Question about Chevrolet Silverado

Open Question

How to remove heater core housing on 1981 chevy truck

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: 1999 S10 Chevy truck

you will have to remove the dash assembly and then the heater/a/c box it is in the hvac module.

Posted on Oct 02, 2008

Shouldibuyit
  • 44 Answers

SOURCE: replace heater core 1994 chevy g20 conversion van

Here a are the instuctions to remove it. I did not know if you have A/C or not so I included both for you.

REMOVAL & INSTALLATION
Without Air Conditioning
ALL MODELS
See Figure 1

  1. Disconnect the negative battery cable.
  2. Remove the coolant recovery bottle.
  3. Place a pan under the van and disconnect the heater intake and outlet hoses. Quickly remove and plug the hoses and support them in an upright position. Drain the coolant from the heater core into the pan.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw. Remove the duct.
  2. Remove the engine cover.
  3. Remove all the instrument panel attaching screws.
  4. Carefully lower the steering column. Raise and support the right side of the instrument panel. Refer to for further details.
  5. Remove the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  6. Disconnect the temperature door cable. Carefully fold the cable back and out of the way.
  7. Remove the three nuts from the engine compartment side of the distributor case and the screw from the passenger compartment side.
  8. Remove the heater case and core assembly.
  9. Remove the core retaining straps and remove the core.
To install:
  1. Install the core.
  2. Install the core retaining straps.
  3. Install the heater case and core assembly.
  4. Fasten the three nuts on the engine compartment side of the distributor case and the screw on the passenger compartment side.
  5. Connect the temperature door cable.
  6. Install the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  7. Install the steering column.
  8. Fasten all the instrument panel attaching screws.
  9. Install the engine cover.
  10. Install the duct. Install the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw.
  11. Connect the heater intake and outlet hoses.
  12. Fill the cooling system.
  13. Install the coolant recovery bottle.
  14. Connect the negative battery cable.
1990-95 MODELS With A/C

  1. Disconnect the battery ground cable.
  2. Remove the engine cover.
  3. Remove the steering column-to-instrument panel bolts. Lower the column carefully.
  4. Remove the upper and lower instrument panel attaching screws. Remove the radio support bracket screw.
  5. Raise and support the right side of the instrument panel.
  6. Remove the lower right instrument panel bracket.
  7. Remove the vacuum actuator from the kick panel.
  8. Disconnect the temperature cable and vacuum hoses at the case. Remove the heater distributor duct from over the engine hump.
  9. Remove the two defroster duct-to-firewall attaching screws below the windshield.
  10. Under the hood, disconnect and plug the heater hoses at the firewall.
  11. Remove the three nuts and one screw (inside) holding the heater case to the firewall.
  12. Remove the case from the van. Remove the gasket for access to the screws holding the case together. Remove the temperature cable support bracket. Remove the screws and separate the case. Remove the heater core.
To install:
  1. Install the heater core.
  2. Assemble the case and fasten the screws.
  3. Install the temperature cable support bracket.
  4. Position the gasket, then install the case in the van.
  5. Fasten the three nuts and one screw (inside) holding the heater case to the firewall.
  6. Connect and plug the heater hoses at the firewall.
  7. Fasten the two defroster duct-to-firewall attaching screws below the windshield.
  8. Install the heater distributor duct.
  9. Connect the temperature cable and vacuum hoses at the case.
  10. Install the vacuum actuator at the kick panel.
  11. Install the lower right instrument panel bracket.
  12. Fasten the radio support bracket screw.
  13. Fasten the upper and lower instrument panel attaching screws.
  14. Fasten the steering column-to-instrument panel bolts.
  15. Install the engine cover.
  16. Connect the battery ground cable.
  17. Refill the cooling system as necessary.

Posted on Nov 28, 2008

  • 4 Answers

SOURCE: how to remove heater core on 97 chevy blazer

drop column, pull back dash. there is a cover that comes off and exposes the core

Posted on Apr 06, 2009

gripfitter
  • 557 Answers

SOURCE: heater core on 2000 chevy truck

Thats a real job. The heater core is in the case that is behind the glove box. Pretty much the dash has to come out so you can separate that case to remove th heater core.

