Question about 1989 Chevrolet S-10 Blazer

1 Answer

No heat in 1989 chevey s10 blazer - 1989 Chevrolet S-10 Blazer

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 256 Answers

Change the thermostat in it,

Posted on Dec 04, 2012


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1985 Answers

SOURCE: 1989 Chevy S10 Blazer, 4.3L V6. 4wd not working.

under the battery is where you need to check first,then follow it down around the right front wheel well,

Posted on Dec 09, 2009

  • 193 Answers

SOURCE: Rear disc brake conversion on a 1989 S10 Blazer

They have different master cylinders and different proportioning valves. Other than that, it's a slam dunk.

Posted on Mar 03, 2010

  • 3917 Answers

SOURCE: pictures or illustrations/diagrams of 1989 blazer heater core


Please check this webste:

Please accept if this helped you.


Posted on Mar 28, 2010

  • 973 Answers

SOURCE: 1989 chevy s10 blazer will not start no spark

Did you check to see if your fuel pump is working, sending fuel to the engine when you are cranking the starter?

Posted on Jun 04, 2010

  • 14036 Answers

SOURCE: what reading for map sensor chevy blazer s10 1989


Posted on Jun 24, 2010

Testimonial: "Thanks for the answer. I appreciate your help."

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rear end axel diagram

found in the workshop manual under rear axle

Apr 16, 2017 | Cars & Trucks

1 Answer

1989 cevrolet s10 4 cylinder 2.5 engine idles idles to high for to long when first started

check the setting on the automatic choke . loosen the 3 screws on the mounting ring and turn the cap a few points to allow the choke to come off earlier.. If it is heated by pipes from the manifold ensure that the hot air is getting to the choke operating bi-metal spring. If electric ensure that the current is getting to the heater in the cap.

Dec 18, 2013 | 1994 Chevrolet S-10 Blazer

1 Answer

Can i install my new 350 sbc in my 1989 s10 blazer 4x4 without the oilpan bolted up

you will need to have the oil pan on, its pretty tight when you put in a 350 ,also a 3" body lift will make things alot smoother godbless

Apr 16, 2013 | 1989 Chevrolet S-10 Blazer

1 Answer

1989 chevey blaser fan will not blow.

Yes, the 1984 Rampage does have a fan clutch. When it engages at lower RPMs, it helps to keep proper airflow through the radiator and A/C condenser. Typically, it disengages as you pick up speed (and quiets down) but reengages again when you come back down to idle for a while. -------------------------------------------------------------------

Dec 04, 2012 | 1989 Chevrolet S-10 Blazer

1 Answer

1989 chevey s10 blazer hard time shifting into gears

The problem and the solution is clutch master cylinder and a slave cylinder

Mar 28, 2012 | Cars & Trucks

1 Answer

My 1989 s10 blazer wont idle

Check for plugged ctalitic converter

Jul 23, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

1989 s10 4 3 4x4 blazer the amp goes down why

Sounds like loose or faulty Alternator connection try cleaning and retightening cable connections. also check that battery connections are clean and tight. GL

Jun 09, 2009 | 1989 Chevrolet S-10 Blazer

1 Answer

Trying to find a repair manual for a 1989 Chevrolet S10 Blazer

If you can't find a free one go to They buy and sell dealer service manuals for a reasonable price. Mine cost me $49 plus shipping.

Jun 04, 2009 | 1988 Chevrolet S-10

1 Answer

Wiper module

You have a panel on the fire wall where the wiper motor is connected. There is a 3" by 3" panel on the wiper assembly is connect to. It is helt on 3 to 4 torque bit screws. behind there is the module panel electronic board. Just change it out, or get a magnifie glass and you will see a crack solder. Put flux on the crack and heat up with solder iron, and you will fix it yourself.

Jan 08, 2009 | 1989 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides