Question about 1994 Jeep Grand Cherokee

1 Answer

Turn signals I need to replace the turn signal bulbs and have no idea how to access them.

Posted by on

  • wrichardson1 May 11, 2010

    is this the front lights or rear?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The ones on the rear you have to lift the tailgate and remove the lenses to access the bulbs

Posted on Jan 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 nissan sentra neither one of my turn signal bulb are working tried replacing the bulbs that didn't work.also tried switching the pigtail that didn't work either any idea what the problem


I had this problem with my car. Is ur hazzard flasher working? if they are working and the turn signals are not working. Try replacing the hazzard light switch. If the hazzard are not working then the combination flasher unit is bad. its what controls the signals and flasher.

Nov 10, 2012 | 2001 Nissan Sentra

1 Answer

I am trying to replace aleft rear turn signal bulb on a 2005 lacrosse. I removed two wing nuts but cannot remove assmbly. Is there another wing nut holding it in. I cannot find it?


3 wing nuts. here is the info needed.

gmlogoflat.gif Service Information
bhome.gifbpublication.gifbnumsrchbutton.gifbnews.gifymkbutton.giffeedback.gifbhelp.gif
2005 Buick LaCrosse ' Allure, LaCrosse VIN W Service Manual ' Body ' Lighting Systems ' Repair Instructions ' Document ID: 1537542 Tail Lamp, Turn Signal Lamp, High Mount Stop Lamp, License Lamp, Backup Lamp Replacement - Rear
1537540.gif
tif.gif
Callout
Component Name
Notice: Refer to Fastener Notice in the Preface section.
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .
Turn Signal/Stop Lamp Assembly Replacement - Rear 1
Nut, Turn Signal/Tail Lamp (Qty: 3)
Tip
Pull back rear compartment carpet to gain access to lamp.
Tighten
2 N·m (18 lb in)
2
Lamp, Turn Signal/Tail Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.
License Lamp Replacement 3
Screws, License Lamp (Qty: 2)
Tighten
2 N·m (18 lb in)
4
Lamp, License Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.

Jul 29, 2011 | Buick LaCrosse Cars & Trucks

1 Answer

How do I access left rear turn signal to replace bulb


need to replace turn signal bulb. How to access? pulled out piece of foam out of approx. 2" hole that feed wires go thru...............

Jul 09, 2010 | 2000 Ford Expedition

1 Answer

2000 Cavalier: replacing signal bulb on 99 cavalier drivers side ...


remove the mounting screw on the lens, then remove the top 2 bolts holding the headlamp, pull headlamp out to gain access to the mounting nut on the turn signal. Remove the nut and the turn signal light will pull straight out allowing you to replace the bulb.

May 17, 2010 | 2000 Chevrolet Cavalier

1 Answer

How do I change my front turn signal? I can access the lower signal from under the bumper, I can't access the signal that is next to the headlight. There are no screws in front to take the plate off,...


The signal light on the grill next to the head light can be accessed by removing the the front grill. Your going to need a torque screw driver to remove the grill to get to the light bulb. The signal from under the bumper can be accessed from behind the bumper and you need not to take the turn light assemble off from the bumper. There are LED light bulbs available now and last much longer then the conventional bulbs and cost not that much more. Auto Zone carries these replacement LED bulbs and they can give you the step by step instruction to getting the job done if you need more illustration. Good luck and hope this helps and please rate, keep me posted. Be glad to help you get your lights replaced.

Jan 10, 2010 | 1991 GMC Sonoma

1 Answer

Replace rt. front turn signal bulb


look at the other side,under the bumper you just twist and turn and you will have access to change your bulb.

Aug 09, 2009 | 1999 Chevrolet Cavalier

1 Answer

Need to repair front turn signal(upper) how do i access it?


if it is the turn signal in the front bumper all you need is a screw driver to take the whole light piece out, then replace the bulb

Apr 26, 2009 | 1998 Mitsubishi Montero Sport

1 Answer

Signal light bulb change/who and where


  1. From under front wheelhouse, remove access cover behind park and turn signal lamp
  2. Through access hole in wheelhouse, rotate park and turn signal socket counterclockwise one quarter turn.
    1. Pull socket from back of lamp.
    2. Pull bulb from socket. INSTALLATION
      1. Align key on bulb base to groove in socket and insert bulb into socket.
      2. Through access hole in wheelhouse, insert socket into back of lamp.
      3. Rotate park and turn signal socket clockwise one quarter turn.
      4. Install access cover and verify lamp operation.
Hope this helps with your prob

Mar 27, 2009 | 1998 Plymouth Voyager

1 Answer

Signal bulb replacement


you may be able to access the bulb housing under the hood. open the hood and look behind the turn signal for the bulb housing. once located, grasp the housing and turn counterclockwise about a quarter and then pull. be sure to replace wtih the same type/part number bulb.

Sep 25, 2008 | 1996 Mercury Grand Marquis

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...