Question about BMW X5 Series

Open Question

2003 BMW WINDSHIELD WIPER DOES NOT WORK

FUSE, RELAY AND MOTOR IS GOOD

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
dddsouve
  • 64 Answers

SOURCE: windshield wipers in front wont work but rear wipers work

Hi! U need to check the switch and the wiring circuit that controls the motor.

Posted on Jan 15, 2009

Ad
  • 840 Answers

SOURCE: Rear Windshield Wiper Problems

Check the wiper motor connection if its touching anything and loose it will automatically ground out and check at connection make sure you put some gel and then snap it in/ Please rate my response thank you very much

Posted on Jan 31, 2009

  • 112 Answers

SOURCE: horn, windshield wiper not working, new fuse

Before you go to the relay--see if you can scrub the fuse holders clean (for the horn and wipers). Remove the ceramic fuses, and take a stiff bristled brush and some rubbing alcohol to the contact surfaces. Vehicles I used to restore (from the South) that had been sitting a while had green oxidation on the fuse contacts that would cause intermittent opens on the circuit.

Posted on Mar 27, 2009

  • 1168 Answers

SOURCE: windshield wipers don't work.Fuse is good.

Hello Firerocker.
If your washer motor works there is power in the circuit and ground.
The wiper motor housing needs to be grounded.
If neither one works check for power on the green wire leading into the motor. If nothing there your switch may be bad.
If there is power to the green wire then check for power on the gray wire on low wiper speed and power on purple on high speed.
Here is a diagram if you need it.

http://i28.photobucket.com/albums/c227/Kiltylake/Wiper.gif

Hope this gets your wipers going again.

KL


Posted on Feb 12, 2010

  • 92 Answers

SOURCE: 2003 f250 6.0 diesel windshield wiper just stopped

The wiper system in your vehicle is a simple system. Most of the electronics are in the wiper motor. There are 2 fuses on the interior fuse panel. Fuse #106 and fuse #33. I would start by testing for voltage at the wiper motor connector. Pin #5 (dark green wire) and pin #8 (black and pink wire) should both have voltage present with the key on. If voltage isn't present on both wires then you will have to trace the wires back to the fuse panel. Next test the 2 ground wires pin#3 (pink and orange wire) and pin#6 (black wire). Connect your test light to the positive battery terminal and probe the 2 ground wires. If the ground is good the test light will light.
The other thing I would check is the connectors on the multifunction switch. Sometimes the wires will pull right out of the connectors, this happens more on steering columns with tilt. Pull on each wire to be sure they are tight in the connector shell.
I would also check connector c145. A black 16 pin connector located on the drivers side of the engine compartment along side 4 other similar connectors on a plastic bracket (behind wheel well). Examine all the wiring near the connector also.
I hope this helps!

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I find out if the wipers on my 2006 H3 Hummeris on a relay?


The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Low Speed Operation
When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. The body control module (BCM) monitors the windshield wiper switch signal 1 circuit, and energizes the wiper micro relay which will operate the windshield wiper motor. The wiper motor will operate at low speed, since the wiper 2 relay is de-energized. Low speed can also be commanded with a scan tool, by commanding Wiper Relay Cmd. ON and OFF. Refer to Scan Tool Output Controls .
High Speed Operation
In the High position, the windshield wiper/washer switch supplies voltage to both the wiper micro relay and wiper 2 relay coils. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. The windshield wiper motor will operate at high speed. During high speed wiper motor operation the wiper switch signal circuit is at the low speed signal voltage, and the body control module (BCM) supplies redundant voltage to the wiper relay via the wiper diode.

This info is out of hummer factory service manual !

Dec 10, 2016 | 2006 Hummer H3

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

3 Answers

My f250 2003 wipers and pump dont work iv replaced switch and wiper moter fuses are good the 2 i could locate for wipers


Have you done a Probe Test on the vehicle? A Probe Light Tester can help you locate a short in your cars electrical system. To learn what a Probe Tester is and How to use it, watch the following video: https://www.youtube.com/watch?v=tXzKcEyIOq8

Dec 22, 2015 | Cars & Trucks

1 Answer

I'm driving in rain, wipers working good, all of a sudden they quit! I drive for 15 min, check again, they work for a while, then quit again...what in the problem?


If your not familiar with automotive electronics an module control of components , I suggest you take it to the dealer . They have the tools to diagnose this type problem !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch


?€¢
Body control module (BCM)


?€¢
Wiper PCB relay


?€¢
Wiper high PCB relay


?€¢
Windshield wiper motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
WPR fuse 25 A


?€¢
WSW fuse 10 A


Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
High Speed Operation When the wiper switch is in the high speed position, ground is applied through the windshield wiper switch high signal circuit to the body control module (BCM) indicating the wiper high speed request. In response to this signal, the BCM then energizes the wiper PCB relay, as stated above, and the wiper high PCB relay by applying ground through the control circuit to the coil side of the relay. With the wiper high relay energized and its switch contacts closed to the high speed control circuit of the wiper motor, the motor will operate at high speed.
Wiper motor high speed operation and the wiper high speed PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
You could Have a switch problem , BCM problem ,PCB relay problem , the pcb relays are non serviceable an the whole under hood fuse box would need to be replaced . Malfunctioning motor bad ground some where etc.....

Dec 20, 2015 | 2008 Chevrolet Impala

1 Answer

Replacing wiper linkage


WINDSHIELD WIPERS


It can be faulty wiper motor or blown wiper control fuse.


Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring: -----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below: -------


1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

Nov 29, 2012 | 2003 Chevrolet Cavalier

1 Answer

Where is fuse for wiper fluid pump on a 2003 cavalier?


It can be faulty wiper motor or blown wiper control fuse.


Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

Nov 28, 2012 | 2001 Saturn S-Series

1 Answer

Fix 2005 tahoerear wiper


For wiper problem,troubleshooting,check the help links provided below.Click the link to go through its procedure:----------------
HOW TO REPLACE A WINDSHIELD WIPER MOTOR

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

---------
Wipers not working, but hear relay click? http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html--------- Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

-----------------
How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html


------------

Where is wiper fuse located?

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html


-----------

Complete wiper components replacing details for Car Models? http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html The wipers not working? http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

Mar 01, 2012 | 2003 GMC Yukon

1 Answer

Windshield wipers will not work fuse is good can hear windshield wiper motor is thier a relay switch


Sometimes, the bolts come loose. I would see if they need to be tightened.

Feb 04, 2011 | 2003 Ford Focus

1 Answer

Windshield wipers


From your owners manual:

Fuse#11 30A , Wiper Run/Park
Relay, Wiper Hi/LO Relay, Windshield Wiper
Motor, Rear Washer Pump Relay

U will also need to check the relays if the fuse is ok, the relay, it is the underhood fuse box
Relay #202 — Front Wiper Run/Park Relay

Dec 18, 2008 | 2001 Lincoln Navigator

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...