


  • Disconnect scan tool.


  • Measure resistance between suspect CD circuit at the PCM harness connector (determined from the table) and ground.


Is resistance greater than 10,000 ohms?







Yes


No






GO toJF10.


REPAIR short circuit. If symptom or DTC is still present, GO to JF11 to check for damaged coil, otherwise COMPLETE Misfire Monitor Repair Verification Drive Cycle (REFER to Section 2, Drive Cycles).




JF10 PERFORM INTERMITTENT TEST ON SUSPECT CD CIRCUIT HARNESS


  • Connect digital multimeter between suspect CD circuit at the PCM harness connector (determined from the table) and CD circuit at coil on plug harness connector.


  • Wiggle and bend CD harness from PCM harness connector to coil on plug harness connector.


Did resistance fluctuate during wiggle test?







Yes


No






REPAIR intermittent fault in harness. COMPLETE Misfire Monitor Repair Verification Drive Cycle (REFER to Section 2, Drive Cycles).


REPLACE PCM. (REFER to Section 2, Flash Electrically Erasable Programmable Read Only Memory (EEPROM)). If symptom or DTC is still present, GO to JF11 to check for damaged coil, otherwise COMPLETE Misfire Monitor Repair Verification Drive Cycle (REFER to Section 2, Drive Cycles).




JF11 CHECK SUSPECT COIL FOR DAMAGE


  • Remove suspect coil (determined from the table) from spark plug.


  • Connect an air gap spark tester 303-D037 (D81P-6666-A) or equivalent to a suspect coil.


  • Disable fuel pump by disconnecting inertia fuel shutoff switch.


  • Observe spark tester while cranking engine.


Is the spark present?







Yes


No






KEY OFF. INSPECT spark plug, REPLACE if necessary. GO to Z1.


KEY OFF. REPLACE coil. INSPECT spark plug, REPLACE if necessary. COMPLETE Misfire Monitor Repair Verification Drive Cycle (REFER to Section 2, Drive Cycles).

Feb 14, 2015 | 2000 Ford Explorer

1 Answer

I have a 200 1.6 glxi in thailand, have intermittant engine shut down, electrical as all goes off, sometimes instant re start, back fire, and away, otherwise start off the key whilst rolling, i have c


check the battery terminals and posts are shiny clean and tight. Check for loose wires and other terminals that may be dirty or loose.. Have the fault codes read

Mar 25, 2014 | 1998 Ford Laser

1 Answer

2007 accent wont start and has no fire on plugs


Someone would need to check for power and a ground signal at the coils next.

Dec 06, 2012 | 2007 Hyundai Accent GS Hatchback

1 Answer

I have a 1997 Bravada. When it rains the thing will not start. I have replaced the cap and rotor, and the coil. I hear the fuel pump kick on when I turn the key but it still will not start.. Every once in...


Could be the ign. rotor,they have such hot spark,sonetimes the spark actually "drills" a hole thru the plactic and the spark goes to ground at the dist. shaft.
Can't usually even see the tiny hole.
If that is the trouble you will have spark at the coil but nothing coming out of the plug wires,at the cap.
Also check the top bushing in the distrubitor,there should be no play in the shaft,if the bushing goes bad the magnet will hit the pick up coil and kill the spark.

Feb 21, 2011 | 1997 Oldsmobile Bravada

1 Answer

My '91 non turbo Capri won't start. It just "shut off" a couple days ago It would start for a while, then once the tach hit 1.5 it would shut down. I would pull over and restart the cat and it would start,...


Sounds like your computer needs to be replaced, it controls all of the ignition firing order. somethng else, the cam position sensor may be bad also, only 2 other problems I'm aware of in the ignition circuit.

Oct 06, 2010 | 1991 Mercury Capri

1 Answer

No start on old gasoline forklift engine.


most likely the ign switch is ok if you are getting spark. so you have a hot spark at coil and weak fire at plugs? if you have a test light check the positive side of coil for power when turning key on and cranking. if it is dropping power on positive side then ign switch could be bad. can "hotwire" coil by jumping a wire to positive side of coil to pos of battery this will eliminate ign switch.

Apr 07, 2010 | 1978 Chevrolet C1500

1 Answer

Replced the cap & dist coil pac has fire no spark to spark plug


install the new rotor, if that isn't it check the crankshaft position sensor.

Mar 18, 2009 | 1992 Lexus Es 300

1 Answer

Firing Order for Spark Plug Wires for a cavalier v6 93


2.3 and 2.4 has idi ign.syst. mounted directly on top of plugs,2.2 coil pack cylinder numbers are marked on it,from left of elect. connector on coil pack is 2-3-1-4where spark plug wires go,on block, cyl. from drive belt side is 1-2-3-4,timing firing order is1-3-4-2

Mar 15, 2009 | 1998 Chevrolet Cavalier

1 Answer

68 Chevy Celebrity dies whenever it feels like it


No not the magnet, but the coil of wire that it inductes into when it passes, this tells the ignition module to fire the coil. Yes these fail all the time, they are usually ok until they get hot then then go "open"

Aug 21, 2008 | 1986 Chevrolet Celebrity

Not finding what you are looking for?
1990 Mercedes-Benz 190 Logo

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...