Question about Nissan Cars & Trucks

Open Question

How do you remove the ignition lock cylinder on a 199 Nissan Altima

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 99 Answers

SOURCE: how to remove broken key in Ignition switch

If your key is magnetic and it is not jambed in there to much you may be able to get a magnet and pull it out. If it is stuck pretty bad you will have to take the steering column apart, but trying calling a lock smith first, he may be able to help.

Posted on Aug 03, 2009

c17hydro
  • 2984 Answers

SOURCE: cylinder head removal on 2005 nissan altima 2.5

CYLINDER HEAD REMOVAL

2.5L Engines

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain cooling system and engine oil.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose and heater hose
    • Right side fuse/relay box and move aside
    • Engine undercover
    • Resonator and air cleaner case
    • Engine top cover
    • All electrical and vacuum lines at the head
    • Fuse hose quick connector at fuel tube side
    • Engine harness and power steering hose bracket
    • Timing chain
    • Drive belt tensioner
    • Camshafts
    • Spark plugs
    • Exhaust manifold
  5. Support the engine from above and below with a suitable jack and hoist.
  6. Remove or disconnect the following:
    • Power steering pump and reservoir and wire aside
    • Auxiliary drive belts
    • A/C compressor and wire aside
    • Upper sway bar links
    • Front and rear engine mount through bolts
    • Lower ball joints
    • 2 steering gear housing mounting bolts
    • Front suspension member bolts and front suspension member
  7. Loosen the cylinder head bolts in the sequence shown and remove the cylinder head.
d365038.gif
Removing the front suspension member—Altima

7555308.gif
Cylinder head bolt removal sequence—2.5L engine–Altima and Sentra

1e6ce81.gif
Cylinder head bolt tightening sequence—2.5L engine–Altima and Sentra

To install:
  1. Clean the gasket surfaces.
  2. Using new head gaskets, install the cylinder heads.
    NOTE If possible, replacement of the head bolts is suggested.

  3. If replacement of the head bolts is not possible, perform the following bolt measurement:
    • Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    • Measure the diameter of the head bolt 2.17 in. (55mm) from the bottom of the bolt.
    • Whenever the size difference between the 2 measurements exceeds 0.0091 in. (0.23mm) the head bolts must be replaced.
  4. Apply clean engine oil to the bolt threads and seating surfaces and tighten the cylinder head bolts in sequence as follows:
    • Step 1: 72 ft. lbs. (98 Nm).
    • Step 2: Loosen all the bolts completely.
    • Step 2: 29 ft. lbs. (33 Nm).
    • Step 4: Plus 75–80 degrees clockwise.
    • Step 5: Plus 75–80 degrees clockwise.
  5. Install the front suspension member and tighten the bolts to the specifications shown in the illustration.
  6. Install or connect the following:
    • 2 steering gear housing mounting bolts
    • Lower ball joints
    • Front and rear engine mount through bolts
    • Upper sway bar links
    • A/C compressor
    • Auxiliary drive belts
    • Power steering pump and reservoir
    • Exhaust manifold
    • Spark plugs
    • Camshafts
    • Drive belt tensioner
    • Timing chain
    • Engine harness and power steering hose bracket
    • Fuse hose quick connector at fuel tube side
    • All electrical and vacuum lines at the head
    • Engine top cover
    • Resonator and air cleaner case
    • Engine undercover
    • Right side fuse/relay box and move aside
    • Upper radiator hose and heater hose
    • Negative battery cable
  7. Fill the cooling system and engine oil
  8. Start the vehicle, check for leaks and repair if necessary.

Posted on Nov 13, 2009

  • 14036 Answers

SOURCE: 2003 nissan altima, 4 cylinder 2.0 car turns on

CHECK FOR DISCONNECTED OR BROKE ACCELERATOR LINKAGE OR CABLE.

Posted on Jan 09, 2010

ZJLimited
  • 17970 Answers

SOURCE: 1993 nissan altima code 21 ignition signal - how to fix/repair

Replace the O2 Sensor, reset the ECU, and subject solve.

Good luck.

Posted on Jul 19, 2010

kapishtech
  • 2272 Answers

SOURCE: removing the lock cylinder from

The lock cylinder is secured on to the steering column using two shear-off bolts (their heads shear off after a certain torque is applied while tightening them. So, you can not uncsrew them.).So you will have to drill out the security bolts on either side to remove the lock cylinder easily. Start with a small drill bit and get larger and larger.The lock cylinder will fall off. Check out.Keep updated.Thanks.

Posted on Sep 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I tried to program a new fob for a 1999 Altima. And nothing worked





1.   Close and lock all doors with the driver’s side power lock/unlock switch.

2.   Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode.

3.   Insert key into the ignition cylinder and turn to the ACC position.

4.   Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful.

5.   If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters).

6.   Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.




Make sure you have the right fob for your car.

Nov 15, 2016 | 1999 Nissan Altima

1 Answer

2003 nissan altima key won't turn


Sounds like a problem with your ignition lock cylinder. Have you tried more then 1 key?

Jan 25, 2014 | 1998 Nissan Altima

1 Answer

P1610 and P1614 Keys won't turn for Lock Position on Ignition Lock Cylinder


Not sure what the problem here is.
The codes are for the security system - - the key is not sending a signal or the right signal for the car to start.
Could be a problem with the lock cylinder which may have a sensor for the key inside it.

Jul 02, 2012 | 2002 Nissan Altima

2 Answers

Hi. I recently lost my car key and I'm wondering if I would be able to knock out the ignition switch and start it that way. Is this possible with a 1993 altima?


Only in the movies, I'm afraid. Does one key do everything on this car? I believe it does. If so, remove the lock from the glove box, if it has one, and take it to a locksmith to make you a key. Any easily removable lock cylinder on the car will do also, such as the trunk lock.

Mar 04, 2011 | 1993 Nissan Altima

1 Answer

1995 Nissan Altima Ignition doesn't turn the starter. No electircal draw down.


Sounds like a bad ignition switch. Located behind the key lock cylinder.

Nov 24, 2010 | 1995 Nissan Altima

1 Answer

Hi I want to program a new keyless fob. I have the original fob that works great.Do I need to do anything to the original key when I program the new fob? 2006 nissan altima


1. Close and lock all doors with the driver’s side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.


5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.

Nov 16, 2009 | 2006 Nissan Altima

1 Answer

Key does not come out steering wheel is not locked


if the key will not come out but is turned to the correct position to be removed, then it sounds like it needs an ignition lock cylinder (this cylinder also directly actuates the steering wheel lock

Sep 29, 2009 | 2003 Nissan Altima

2 Answers

How to remove broken key in Ignition switch cylinder Nissan altima


If your key is magnetic and it is not jambed in there to much you may be able to get a magnet and pull it out. If it is stuck pretty bad you will have to take the steering column apart, but trying calling a lock smith first, he may be able to help.

Aug 03, 2009 | 2003 Nissan Altima

2 Answers

Is there a way that I can reprogram a key fob from a 2003 Nissan Altima so that it works on another 2003 Nissan Altima?


yes u can and here is the procedure.
1. Close and lock all doors with the driver’s side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.


5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.

Jun 12, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...