Question about 2002 Isuzu Rodeo

1 Answer

Alternator diagram for 2002 Isuzu Rodeo - 2002 Isuzu Rodeo

Posted by Anonymous on

  • Mike Troutman
    Mike Troutman Oct 03, 2014

    Does anyone know the sizes of the bolts that bolt the alternator to the lower bracket and the lower bracket to the block?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Does anyone know the sizes of the bolts that bolt the alternator to the lower bracket and the lower bracket to the block? Someone has put a slip style lower bracket on my trooper as if I would have to adjust the belt tension manually and I am not too keen about that. I have bought a lower bracket but it did not come with the bolts.

Posted on Oct 03, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 84 Answers

SOURCE: replace the alternator on a 97 isuzu rodeo

from Yahoo answers
The alternator is located on the passenger side of the motor at the bottom. There is a bracket attached to the motor and the alternator. You need not take the bracket off to remove the alternator. Two bolts hold the alternator to the bracket. One bolt is on the front top of the alternator and one bolt is located on the bottom front of the alternator. The bottom front bolt is attached to the tension adjustment for the alternator. Loosen the tension screw then remove the bolt going through the tension adjustment. After you loosen the top, front bolt, the alternator should be loose enough to move side to side. Remove the top, front bolt. Now you must disconnect the alternator from the power supply. Behind the alternator is a screw with a wire attached via nut. Remove this wire. Nextly there is a series of wires with a plug on the end. It is plugged into the side of the alternator. Uplug this item. You can also access both of these from the passenger side front tire well. Something to consider is that remanufactured alternators in Rodeo's as well as the Honda Passport (which has the same engine as the Rodeo) do not work and the problem(s) associated with a bad alternator,ie; not charging, no fan blower, battery light and brake light on, still exsist after replacing alternator with reman. Use a factory original alternator if possible. It will cost a little more than a reman but will most likely save you a lot of time and headache!

Hope this helps you out!!
L

Posted on Sep 29, 2008

  • 740 Answers

SOURCE: NEED DRIVE BELT DIAGRAM FOR 2000 ISUZU RODEO

Here is your diagram. Good Luck and say thanks..lol http://www.2carpros.com/car_repair_information/tec_info/2000/isuzu/rodeo/2000_isuzu_rodeo_drive_belt_routing_diagram.htm

Posted on Dec 27, 2008

  • 1 Answer

SOURCE: alternator belt diagram 1992 Isuzu trooper

1. Remove battery terminals and secure them away from the battery posts using nylon wire ties.

1a. Fine some comfortable eye glasses (clear or yellow) and keep them on. There are plenty of opportunities to get debris in your eyes during this procedure.

2. Spray "PB Blaster" (loosens bolts) on two bolts that secures alternator.

3. Jack-up vehicle on side to access alternator. Use a jackstand to support.

4. Using a 10mm open-ended wrench, loosen the bolt that swings the alternator. Screwing the bolt "in" or toward the engine will allow play to increase in the alternator belt. Loosen the 12mm bolt slightly next to the 10mm bolt (approximately 1.5" toward engine).

5. Continue to loosen 10mm bolt until there is enough slack in the belt to remove the belt from the alternator pulley.

6. Remove belt. It may be possible to remove belt without removing fan faring. Maybe not. If not, you will need to remove plastic fairing. If you must remove fair, go below fan fairing and disassemble connectors that hold together pieces of fan fairing. Carefully remove.

7. Install alternator fan from above.

8. Check that alternator belt is on all tracks (from below with a flashlight), and slowly tighten.

9. Secure 10mm and 12mm bolts. Recheck tightness.

10. Reassemble battery connection and run vehicle at idle for about 5 minutes. Check belt for proper tension.

11. CAREFULLY check tension of belt. Or disassemble battery connections and re-check belt tension.

12. Reassemble fan fairing (if not already assembled), re-connect battery terminals, and have a nice day. :-)

Posted on Jan 04, 2009

  • 55 Answers

SOURCE: Serpentine belt installation

moz-screenshot-4.jpg1ca4bfd.gifthere ya go!

Posted on May 02, 2009

  • 125 Answers

SOURCE: How difficult is it to change an alternator on a

easy take the belt off and you have a couple of bolts and an electrical connection to remove

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Isuzu serpentine belt routing diagram for 6VE1, 6VD1, Rodeo, Trooper and Axiom...


Serpentine belt routing diagram for an Isuzu V6 cylinder engine. 6VE1, 6VD1 as fitted to Rodeo, Trooper and Axiom
4b4418d.jpg

  1. Crankshaft pulley
  2. Tensioner
  3. Alternator
  4. Idler pulley
  5. Power steering
  6. Airconditioning compressor
  7. Cooling fan pulley

on Sep 07, 2010 | Isuzu Trooper Cars & Trucks

1 Answer

How to replace a 1995 2.4 v6 isuzu rodeo alternator belt?


Just do a search on google. (1995 2.4 v-6 Isuzu alternator belt diagram) There are plenty of diagrams showing the belt routing. Put the belt on all the pulleys you can. Take a wrench and pull back the tensioner, slip the last part of the belt over the last pulley. Then, release the tensioner arm and it will tighten up the belt. Turn it over and check it again to be sure it is on straight.

Oct 13, 2014 | 1995 Isuzu Rodeo

3 Answers

What is the firing order for isuzu rodeo 2002 2.2 lits


Please don't forget to rate! This helps us help you!!! Thanks!!


c17hydro_180.gif

2.2L VIN D engine Firing order: 1-3-4-2 Distributorless ignition system

May 12, 2011 | 2002 Isuzu Rodeo

1 Answer

Diagram for serpentine belt on 2002 isuzu rodeo


Assuming you have the V6 3.2L engine (no diagram available for the L4 motor), the diagram is below. Thanks for using Fixya!
Greg
greg_margo_1.jpg

Feb 25, 2011 | 2002 Isuzu Rodeo

2 Answers

I can't find the alternator on my 2002 isuzu rodeo.


look at your belts the alternator will be eather on top or bottom of your engin.

Aug 04, 2009 | 2003 Isuzu Rodeo Sport

1 Answer

Serpentine belt installation


there should be a diagram under hood, in front of radiator

May 02, 2009 | 2002 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...