Question about Jeep Liberty

1 Answer

I have a 2003 jeep liberty limited edition. The check engine light came on. I took it to have a diagnostic and came back with 2 codes P1294 and P1494

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Jeep Master
  • 1,207 Answers

P1294 Injector High Side Open - Bank 2/Target idle not reached
P1494 SPCUT Solenoid Circuit Malfunction
--------
NEXIQ 125032

Posted on Dec 04, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2002 jeep liberty speed sensor

Jeep Liberty 2002 woahs !
by porth21 - 2/1/09 7:35 AM In reply to: Jeep Liberty 2002 speedometer not working by Dannywon
I have a 2002 Jeep Liberty Limited with the same problem. The main problem I have found to be the routing of the speed sensor wires located on the rear difrential. They are 2 blue wires on my jeep and probably the same on yours. The problem is that they rub on the E-brake cable and once the wire is exposed they short and the speedometer and any other options running off they speed sensor quit working and that includes the tranny shift points and can cause the torque converter to not unlock and cause stalls. I am having the same problem for the third time and chrysler and jeep are both aware of the problem and unwilling to repair the problem or post a recall.

Posted on Apr 01, 2010

Mustgo
  • 2359 Answers

SOURCE: 2005 DIAGNOSTIC ERROR CODE P0069, CRD ENGINE WONT

Are you traveling high ground like Rocky Mountain?

I will remove the ground cable for 4 minutes to reset all data in ECU.///clock and radio stations too : (

Let the ECU to relearn the local environment parameter.



Here's so info on how to prevent vapor lock

Ride with full tank of gas but NO TOP OFF.

Crack open gas cap carefully during rest stops to release / equalize gas tank pressure'

http://www.estes-park-information.com/vapor-lock.html


Good Luck

Posted on Jul 15, 2009

  • 1 Answer

SOURCE: 2005 Jeep Grand Cherokee Limited, 5.7L V8, starter

Every morning at lunch time and evening my jeep won't start. It doesn't grind but the electrical goes crazy. After a couple of trys it finally starts. Help

Posted on Aug 20, 2009

  • 327 Answers

SOURCE: 1999 Jeep Grand Cherokee.....My check engine light

Answer
Hi ,
The code refers to the leak detection pump that is part of the gasoline vapor control system which is for pollution minimization. It says either that the pump switch or mechanical operation is faulty. According to a Chrysler manual I have, you would find the pump, probably on the underside of the vehicle by tracing the hoses related to the vapor recovery tank that may be in the right front corner of the engine compartment (I don't know Jeep designs) and then check to see if the pump starts when you turn the ignition to the run position when the vehicle is cold. Then remove the vacuum hose side of the pump and see if it draws a vacuum. If it does, then the vacuum-detecting switch that detects that the pump operation is OK may be faulty. If the pump doesn't start or doesn't draw a vacuum then the power to the pump, the pump itself, or the vacuum line may be leaky. Finally, the powertrain controller could be at fault.
In any case, that is where the issue is, and it should not be a major issue if it is handled by a knowledgeable mechanic. But you could check it over yourself if you are so inclined. p.s. your best bet is to take it to a jeep dealer to get it fixed hope this helps please dont forget to rate my solution

Posted on Sep 30, 2010

ZJLimited
  • 17970 Answers

SOURCE: Check engine light is on

First off, a model year 2001, its possible still covered under the 5 year/50,000 mile emissions warranty. That's federal law. So you should not have had to pay a penny for that repair since the Leak Detection Pump is an emission control device.

As is the Charcoal Canister. If that is bad there should be no charge for repair or replacement. I hope you saved the receipts because I think they owe you a bunch of money. If they give you an argument about it, call Chrysler and they will take care of it.

Now, are you ready to learn more about the Leak Detection Pump then you will ever need to know? Good! Here it is!

Leak Detection Pump (LDP) Operation And Diagnosis:
* P0442-Evap Leak Monitor 0.040" Leak Detected
* P0455-Evap Leak Monitor Large Leak Detected
* P0456-Evap Leak Monitor 0.020" Leak Detected
* P1486-Evap Leak Monitor Pinched Hose Found
* P1494-Leak Detection Pump SW Or Mechanical Fault
* P1495-Leak Detection Pump Solenoid Circuit

Introduction:
The evaporative emission system is designed to prevent the escape of fuel vapors from the fuel system. Leaks in the system, even small ones, can allow fuel vapors to escape into the atmosphere.

Government regulations (remember I said that?) require on-board testing to make sure that the evaporative (EVAP) system is functioning properly. The leak detection system tests for EVAP system leaks and blockage. It also performs self-diagnostics.

During self-diagnostics, the Powertrain Control Module (PCM) first checks the Leak Detection Pump (LDP) for electrical and mechanical faults. If the first checks pass, the PCM then uses the LDP to seal the vent valve and pump air into the system to pressurize it.

