Question about Ford Crown Victoria

1 Answer

99 crown vic police intersepter car will not run over 20 mph change coil packes and fuel injecters then fuel filter still didnt run right so then i change the cats and mufflers still nothing the only thing i can come up with is the ecm is bad or the fuel pump is going out so any thing i missed

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,101 Answers

Those cars are good for clogged catalytic converters . start the car and place a peice of paper over each tail pipe and see how much exhaust comes out. do not leave to paper there for long it will burn

Posted on Dec 04, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 261 Answers

SOURCE: Ford Crown Vic p0300 random cylinder misfire

take a look at the EGR valve it could be either vacum controlled or electronic either way what seems to be the problem is that the valve is stuck in the open position until the engine warms up you can gently tap the egr valve with a small hammer or a screw driver and you can see that it runs smooth, now if the egr valve is vacum controlled replace the valve. if it is electronoc controlled replace the valve and the module for the egr valve.

Posted on Nov 24, 2008

  • 196 Answers

SOURCE: bad coil pack on crown vic

well if you have checked the spark plugs and they look good then its probly the coil If the plugs have never been replaced i would start with a tune up and see if this fixes the problem. If not there is no good way for you to test it you would need a computer to hook up to the car

Posted on Jan 24, 2009

polarcycle
  • 1392 Answers

SOURCE: 1991 pontiac 2.5 tech 4 fuel pump relay wont energize

Look for a bad fuse or relay. If both check out, most likely an ECM problem

Posted on Mar 07, 2009

  • 1 Answer

SOURCE: where is fuelpump on 2003 crown vic police intercepter

Dear cdkkks,

Replacing a fuel pump in modern cars requires some preliminary electrical, fuel test analysis work. I have noted some professionals indicating you need to run car until gas lines, tank is empty; more than likely, if your fuel pump is defective, you cannot start the car, car is unoperative; you will attempt to start car, starter will turn the engine over rapidly without starting, let's assume you are in this condition.

First we need to test the fuses and fuel pump relay, basically the electrical opportunities on your vehicle, the relay panel is on the fender well, driver side, lift the relay control assembly from the fuse center and press the tab on the end, push down and this will release relays from the cover. This relay control panel includes the PCM power relay (left side in original position) Fuel pump relay (Center) this is the relay you are concerned with and the Air Conditioning relay on (Right). If you have friends, or associates who have electrical equipment to test the fuel pump relay, utilize their help, some automotive shops will provide this service. Checking the relay circuit with a jumper wire, any scrap piece of wire, 16-18 gauge will do; as you are looking directly down at the relay opening, you will note an opening at the 6:00 and 12:00 clock positions, 6:00 is the positive, 12:00 is the neutral, volt meter set for volts will confirm. Open the gas cap from the fuel tank filler pipe, insert the jumper wire and carefully listen for a whirring sound. If there is no sound and you have confirm electrical pump fuses, fuel pump relay is working properly (Voltage is pressure, battery voltage and slightly less voltage at the relay circuit when ignition key is turned on) then we have couple more checks to perform before we replace fuel pump. Let's check the fuel rail pressure on your Ford Crown Vic, obtain a fuel compression gauge with a Ford Schrader valve adapter, check to verify that no fuel pressure exists. If "NO" fuel pressure exists, and we have confirmed the voltage integrity of relay/fuel pump circuit, then we are ready to remove fuel pump. Use a simple gas siphoning kits from your local auto parts outlets to safely remove all remaining gas from gas tank, use appropriate gas tanks to store fuel; safety is the key here, gas and gas fumes are extremely dangerous; use appropriate chemical/gas gloves when siphoning/handling gas.

(A) Park your Crown Vic, perferably in a garage, concrete floor and make sure there is enough room around the back of the vehicle for you to work and move tools around.

(B) Raise the back of your car using a floor jack and support it safely on wheel/jack stands; remember, the driver side rear wheel must be removed in order to remove the fuel tank filler pipe, place your wheel stand (supplement with 2 by material for proper height on frame,slightly forward of rear wheel); safety is the key issue here and I cannot overly emphasize this issue, heavy wheel stands should be supporting the right rear wheel and frame, slightly forward of rear wheel, driver side).

(C) Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle, you must remove the (3) screws on the topside (fuel tank fiiler pipe) and approximately (4) screws on the bottom side, and the (1) screw adapter plate where the fuel tank filler pipe is inserted into the gas tank, top of wheel opening, underneath the vehicle. After these connections are removed, push the fuel tank filler pipe further into the fuel tank, allowing you additional room to lower the filler pipe from it's current position, downward; once you have sufficient clearance, twist, turn left, slightly back and forth movements and carefully pull outward, removing the filler pipe from gas tank. Do not damage the rubber groment in gas tank as you remove the filler pipe. As a note, when you reinstall the filler pipe, insert small amount of vasoline on filler pipe end that is inserted into the gas tank to facilitate the installation process.

