Question about 2001 Ford Excursion

Open Question

2000 ford excursion service engine soon light

Hhhhg

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2000 ford excursion v10 stall

Had the same problem, did all the checks, alt and battery, found alt bad, changed alt and have not had any issues since.

Posted on Oct 20, 2008

Ad
chuck943
  • 783 Answers

SOURCE: Ford drivers side heated seat doesn't work any ideas?

Most likely one of the heater elements in either the seat cushion or seat back is open.It leaves the module and goes to the seat back on the YE/LB wire thru the seat back and leaves there on the GY/LB wire and goes to the seat cushion and leaves there on the VT/LB. An open in either one of these will cause it not to work.Usally its the seat cushion one that goes bad.
You can test them with an ohm meter and you can get the heated element seperate. Just have to remove the cover to replace it.

Posted on Feb 17, 2009

  • 135 Answers

SOURCE: i need to reset service engine soon light. How do i do this?

you have to have a code reader or you can take to your local parts store(autozone) and they will scan and clear for free

Posted on May 02, 2009

  • 4 Answers

SOURCE: reset service engine soon light 2004 ford mustang

It is not recomended to disconnect the battery and turn the light switch or horn or anything else on in order to clear codes stored in memory because any settings stored in the computer may be lost too.Go to autozone and rent the scanner to do it yourself.It is very easy,just connect the scanner to the connector located below the dashboard, turn the ignition on but not the engine and follow the prompts then when it says: clear codes?hit yes or enter and that is it.This is the safest way to do it.

Posted on May 26, 2009

  • 1 Answer

SOURCE: how to change fuel filter 2000 excursion

Yes it is the tool for fuel lines and ac lines. Your local autoparts store should have them, they are universal. You need to use the small end for the fuel filter.

Posted on Jun 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hose in the rear of the Ford Excursion broke loose after a tire blew, and now there is no water in the radiator and the service engine light came on


Does it have a rear a/c. If it does u Broken the heater core in the rear of the truck. Needs to be repaired and filled with coolant before driving or u can cause damage to engine

Sep 19, 2013 | 2000 Ford Excursion

1 Answer

Whats the fuel pressure on a ford excursion v10


Fuel pressure for your 2000 Excursion is 35-45psi with key on and engine off, with engine running the fuel pressure should be 28-45psi

Oct 14, 2012 | 2000 Ford Excursion

1 Answer

2000 Ford Excursion signal lights and hazard lights do not work?


There is a turn signal/flasher relay that has probably died. They are usually plugged into the cars fuse box. Get a new one from a dealer - they are cheap enough.

Dec 18, 2011 | 2000 Ford Excursion

1 Answer

I just got a full diagnostic check at the Ford dealership, but on the way home my check engine soon light came on. Excursion 2001. What cann the problem be?


Need to scanned the PCM to know exacvtly what fault code is stored there? With this code number could send additional details.

Keep in touch.

Apr 11, 2011 | 2001 Ford Excursion

1 Answer

2000 ford excursion will not stay on


Check the fuel pressure regulator.
by starting the car with your foot on the accelerator pedal half the way if it starts and continue running while you are holdining yore foot on and stops as soon as you take it off the accelerator .
then change the fuel pressure regulator it is located under hood in the rear side at top of the engine.

Jul 20, 2010 | 2000 Ford Excursion

2 Answers

I have a 2000 Ford Excursion. I went to hook up a


If these lights still work on your excursion then it is probably not a fuse problem. It sounds like it is a loose pin(s) with the trailer plug or a loose electrical connection(s) on the trailer or maybe the bulbs on the trailer are burned out. This should help, if not then contact me again at FixYa and I will be glad to help.

Jun 20, 2010 | 2000 Ford Excursion

1 Answer

2000 Ford Excursion Diesel has check engine light of P1391


glow plugs preheat the fuel to help the engine start.....when its hot outside its not that bad...the colder it gets the harder it will be to start with bad glowplugs..

Nov 17, 2009 | 2000 Ford Excursion

4 Answers

Excursion won't start. Engine turns over.


Will turn over but will not start

Oct 22, 2009 | 2000 Ford Excursion

1 Answer

Trouble code indicates all four glow plug on the left side bad


The garage should be able to test the glow plugs without removing them. All the need to do is use an ammeter or amp clamp and measure the current drawn by the glow plugs. the glow plugs should draw 16 - 20 amps each. much less than that and they want replacing.

Nov 09, 2017 | 2000 Ford Excursion

Not finding what you are looking for?
2001 Ford Excursion Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...