Question about 2004 Nissan Quest

2 Answers

2004 nissan quest

I have a 2004 nissan quest 3.5 engine it reads code p0328 knock sensor will this be the cause for the engine to crank but not start after driven for 15 to 20 minutes , and than after 10 to 15 minutes start again? can somebody please tell me how ca i fix this problem

Posted by on

  • teds repairs
    teds repairs Dec 04, 2012

    thank you for rating my answer. I have rebuilt 4 of those motor so far

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,101 Answers

Yes it can stop the motor from running. it is located under the intake malifold between the cylinder heads

Posted on Dec 04, 2012

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I am not sure how many ignition coils your van has but it is possible your coil is going out and it shuts down when it over heats and when it cools down it stars again ,

Posted on Oct 23, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 76164 Answers

SOURCE: pls tell me

the knock sensor is located near the bottom of the engine block, it is screwed into the blocks water jacket, so make sure u drain the radiator before u change it, also it must be torqued to a specific value or it will not function correctly.

Posted on Mar 22, 2009

co7196
  • 3433 Answers

SOURCE: 2004 Nissan Quest - Engine chatter/knocking

Ther e is a chance your injectors are leakin g down and there is excess fuel in the cylinders. Not a good thing. So, you fuel pressure and injectors need chkg. good luck

Posted on Jun 09, 2009

  • 291 Answers

SOURCE: Nissan Quest/Knock Sensor

n ot enough info to determine....... now what speed sensor.. one is the vehicle spped sensor to operate the speedodometer.. the other is for the engine speed for timming of motor..

Posted on Sep 04, 2009

Villager96
  • 99 Answers

SOURCE: 1996 nissan quest. car wont start and just keeps

Have a bad knock sensor on my 06 villager and no problem driving it daily, most likely you may have a coil problem, fuel pump or MAF sensor problem. Hope this works

Posted on Jan 11, 2010

  • 73 Answers

SOURCE: Understanding trouble codes for my vehicles

On the Nissan that code means you have a short in the knock sensor circuit or you just need a new knock sensor.

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i deal with Error Code P0328


the following information courtesy of OBD-CODES.com P0328 Knock Sensor Circuit High Input OBD-II Trouble Code Technical Description Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) What does that mean? Knock sensors are used to detect engine pre-detonation (engine knock or ping). The knock sensor (KS) is usually a two wire sensor. A 5 volt reference is supplied to the sensor and there is a signal return from the knock sensor to the PCM (powertrain control module). The sensor signal wire informs the PCM when a knock occurs and in what degree of severity. The PCM will retard the spark timing to avoid pre-detonation. Most PCMs have the ability to learn spark knock trends in the engine during normal operation. A P0328 code is a generic DTC, thus it applies to all makes of vehicles, and refers to a high output voltage of the knock sensor. In many cases, this means the voltage is above 4.5V but that specific value depends on the specific make and model of vehicle. This code refers to the sensor on bank #1. Symptoms Symptoms of a P0328 DTC may include: MIL (Malfunction Indicator Lamp) illumination Audible knocking from the engine compartment Pinging from engine under acceleration Loss of power Irregular RPM Causes Potential causes of a P0328 code include: Knock sensor connector is damaged Knock sensor circuit is open or shorted to ground Knock sensor circuit is shorted to voltage Knock sensor has failed Loose knock sensor Electrical interference in circuit Low fuel pressure Incorrect fuel octane Mechanical engine problem Failed/faulty PCM Possible Solutions If you can hear engine knock (detonation), first fix the source of the mechanical problem and retest. Ensure the correct octane fuel was used (some engines require premium fuel, check the owners manual). Aside from that, for this code, most likely the problem will lie either with the knock sensor itself or the wiring & connectors going from the sensor to the PCM. Realisitcally, for the DIY vehicle owner, the best next steps are to measure the resistance between the two knock sensor wire terminals where they go into the PCM. Also, check the voltage of the same terminals. Compare those numbers to the manufacturer's specifications. Also, check all wiring and connectors leading from the knock sensor back to the PCM. In addition, you should also check the resistance using a Digital Volt Ohm Meter (DVOM) of the knock sensor itself, compare it to the vehicle manufacturers specification. If the knock sensor resistance value is out of spec, then it needs to be replaced. Other knock sensor DTCs include P0324, P0325, P0326, P0327, P0328, P0329, P0330, P0331, P0332, P0334 Register now to ask a question (free) Related P0328 DTC Discussions