If a leak is present, the PCM will continue pumping the LDP to replace the air that leaks out. The PCM determines the size of the leak based on how fast/long it must pump the LDP as it tries to maintain pressure in the system.

EVAP Leak Detection System Components:
Service Port: Used with special tools like the Miller Evaporative Emissions Leak Detector (EELD) to test for leaks in the system.

EVAP Purge Solenoid: The PCM uses the EVAP purge solenoid to control purging of excess fuel vapors stored in the EVAP canister. It remains closed during leak testing to prevent loss of pressure.

EVAP Canister The EVAP canister stores fuel vapors from the fuel tank for purging. EVAP Purge Orifice: Limits purge volume.

EVAP System Air Filter: Provides air to the LDP for pressurizing the system. It filters out dirt while allowing a vent to atmosphere for the EVAP system.

Leak Detection Pump (LDP) Components:
The main purpose of the LDP is to pressurize the fuel system for leak checking. It closes the EVAP system vent to atmospheric pressure so the system can be pressurized for leak testing. The diaphragm is powered by engine vacuum. It pumps air into the EVAP system to develop a pressure of about 7.5' H20(1/4) psi. A reed switch in the LDP allows the PCM to monitor the position of the LDP diaphragm. The PCM uses the reed switch input to monitor how fast the LDP is pumping air into the EVAP system. This allows detection of leaks and blockage.

The LDP assembly consists of several parts. The solenoid is controlled by the PCM, and it connects the upper pump cavity to either engine vacuum or atmospheric pressure. A vent valve closes the EVAP system to atmosphere, sealing the system during leak testing. The pump section of the LDP consists of a diaphragm that moves up and down to bring air in through the air filter and inlet check valve, and pump it out through an outlet check valve into the EVAP system.

The diaphragm is pulled up by engine vacuum, and pushed down by spring pressure, as the LDP solenoid turns on and off. The LDP also has a magnetic reed switch to signal diaphragm position to the PCM. When the diaphragm is down, the switch is closed, which sends a 12 V (system voltage) signal to the PCM. When the diaphragm is up, the switch is open, and there is no voltage sent to the PCM. This allows the PCM to monitor LDP pumping action as it turns the LDP solenoid on and off.

LDP At Rest (Not Powered):
When the LDP is at rest (no electrical/vacuum) the diaphragm is allowed to drop down if the internal (EVAP system) pressure is not greater than the return spring. The LDP solenoid blocks the engine vacuum port and opens the atmospheric pressure port connected through the EVAP system air filter. The vent valve is held open by the diaphragm. This allows the canister to see atmospheric pressure.

Diaphragm Upward Movement:
When the PCM energizes the LDP solenoid, the solenoid blocks the atmospheric port leading through the EVAP air filter and at the same time opens the engine vacuum port to the pump cavity above the diaphragm. The diaphragm moves upward when vacuum above the diaphragm exceeds spring force. This upward movement closes the vent valve. It also causes low pressure below the diaphragm, unseating the inlet check valve and allowing air in from the EVAP air filter. When the diaphragm completes its upward movement, the LDP reed switch turns from closed to open.

Diaphragm Downward Movement:
based on reed switch input, the PCM de-energizes the LDP solenoid, causing it to block the vacuum port, and open the atmospheric port. This connects the upper pump cavity to atmosphere through the EVAP air filter. The spring is now able to push the diaphragm down. The downward movement of the diaphragm closes the inlet check valve and opens the outlet check valve pumping air into the evaporative system. The LDP reed switch turns from open to closed, allowing the PGM to monitor LDP pumping (diaphragm up/down) activity. During the pumping mode, the diaphragm will not move down far enough to open the vent valve.

The pumping cycle is repeated as the solenoid is turned on and off. When the evaporative system begins to pressurize, the pressure on the bottom of the diaphragm will begin to oppose the spring pressure, slowing the pumping action. The PCM watches the time from when the solenoid is de-energized, until the diaphragm drops down far enough for the reed switch to change from opened to closed. If the reed switch changes too quickly, a leak may be indicated. The longer it takes the reed switch to change state, the tighter the evaporative system is sealed. If the system pressurizes too quickly, a restriction somewhere in the EVAP system may be indicated.

Pumping Action:
During portions of this test, the PCM uses the reed switch to monitor diaphragm movement. The solenoid is only turned on by the PCM after the reed switch changes from open to closed, indicating that the diaphragm has moved down. At other times during the test, the PCM will rapidly cycle the LDP solenoid on and off to quickly pressurize the system. During rapid cycling, the diaphragm will not move enough to change the reed switch state. In the state of rapid cycling, the PCM will use a fixed time interval to cycle the solenoid.
The Charcoal Canister

EVAP/Purge Solenoid:
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.

During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.

The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second , depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.

Vapor Canister:
A maintenance free, EVAP canister is used on all vehicles. The EVAP canister is filled with granules of an activated carbon mixture. Fuel vapors entering the EVAP canister are absorbed by the charcoal granules.

