Question about 2005 Toyota Corolla XRS

Open Question

How to replace a drive axle seal on the right side of xrs 2005 toyota corrolla

Right side drive axle seal on transmission a 6 speed

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
pakis
  • 86 Answers

SOURCE: 2005 corolla xrs slippage

It could be a case of a worn out clutch pads and lining, There is one adjustment for your clutch it is located under your dash, at the end of your clutch pedals arm and right about where the pedal arm pivots. You adjust it real slow, snall turn makes a big difference. good luck

Posted on Nov 30, 2008

Ad
  • 160 Answers

SOURCE: '93 camry left drive axle replacement problem

the c clip is down u must remove and reposition the openning down

Posted on Mar 16, 2009

  • 41 Answers

SOURCE: removing a drive axle from

if you already have the ball joint dissconnect and the axle out of the steering knuckle just pry out the axle at the transaxle assembly. if it doesnt wont to come out try pushing it in and pry it out vary qiuck pull on the pry bar but they are only held in place with a colasable c-clip just giver.it will come dont worry it wont break

Posted on Mar 22, 2009

Technopro
  • 243 Answers

SOURCE: 2005 Toyota Camry Sportivo brakes making scraping sound.

Hi there,
when the noise is heard, try putting very slight pressure on the brake pedal and see if the noise goes away. If this is the case then definitely the brakes have to be removed and checked again. But if the noise is still present then it's something else doing that noise ans further investigations needs to be carried oput.
Cheers

Posted on Apr 20, 2009

co7196
  • 3433 Answers

SOURCE: 1993 toyota corrolla brake problem My right side

The only other valve that would hold residual pressure is possibly the proportion valve if so equiped. If you follow the brake lines from the master cyl, they will lead yo to a muti port valvethat has all the brake lines on it. Look at the ends of the valve and tell me if there is a pin protruding from one or both ends. If a pin is proyrudingfrom one end and not the other I'll tell you how to fix it.

Posted on Sep 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need recommended Fluid specs and amounts to change oil for 1996 Toyota Tacoma 4 wheel drive front and rear axles


Hello there,

From this page https://www.worldsbestoil.ca/product-cross-reference.php?year=1996&make=TOYOTA&model=TACOMA&engine=2.7L&vin=1



Extract.......

.Engine, 2WD, with filter - 5.4 quarts [1]

Engine, 4WD, with filter - 5.3 quarts [1]

Cooling System, Initial Fill - 9 quarts

AMSOIL Antifreeze and Engine Coolant

Automatic Transmission, A340E Initial Fill - 1.7 quarts

Automatic Transmission, A340F Initial Fill - 2.2 quarts

Automatic Transmission, A43D Initial Fill - 2.6 quarts

Automatic Transmission, Total Fill

4 speed A340F - 10.4 quarts

4 speed A340E - 7.7 quarts

4 speed A43D - 6.9 quarts

Manual Transmission, - 5.3 pints

Differential, With ADRD Front - 2.6 pints

Differential, Without ADRD Front - 2.4 pints

Differential, 2WD Without LSD Rear - 6 pints

Differential, 4WD Extra Long Rear - 4.5 pints

Differential, With LSD Rear - 6.4 pints

Differential, Standard Rear - 6 pints

Transfer Case, - 2.2 pints\'

Sep 13, 2014 | 1996 Toyota Tacoma

1 Answer

I recently replaced my passenger side CV axle as well as the CV axle seal due to a leak. After everything was installed I found I still have a leak and it has actually become slightly worse. The car is on...


It sounds like the inner seal needs to be replaced which means a tear down of the transmission it might be just as easy to replace the tranny but a good repair shop should be able to do this far cheaper.

Oct 28, 2013 | 2005 Pontiac G6 GT

1 Answer

2005 toyota corolla xrs side view mirror


What sources have you tried?
http://www.bing.com/search?q=05+corolla+parts&go=&qs=n&form=QBLH&ghc=0&pq=05+corolla+parts&sc=1-16&sp=-1&sk=

Feb 21, 2013 | 2005 Toyota Corolla XRS

1 Answer

How do you remove toyota timeing chain


Timing Chain and Gears Removal & Installation To Remove:
toy_car_18_gen-p-s-mnts-cvrs-exhst_xp.gif