Posted on Oct 04, 2009

wyno62
  • 364 Answers

SOURCE: how do i replace a heater core on a 1988 chevy

You wll need to first undo the heater hoses at the firewall to the core, then under the dah you will need to dismantle the heater box, the core is located inside this box, assembly is the reversal, heater core is about $40. time consuming and hard on the back but not hard. Remember we are here to give as much help as we can without seeing the car so, I hope this helps somewhat, good luck.

Posted on Dec 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change the heater core in a 2001 chevy 1500


If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Jan 09, 2011 | 2001 Chevrolet Silverado 2500

1 Answer

How to get to the heater core in my 1988 chevy s10


If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Jan 08, 2011 | 1988 Chevrolet S-10

1 Answer

What is the process to putting in heater core in 1983 chevy silverado?


If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Jan 06, 2011 | 1983 Chevrolet Silverado

1 Answer

Where is the heater core at on a 1999 chevy malibu with the 3100 in it


If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 31, 2010 | 1999 Chevrolet Malibu

1 Answer

How do u replace a heater core in a 1994 chevy g20 conversion van


If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 23, 2010 | 1994 Chevrolet G20

1 Answer

Need to replace heater core on 1997 Chevy Lumina


If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 23, 2010 | 1997 Chevrolet Lumina

1 Answer

How do i remove heater core


If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 14, 2010 | 1981 Chevrolet Corvette

1 Answer

How do i change the heater core on my 1999 chevy silverado 1500?


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 11, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

How do you change a heater core on a 1983 chevy truck?


Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Nov 26, 2010 | 1983 Chevrolet Silverado

1 Answer

Is the heater core on a 1981 bronco in the engine compartment or the cab compartment


in the cab, but procedures are different depending on whether or not you have A/C. See below

1980-81 Comfort Vent Heaters, Without Air Conditioning
  1. Disconnect the heater hoses from the heater core tubes and plug the hoses with suitable 5 / 8 inch; (16mm) plugs.
  2. Remove the glove compartment liner.
  3. Remove two (2) spring clips attaching the heater core cover to the plenum along the top edge of the heater core cover.
  4. Remove eight (8) screws attaching the heater core cover to the plenum and remove the cover.
  5. Remove the heater core from the plenum taking care not to spill coolant from the core.
To install:
  1. Install the heater core in the plenum.
  2. Install the heater core cover (eight (8) screws and two (2) spring clips along the top edge of the cover).
  3. Install the glove compartment liner.
  4. Connect the heater hoses to the heater core. Tighten the hose clamps.
  5. Add coolant to raise the coolant level to specification.
  6. Check the system for proper operation and for coolant leaks.

1980-81 Standard & High Output Heaters, Without Air Conditioning
  1. Disconnect the temperature cable from the temperature blend door and the mounting bracket on top of the heater case.
  2. Disconnect the wires from the blower motor resistor and the blower motor.
  3. Disconnect the heater hoses from the heater core and plug the hoses with suitable 5 / 8 inch; (16mm) plugs.
  4. Working under the instrument panel, remove two (2) nuts retaining the left end of the heater case and the right end of the plenum to the dash panel.
  5. In the engine compartment, remove one (1) screw attaching the top center of the heater case to the dash panel.
  6. Remove two (2) screws attaching the right end of the heater case to the dash panel, and remove the heater case from the vehicle.
  7. Remove nine (9) screws and one (1) bolt and nut attaching the heater housing plate to the heater case, and remove the heater housing plate.
  8. Remove three (3) screws attaching the heater core frame to the heater case and remove the frame.
  9. Remove the heater core and seal from the heater case.

To install:
  1. Position the heater core and seal in the heater case.
  2. Install the heater core frame (3 screws).
  3. Position the heater housing plate on the heater case and install the nine (9) screws and one (1) bolt and nut.
  4. Position the heater case to the dash panel and install the three (3) attaching screws.
  5. Working in the passenger compartment, install two (2) nuts to retain the heater case and plenum right end to the dash panel.
  6. Connect the heater hoses to the heater core. Tighten the hose clamps.
  7. Connect the wires to the blower motor resistor assembly.
  8. Connect the blower motor wires.
  9. Position (slide) the self-adjusting clip on the temperature cable to a position approximately one 1 inch; (25.4mm) from the cable end loop.
  10. Snap the temperature cable on the cable mounting bracket of the heater case. Then, position the self-adjusting clip on the door crank arm.
  11. Adjust the temperature cable.
  12. Check the system for proper operation.

Oct 05, 2010 | 1981 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...