Question about Cars & Trucks

Open Question

I am replacing bearings on a toyota hiace diff & wondered if you would have any specs?

Trans./Axle G55 G282

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Toyota Guy
  • 42 Answers

SOURCE: rear axle bearings

There are 4 bolts for each rear axle. They are located behind the rear brake drums. Remove e-brake cable from rear drum and take off brake line.(carefully). I recomend draining and changing your rear differential fluid too, because if the fluid by run out of axle housing. also you should replace the seals for the axles of if you are changing the bearings. When you are done don't forget to bleed your brakes, and hooking up e-brake cable. I hope this answers your question.

Posted on Mar 06, 2009

Ad
  • 14036 Answers

SOURCE: need torque specs for rod bearing caps on 1995 toyota terel 4 cyl

1.6 engine 36 ft lbs 1.8 engine 36 ft lbs 2.0 engine 49 ft lbs

Posted on Apr 11, 2009

canbruce75
  • 1776 Answers

SOURCE: I need the torque spec for the axle and the axle

Go to the autozone.com website and register there. It doesn't cost anything and you will have access to an online repair manual for the vehicle. (Kinda handy) They have a specification section, so the torque specs might be found there. Hope this helps and best wishes.

Posted on Aug 18, 2009

Testimonial: "hey thanks for the help"

  • 599 Answers

SOURCE: torque specs on replacing cv axle on 05 Pacifica

ok here we go tie rod=55 ft lbs axel nut= 180 ft lbs strut bolts= 65 ft lbs plus 90 degrees

Posted on Jan 07, 2010

Testimonial: "thank you very much!!!!!!!!!!"

roniecon
  • 6918 Answers

SOURCE: Replaced rear axle pinion bearing and seal, need

There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diff always a grinding noise and there is end play with the axle 2004 ford ba falcon wagon


When you say end play on the axle, how do you mean? Have you jacked the car in the air and grabbed the wheel top to bottom and side to side and felt for play in the wheel? If you did and it has play, I'd say you're looking at replacing wheel bearings and not a trans (Diff) problem.

Jul 19, 2016 | Cars & Trucks

1 Answer

What are torque specs on 1965 ford 7 and 1/4 inch rear


I have a '68 Motor's manual (goes back to'58) the only rear end specs I can find are for the pinion nut (140 ft. lbs.)
pinion preload: 17-27 in. lbs. w/integral carrier or 22-32 in.lbs. w/ removable carrier. Tightening the carrier bearings isn't so much a torque setting but more or a tightening procedure. Theses specs are done during the rebuild so I wonder if you're asking about the bearing caps or bolts that hold the diff. to the axle housing? I could not find a spec. for bolt torque. Since the bolts that hold it in (if that is what you asking about) are not a bearing adjustment, you can go with a generic torque based on bolt size. Again, I'm not sure what component, or bolts it is you are asking for torque specs on.

Sep 17, 2014 | Cars & Trucks

1 Answer

REMOVEING DIFFERENTIAL ON A 1999 300M FRONT WHEEL DRIVE


The diff is part of the trans axle automatic transmission assembly and is not a separate part that can be removed.

Oct 10, 2012 | Cars & Trucks

1 Answer

Intermittent backlash in drive train appears to be between transfer case to front diff in 4th gear on bitumen when centre diff lock engaged no more backlash. mainly occurs when at a constant speed ie 70 to...


you shouldnt be in 4 wheel drive on bitumen you will get "bind up" of drive train which can cause damage or excessive freeplay in other components in drive train, inspect freeplay in universal joints on tailshafts, centre bearing and diff backlash specs, some backlash is quite normal, inspect trans/transfer case mounts also.

Jan 22, 2011 | 2001 Toyota Land Cruiser

1 Answer

How hard is it to replace rear end output shaft seals (inner axel seals) 98 town and country? What fluid goes back in?


I assume you mean trans axle seals in front.
You have to remove the drive axles,best done on a lift,not in your driveway.
Trans fluid lubes the Diff,that is in trans.
ATF4 etc,whatever the fluid replaced the original spec, when it was new.

Oct 01, 2010 | 1998 Chrysler Town & Country

1 Answer

How to Replace rear wheel bearing


first remothe the diff cover and drain, find the bolt that retains diff gears and remove then remove pin holding the diff gears, at this point do not rotate any part at all, axle or crown, push axle inward and remove c clip holdin axle in, pull axle out and using a bearing puller remove bearing, lubricate new bearing and install using new seal, examine axle for damage to bearing contact surface is good install , reverse procedure to finnish and fill rear end with new oil

Sep 16, 2010 | 1998 Chevrolet S-10 Pickup

2 Answers

Oil leak by back brake right side coming from axle seal need to replace seal donot no how to remove axle seal


Step 1, DO NOT follow the advice in Soultion #1.
You have to remove the axles to get to the bearing. If it's a C-Clip Dana 35C differential, remove the wheels and brake calipers and the 4 bolts holding the brake backing plate to the axle tube,remove the diff cover, drain the fluid, pull the C-Clip and remove the axle with a slide hammer or with the brake rotor put back on the wheel studs backwards. Dana 35C diffs the wheels bearings will stay in the axel tubes, go to Auto Zone and rent a bearing remover. If its a Dana 35 diff, take the axle to a machine shop and have the bearing pressed off and a new seal installed the have the bearing pressed back on.

Jan 15, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Rear axle bearing lock washer and nut coming loose


You may have incorrect axle end play. The left axle is fitted with a 1mm shim and an o-ring between the bearing housing and diff flange. The right bearing housing should be shimmed to suit specs. If the right axle has too much end play, it may try to walk.

Aug 16, 2009 | 1988 Mitsubishi Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...