Fuel tank pressure vents into the EVAP canister. Fuel vapors are temporarily held in the canister until they can be drawn into the intake manifold. The duty cycle EVAP canister purge solenoid allows the EVAP canister to be purged at predetermined times and at certain engine operating conditions.

Hope this helps.

Posted on Dec 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Luz marcada con el numero cinco?


2003 Jeep Liberty- Reading Engine / Diagnostic Codes ...

? 1:13
https://www.youtube.com/watch?v=pGrPBBzp7wE
Jan 6, 2013 - Uploaded by DeathScouter
2003 Jeep Liberty- Reading Engine / Diagnostic Codes ..... error code will flash 2 times, brief pause, flash 1 time, pause, flash 5times, pause, ...

2005 Jeep Liberty possible cause of P0442 error. - YouTube

? 5:26
https://www.youtube.com/watch?v=2ba-gH0gadg
Dec 21, 2014 - Uploaded by TheBGravit
While replacing a bad fuel pump I believe I found the cause of a P0442 Error code. I was able to repair the ...

Jeep Liberty Questions - Cylinder Misfire code - CarGurus

www.cargurus.com > Questions > Jeep > Liberty

CarGurusMay 27, 2009 - My jeep Liberty 2009 does the same the Dashboard showed a code of cylinder .... i have a jeep liberty 2006 with the # 5 cylinder misfire. i replaced the sparks... I have a 2005 Jeep Liberty 6 cylinder, engine light came on scaned the ... 2002 jeep liberty camshaft posistion sensor error code p0340 5 answers.

Check Engine Light/Misfire Due to Intake Valve Locks ...

repairpal.com > Problems > Jeep > Liberty
Recently got a second hand 2005 Jeep Liberty Sport. Everything worked fine ... #5intake valve seat dropped and held open the intake valve. 2008 Jeep Liberty.

OBD-II Trouble Code: P0305 Cylinder 5 Five Misfire Detected

www.obd-codes.com/p0305


Dec 08, 2015 | 2005 Jeep Liberty

1 Answer

03jeep lbertyrandom missfire cyl 2 4 6check engine light flashing


Check Engine Light/Misfire Due to Intake Valve Locks ...

repairpal.com > Problems > Jeep > Liberty
Jeep Liberty Check Engine Light/Misfire Due to Intake Valve Locks/Valves. ...Misfire cyc 4 and random cyc misfires, changed coil packs and plugs... sounds as if rod ... Light came on again (misfire on cylinder 4) - switched coil from 4 to 2. Light ...

Jeep Liberty Questions - Cylinder Misfire code - CarGurus

www.cargurus.com > Questions > Jeep > Liberty

CarGurusMay 27, 2009 - #4 misfire new plugs and coil pack on #4 light came back on after 300 miles if ... How come it stopped misfiring for 2-3 months, and now is back? ... I have a 2005 Jeep Liberty 6 cylinder, engine light came on scaned the codes ...

Liberty Cylinder Misfire / Computer issue? - JeepForum.com


Nov 28, 2015 | Cars & Trucks

2 Answers

I have a 2003 jeep liberty giving the code P1494


http://autorepair.about.com/library/faqs/bl010h.htm The Jeep should still be covered under the 10 year emissions warranty. Bring it in to the dealer.

Dec 14, 2010 | 2002 Jeep Liberty

1 Answer

I have a 2002 jeep liberty limited 3.7 code p1494 how to fix it and where is it


p1494
Leak detection pump pressure switch or meahanical fault
could be a leak in the evap system.hard to tract down becuse a large leak ishole small as 0.040-inch.

Sep 17, 2010 | 2002 Jeep Liberty

1 Answer

2002 Jeep Liberty P0174 code and mech has changed the o2 sensor


Can't tell you exactly what is wrong but the one thing you said is of concern...Map sensor should not be full of oil. If it is, I'd want to know why. In finding the reason for that, you may also find the reason why you are having a problem.
Jeep uses two kinds of engine crank venting. you either have a pcv valve or an orifice controlled system. If either are obstructed it can overpressure the crankcase and cause all kinds of problems.
Years of experience tells me this isn't something I can guess at and be 100% sure I have the right answer but based on what you said, I'd look there first!

Feb 07, 2010 | 2002 Jeep Liberty

6 Answers

2002 jeep liberty speed sensor


Jeep Liberty 2002 woahs !
by porth21 - 2/1/09 7:35 AM In reply to: Jeep Liberty 2002 speedometer not working by Dannywon
I have a 2002 Jeep Liberty Limited with the same problem. The main problem I have found to be the routing of the speed sensor wires located on the rear difrential. They are 2 blue wires on my jeep and probably the same on yours. The problem is that they rub on the E-brake cable and once the wire is exposed they short and the speedometer and any other options running off they speed sensor quit working and that includes the tranny shift points and can cause the torque converter to not unlock and cause stalls. I am having the same problem for the third time and chrysler and jeep are both aware of the problem and unwilling to repair the problem or post a recall.

Aug 06, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

471 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...