Except XRS toy_car_18_eng_cmpnts+oil_pmp_loc_1zz-fe_xp.gif

XRS toy_car_18_eng_cmpnts+oil_pmp_loc_2zz-ge_xp.gif

toy_car_18_gen-p-s-mnts-cvrs-exhst_xp.gif

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain cooling system.
  3. Remove the upper front fender apron insulator.
  4. Remove the upper radiator support insulator.
  5. Remove the right front wheel and tire assembly.
  6. Remove the right lower splash shield.
  7. Remove the drive belt and alternator.
  8. Remove the air switching valve (XRS)
  9. Remove the power steering oil pressure switch connector.
  10. Remove the 2 power steering mounting nuts and through bolts. Remove the steering pump from the engine. Secure the steering pump to the cowl toy_car_15_wood_block_on_jack.gif

  11. Raise and support the engine with floor a jack. toy_car_18_eng_rh_mntng_inslt_blts.gif

  12. Remove the right engine mount. toy_car_18_eng_cylndr_hd_cvr_blts.gif

  13. Remove the 2 nuts, 2 clips and the cylinder head shield (except XRS).
  14. Remove the 4 ignition coils.
  15. Remove the 2 ventilation hoses from the cylinder head valve cover.
  16. Remove the 9 bolts, 2 seal washers, 2 nuts, cylinder head cover and gasket (except XRS). XRS toy_car_18_eng_cylndr_hd_cvr_blts_2zz-g.gif

  17. Remove the 4 bolts and the cylinder head shield (XRS).
  18. Remove the 2 nuts, bolt and remove the ventilation hose from the ventilation pipe (XRS). XRS toy_car_18_eng_cylndr_hd_cvr_ventl_hs-pp.gif

  19. Remove the Ventilation pipe and gasket (XRS).
  20. Remove the 9 bolts, wire harness protector. Remove the cylinder head cover and gasket (XRS).
  21. Remove the O-ring from the cylinder head cover (XRS)
  22. Turn the crankshaft pulley and align its groove with timing mark "0" on the timing chain cover. toy_car_18_eng_tmng_mark.gif

  23. Ensure that the marks on the camshaft timing sprockets are in straight line on the timing chain cover surface as shown. toy_car_18_eng_tmng_point_marks.gif

  24. If not turn the crankshaft 1 revolution (360°) and align the marks as above.
  25. Remove the crankshaft pulley toy_car_18_eng_rmv_crnk_sft_pos_snsr_blts.gif

  26. Remove the 2 mounting bolts and remove the crankshaft position sensor.
  27. Remove the mounting bolt, nut and the drive belt tensioner.
  28. Remove the right engine mount bracket.
  29. Remove the front exhaust pipe (XRS).
  30. Remove the Exhaust manifold brace (XRS).
  31. Remove the Exhaust manifold (XRS) toy_car_18_eng_tmng_chn_tnsnr_blts.gif

  32. Remove the 2 mounting nuts and remove the chain tensioner.
  33. Remove the water pump. Except XRS toy_car_18_eng_tmng_chn_cvr_blts_1zz-fe.gif

    XRS toy_car_18_eng_tmng_chn_cvr_blts_2zz-ge.gif

  34. Remove the 11 mounting bolts and nut (except XRS).
  35. Remove the 12 bolts (XRS).
  36. Remove the stud bolt.
  37. Remove the timing chain cover and 2 gaskets.
  38. Remove the crank sensor plate.
  39. Remove the timing chain tensioner slipper mounting bolt. Remove the tensioner slipper. toy_car_18_eng_tmng_chn_sprkt.gif

    Note: If the crankshaft timing sprocket cannot be removed by hand, use 2 screwdrivers. Position shop rags as shown to prevent damage.
  40. Remove the timing chain and crankshaft timing sprocket.
  41. Remove the 2 chain vibration damper mounting bolts. Remove the vibration damper toy_car_18_eng_tmng_cntrl_assy.gif

  42. Hold the camshaft hexagonal section with a wrench. Remove the sprocket mounting bolt.
  43. Remove the valve timing controller assembly and timing sprocket.
Note: Be careful not to damage the cylinder head and valve lifter with the wrench.
Do not disassemble the valve timing controller assembly.

Oct 19, 2010 | 2005 Toyota Corolla

1 Answer

2005 single axle F-350


Yes you will need to pull the axle to get that seal out. You will need to pull tire open punkin or gear case there will be a C clip holding the axle inplace pull this out and very carefully slide the axle out the seal is in the axle housing

Apr 08, 2010 | 2005 Ford F 350 Super Duty

1 Answer

Replacing passenger side mirror on 2005 toyota corolla.


