Question about 2002 Toyota Camry
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
I would highly recommend that you go to the local parts store and purchase a Haynes Manual for your vehicle, they are around $ 25.00 Canadian. As when you do your head gasket you wil need to remove your timing belt and this is a procedure in it's self. then you will neen certain torque settings. This manual will provide you with all of this information step by step. they are designed for the do it yourselfer. They also cover many other issues that you may come across through out the ownership of your vehicle. I know that the last ting you need is an added exspence but these manuals are well worth the small investment. There is a site that you can find hrough google search that you can find factory service repair manuals for your vehicle, however they only have a layout for a 4 cylinder engine in there drawings and this is alot different then the 6 cylinder. As the procedure for repairs is totally different. I hope that this helps and that you take the time to rate any solutions you receive. Good Luck.
Posted on Oct 29, 2008
If your sure ALL of your bulbs are good(front and rear)then your bulb check relay is bad its usually in the trunk area,hope it helps have a good dayDB
Posted on Feb 17, 2009
The toyota previa uses a formed silicone gasket for the valve cover and the cover is held in place by metric shoulder bolts ( 10mm). The valve gasket leaks because you can't get enough preload on the bolts to re-seat the old gasket when it gets old and shrinks. The shoulder bolts only allow you to tighten the gasket enough to seat the shoulder on the bolt. If you continue to torque down the suspected bolts, you will snap the bolt off ( don't ask me how I know this ). You can either 1.)replace the old gasket with a new one or 2.) remove the existing bolts around the leak area and put in new metric bolts that do not have a shoulder. You may want to put in a small sleeve into the existing bolt hole but shorter than the thickness of the valve cover to account for the smaller diameter bolt. You can now torque down the bolt and get enough preload to seal the valve cover without removing the old gasket. Make sure you use a torque wrench ( in-lbs) or be very careful not to snap these small valve cover bolts.
Posted on Jul 15, 2009
SOURCE: 1994 toyota pickup blown head
So the first question is ... is it really a blown head gasket? Could also be damaged head, block, etc and the timing chain can wear through it's housing and allow coolant into the oil. If it is a blown head gasket then why did it happen? Is the head warped, coolant passages corroded, or ?? Here's link to
a '93 manual to give you some idea what you're dealing with. http://personal.utulsa.edu/~nathan-buchanan/93fsm/ Can you replace the gasket in shop or driveway ... depends on what sort of
complications you run in to. You may want to have a valve job done while you're there, maybe
time to do the timing chain, etc. Give it a try.
Posted on Dec 02, 2010
Tips for a great answer:
Jan 04, 2013 | 1991 Toyota 4Runner
Nov 03, 2010 | 2002 Mazda 626
Jun 09, 2010 | 1996 Toyota Celica
Jan 09, 2010 | 1994 Toyota Camry
Nov 04, 2009 | 1998 Toyota Camry
Aug 11, 2009 | 2002 Kia Rio
Apr 27, 2009 | 1991 Toyota Previa
Aug 12, 2008 | 2007 Toyota Camry
Jun 21, 2008 | 1999 Cadillac Eldorado
346 people viewed this question
Usually answered in minutes!