Question about 2004 Chevrolet Malibu Maxx

Open Question

My abs light n tc light came on how do i reset them

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Airbag light reset code


You would need to reset the warning light and then see if it comes back on, which would indicate a fault still there. Try this procedure

http://s16.photobucket.com/user/rogersb/media/AirBagReset.jpg.html

"How do you reset the airbag warning light in a '94 Camry?
A: Clearing the warning light in '92-'96 Camrys by the following procedure:
In the DLC1 or DCL2 (data link connector under the hood, see following diagram)
Use two short wires, one wire at terminal TC and a different wire at terminal AB
With the ignition key ON - wait 6 seconds, then:
Ground terminal TC to good body ground for one second
Then ground terminal AB for one second
Then TC one second
Then AB one second
Then ground TC until the light blinks.
Make sure the interval between grounding terminals is not more than 0.2 sec.
Remove the ground wires
Be very careful to only use the correct terminals."

Jan 21, 2014 | Toyota Cars & Trucks

1 Answer

1995 toyota camry LE airbag light on


Easy, just listen carefully. Get two wires and attach them to a good ground (-12v). These need to be solid and small, like telephone wire. Attach both to ground and strip off the insulation so that you can insert them into your data connection port. Just make sure they will fit and make contact, but don't touch them to any of the contacts yet. Ok, now with the key "on", look at the data connector, they should have letters on them, we will be looking for "ab" and "tc".

  1. with key on, ground tc for 1 second
  2. ground ab for one second
  3. ground tc for 1 second
  4. ground ab for 1 second
  5. ground tc for 1 second
Light should be out. If this don't work, instead of 1 second, try 1.5 seconds, but shut off key and turn back on before you try again.

Took me two trys personally. Here is a pic of what I believe to be your connector.
:7bbffe61-366d-4978-87bc-95b69b376249.jpg

Dec 16, 2013 | Cars & Trucks

1 Answer

Airbag light on


Try this procedure, but if it comes back on, your airbag is faulty, of course.
A: Clear the warning light in '92-'96 Camrys by the following procedure:
In the DLC1 or DCL2 (data link connector under the hood, see following diagram)
Use two short wires, one wire at terminal TC and a different wire at terminal AB
With the ignition key ON - wait 6 seconds, then:
Ground terminal TC to good body ground for one second
Then ground terminal AB for one second
Then TC one second
Then AB one second
Then ground TC until the light blinks.
Make sure the interval between grounding terminals is not more than 0.2 sec.
Remove the ground wires
Be very careful to only use the correct terminals.
cc08c9a7-2326-431d-84b4-ab8f01d33743.jpg

Jun 23, 2013 | 1993 Toyota Camry V6

1 Answer

Why dose the tc light stay on my 02 cavalier


If the abs light is on there is a code set in the abs system. When a code sets it disables tc and abs. You need to have it scanned for codes

Mar 18, 2013 | 2000 Chevrolet Cavalier

2 Answers

Air bag reset 1995 toyota camry


I haven't had to try this but here is a procedure for resetting the airbag after the battery was disconnected


"How do you reset the airbag warning light in a '94 Camry?


A: Clearing the warning light in '92-'96 Camrys by the following procedure:
In the DLC1 or DCL2 (data link connector under the hood, see attached diagram):
Use two short wires, one wire at terminal TC and a different wire at terminal AB:
With the ignition key ON - wait 6 seconds, then:
Ground terminal TC to good body ground for one second
Then ground terminal AB for one second
Then TC one second
Then AB one second
Then ground TC until the light blinks.
Make sure the interval between grounding the terminals is not more than 2 secs.
Remove the ground wires.




Be very careful to only use the correct terminals.
8_11_2012_5_40_39_am.jpg

Aug 05, 2012 | 1995 Toyota Camry

1 Answer

How reset the abs check light on a 2007 scion tc


not sure you can reset this, you can try to pull the fuses, under hood number 10 and 11, but installing them back may bring the problem back, you may need a new anti lock system

Jun 07, 2012 | 2007 Scion tC Coupe

1 Answer

ABS LIGHT AND TRACTION CONTROL LIGHT STAYS ON


ABS = Anti-lock Brake System.
TC = Traction Control System (Engine Control Module).
If the ABS lights on the dashboard permanently the ABS system is faulty. You must access the ABS & TC Electronic Control Units (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ABS ECU, in other words reset the ABS system and turn off the warning lamp on dashboard.

I suspect bad brake pedal switch, but you should scan the ABS & TC ECU's.

Jul 02, 2011 | 2001 Jaguar XJ8

1 Answer

Tc whont turn on the light wont turn off abs light wont turn off


Your ABS system has detected a fault in the system. When that happens, the TC is automatically turned off. You will have to have the ABS diagnosed and repaired before the TC will come on again.
Good luck.

Jan 17, 2011 | 2005 Hummer H2

2 Answers

My tc and abs light are coming on all the


Speedo and traction control; check wheel sensors all 4, clean and blow the sensors and reactor rings.
Is ABS light on as well? if so, you need a EBTCM module mounted to the brake ABS pump facing the battery. There are places in the US that rebuild them with warranty for under $150.

Apr 26, 2010 | 2000 Cadillac Catera

1 Answer

THE TC light had a wrench beside it? And the TC light says the TC is off and the ABS light is now lit up. I tried pushing the button to turn the TC on and Off but this makes no difference


chances are there is a problem in the abs system, which also controls the traction control. have the car scanned for codes, which will give you a starting point for diagnosing. good luck!

Dec 22, 2009 | 2002 Pontiac Aztek

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...