I did exactly that on my Corolla CE recently. Pop the triangular plastic shield out on the inside, remove three nuts, disengage the electric line if you see one and that's it. If you want to get more specifics look the procedure up in the Haynes repair book for Corollas 2003-2005. By the way, the mirrors on Corrollas have, as so often, been constructed by people who never drove these cars. Mirrors get hit on and there should be a joint that allows the mirrors to fold inward. The Corrolla mirrors are still; they have no joint, so when they get hit they push the metal they are mounted on inward and later on you have a poor fit after chnaging them. These American-made Corrollas are in many respect the same **** as other American-made cars.

Jan 11, 2009 | 2005 Toyota Corolla

1 Answer

What is the procedure to replace the drivers side axle (CV joints)on a 1999 Chevy Cavalier. I have the new axle just need the remove and replace procedure


You don't need the special tools that they use in this procedure, you can use a hammer and a block of wood to get the axle out of the hub and you can use a pry bar to get the axle out of the transmisson.



Notice: Care must be exercised to prevent the constant-velocity joints from being over-extended. When either end of the drive axle is disconnected, over-extension of the joint could result in separation of internal components and possible joint failure. Drive axle joints and seals should be protected any time service is performed on or near the drive axles. Failure to observe this can result in interior joint or seal damage and possible joint failure.
Notice: Prior to removal of drive axle assembly, cover all sharp edges in the area of the drive axle with shop towels so that the seal is not damaged during removal.
Removal Procedure
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Place shop towels underneath the outer joint to protect from any sharp edges.

  4. 141983.gif
    tif.gif
  5. Insert a drift (1) into the caliper and the rotor to prevent the rotor from turning.
  6. Remove the drive axle nut (2) and the washer.
  7. Remove the lower ball join from the steering knuckle. Refer to Lower Control Arm Ball Joint Replacement in Front Suspension. If you remove the right axle, turn the wheel to the left. If you remove the left axle, turn the wheel to the right.
  8. Disconnect the wheel speed speed sensor harness. Refer to Wheel Speed Sensor Replacement in Antilock Brake System.
  9. Disconnect the stabilizer link from the lower control arm. Refer to Stabilizer Shaft Link Replacement in Front Suspension.

  10. 442393.gif
    tif.gif
  11. Use the J 28733-B in order to disengage the axle from the hub and the bearing.
  12. Separate the hub and the bearing assembly from the drive axle. Move the strut and the knuckle assembly rearward.

  13. 500285.gif
    tif.gif
  14. Remove the inner joint from the transaxle using J 33008 attached to J 29794 and J 2619-01 for the intermediate shaft, if equipped.
Installation Procedure Notice: Prior to installation of drive axle assembly, cover all sharp edges in the area of the drive axle with shop towels so that the seal is not damaged during installation.
Any time the front halfshaft is removed, the transmission (the halfshaft male and female shank) and the knuckle sealing surfaces should be inspected for debris or corrosion.
If debris or corrosion are present on the sealing surfaces, clean them with a 320 grit cloth or equivalent. Transmission fluid may be used to clean off any of the remaining debris. The surface should be wiped dry, and the halfshaft should be reinstalled free of any debris or corrosion buildup.

    189013.gif
    tif.gif
  1. Install the drive axle (2) into the transaxle (1). Place a non-ferrous drift into the groove on the joint housing and then tap until the drift is seated. Be careful not to damage the axle seal or dislodge the seal garter spring when you install the axle.

  2. 442471.gif
    tif.gif
    Important: Verify that the drive axle is seated by grasping on the inner joint housing and pulling outboard.
  3. Install the drive axle (1) into the hub and bearing assembly (2).
  4. Install the stabilizer link. Refer to Stabilizer Shaft Link Replacement in Front Suspension.
  5. Connect the wheel speed sensor harness. Refer to Wheel Speed Sensor Replacement in Antilock Brake System.
  6. Install the lower ball joint to the steering knuckle. Refer to Lower Control Arm Ball Joint Replacement in Front Suspension.

  7. 141983.gif
    tif.gif
    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  8. Install the washer and the new drive axle nut (2).
  9. Insert a drift (1) into the caliper and the rotor in order to prevent the rotor from turning.
    Tighten
    Tighten the drive axle nut to 200 N·m (144 lb ft).
  10. Install the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  11. Lower the vehicle

Aug 02, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
2005 Toyota Corolla XRS Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...