Read more at: http://www.obd-codes.com/p0328
Copyright OBD-Codes.com

Aug 17, 2015 | Cars & Trucks

1 Answer

I am workimg on my 2000 nissan quest. it cranks and turns over but will not start. it is throwing codes P0340 twice and P0325. we replaced the distributor cap and rotor and still nothing. probably goi


P0325 Knock Sensor 1 Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
P0326 Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329 Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
P0330 Knock Sensor 2 Circuit (Bank 2) -Circuit Malfunction
P0331 Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332 Knock Sensor 2 Circuit Low Input (Bank 2)
P0333 Knock Sensor 2 Circuit High Input (Bank 2)
P0334 Knock Sensor 2 Circuit Input Intermittent (Bank 2)
P0335 Crankshaft Position Sensor -Circuit Malfunction
P0336 Crankshaft Position Sensor -Range/Performance
P0337 Crankshaft Position Sensor -Low Input
P0338 Crankshaft Position Sensor -High Input
P0339 Crankshaft Position Sensor -Intermittent
P0340 Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
sorry would a play with this to know for sure ,check the wiring plugs onto the sensors to make sure their not full of oil or corroded

Aug 07, 2014 | 2000 Nissan Quest

1 Answer

2004 nissan xterra run great for 12 miles then misfiring,cnt get over 45 miles an hour. codes p 0733,p0420,p0430,p0328 comes up. new wires,new cap,rotor spark plugs 6 months old timming belt 6 months...


code p0733 refers to gear 3 -incorrect ration===causes---wiring---TR sensor/switch--shift solenoids---transmission mechanical fault
code p0420 refers to catalytic converter system -bank 1---efficiency below threshold===causes--cat converter--wiring--HO2s 2
code po430 refers to cat converter system bank 2--efficiency below threshold===causes--cat converter--wiring ---HO2s 2
code p0328 refers to knock sensor (KS) 1 bank 1--high input===causes--wiring short to positive--KS incorrectly tightened--KS---ECM

basically replace the cat converters as they are blocking the exhaust system and preventing your over 45mph problem
replace the TR sensor/ switch as you have not mentioned a transmission problem
Rectify the problem with the KS as it controls the air/fuel mixture setting which contributes to the car getting hot.

Jan 12, 2014 | Nissan Cars & Trucks

1 Answer

Temp sensor


I'm not a 100% but it sounds like your camshaft position sensor went bad then caused the other codes to come up because the camshaft position sensor tells the computer how much gas it needs. So it started a chain reaction with the fuel level sensor, fuel temperature sensor, and knock sensor codes. The Fuel temp. sensor helps the engine to know how much fuel to inject as well depending on the temp. of the fuel. The fuel pressure sensor senses the amount of fuel in the fuel rail by reading the internal pressure of the rail, so that's what leads me to believe that it's your camshaft position sensor. Particularly if that was the first code that came up. Hope this helps you.

Aug 27, 2013 | Nissan Xterra Cars & Trucks

2 Answers

Car died. Cranks, but wont start. Codes P0328, P0340


Yes, if the camshaft position sensor has failed, your vehicle won't start.

Jun 11, 2013 | 2004 Nissan XTerra

1 Answer

I have a 2002 Nissan frontier SC, 69000 miles. Motor runs well when first start the engine and runs very routh after warm up and it just stops sudenly the engine. Three codes P0328(knock sensor 1 circ


P0328 Is knock sensor code,all Nissan have this code so leave,concentrate on P0101 and P0103 this is MAF(mass airflow),Just make sure the timing belt is in good condition and the marks are correct, your solution is NTB02-003A In other word you need a reprogram on the ECM

Mar 19, 2012 | 2000 Nissan Frontier

1 Answer

1996 nissan quest. car wont start and just keeps trying to crank. it has a knock sensor code that i pulled out of the dtc. it has no injector pulse and we are trying to figure out if the knock sensor...


Have a bad knock sensor on my 06 villager and no problem driving it daily, most likely you may have a coil problem, fuel pump or MAF sensor problem. Hope this works

Jul 29, 2009 | 1996 Nissan Quest

2 Answers

2004 Nissan Quest - Engine chatter/knocking


Ther e is a chance your injectors are leakin g down and there is excess fuel in the cylinders. Not a good thing. So, you fuel pressure and injectors need chkg. good luck

Jun 09, 2009 | 2004 Nissan Quest

Not finding what you are looking for?
2004 Nissan Quest Logo

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...