(D) Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and slightly lower the fuel tank in order to disconnect the vapor tube from the tee connector on the right and the vapor line from the canister tube. Discard the fuel tank mounting studs and replace with new fuel tank mounting studs on the reinstallation process.

(E) Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

(F) Clean area around the mounting fuel pump mounting flange. Remove/disconnect the fuel lines attached to fuel pump mounting flange then remove the fuel pump mounting flange mounting bolts in a crisscross pattern.

(G) Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to approximately 89 inch lbs using a crisscross pattern. If no torque wrench is available, tighten to a snug fit and stop.

(H) Afterwards, raise the fuel tank enough to attach fuel lines and vapor lines indicated above, item D. After connecting all lines, raise tank with floor jack to its original position "carefully" and utilize the new mounting bolts, securing straps in their original position and torque bolts to approximatlely 25-30 lbs torque.

(I) Install the fuel tank filler pipe per the aforementiond process reversed.

(J) Review your connections and then carefully lower the vehicle, use a gas container, input 4-5 gallows of gas and start the engine and check for leaks.

Wishing you the very best,

drprice

Posted on May 20, 2009

  • 3600 Answers

SOURCE: 1998 crown vic police. Had check engine light with

your egr on that side is dirty try cleaning it aslo check intake boltsaround those clyinders.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to locate spark plugs on 99 crown vic police interceptor engine


They should be mounted down in the cylinder heads, you'll need to remove each coil pack. A long extension and 5/8in spark plug socket and an extendable magnet will help. Also, you may need to remove the fuel rail to get to move the coil packs.

Oct 17, 2010 | 2000 Ford Crown Victoria

1 Answer

I have a '99 Ford Crown Vic Police Interceptor, and its not getting gas to the engine. I replaced the battery, fuel filter, the entire fuel injection assembly, made sure all pumps and wires were plugged...


you will need to change the fuel pump had that problem with one of the customers,if my info is of any help to you please leave me a comment,thankyou.

Sep 02, 2009 | 1988 Ford Crown Victoria

3 Answers

Does the crown vic police intercepter take as much oil as the regular crown vic? (when changing the oil and filter)


I ~think~ the 1999 is the same as the 2000 (mine is a 2000 P71)

The 2000 CVPI (Crown Vic Police Interceptor) owners manual recommends the following:

Engine Oil - Motorcraft SAE 5W-30 Super Premium Motor Oil 5.0 quarts

Transmission Fluid - Motorcraft Mercon V ATF 13.9 quarts (fluids Mercon & Mercon V are NOT INTERCHANGEABLE, DO NOT MIX)

Fuel Tank - 19.0 gallons

Break Fluid - DOT 3


Rear Axle Lubricant - Motorcraft 80W-90 Premium Rear Axle Lubricant 3.75 pints (add 4 oz of Additive Friction Modifier C8AZ-19B546-A or equilavent meeting Ford Spec. EST-M2C118-A for complete refill of Traction-Lok Rear Axles)

Engine Data - 4.6L V8 Engine
Cubic Inches - 281
Required Fuel - 87 Octane
Firing Order - 1-3-7-2-6-5-4-8
Spark Plug Gap - 1.3-1.4 mm (0.052-0.056 inch)
Ignition System - Coil On Plug
Compression Ratio - 10.0:1

I hope this helps!

Jun 27, 2009 | 1999 Ford Crown Victoria

3 Answers

2003 Ford Crown Vic Misfire


usaly plugs & wires but I would get that coil tested before I do wire and spark plugs! if coil is good wire and plugs! hi milage???

Jan 08, 2009 | 2007 Ford Crown Victoria LX Sedan

1 Answer

2005 Crown Vic Police Interceptor: Starts then stalls


Have you checked the fuel filter. Fuel pump will pressure up, but fuel filter could be clogged and not work without the pressure of the fuel pump.

Nov 27, 2008 | 2005 Ford Crown Victoria

2 Answers

Engine light po 300 code


IS THIS A 99 CROWN VIC? IF SO IS IT MISFIRING? IF THIS IS THE CASE YOU MORE THAN LICKLY NEED PLUG WIRES.

Sep 06, 2008 | 1999 Ford Crown Victoria

1 Answer

Engine cuts out , does not throw a code


I also have a 2001 Crown Vic that developed a problem similar to this. It would lope and buck at around 40-45 MPH. I too changed the plugs, then changed the coil boots. It still missed. So I bought 1ea. new coil. After changing the new coil with three old ones, the missing stopped.

Jun 05, 2008 | 2001 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...