Question about Cars & Trucks

1 Answer

Am installing a new exhausted from manifold back. Have the flange of exhaust up and in place next to manifold. They're not lining up but in order to get them lined up I need roughly an inch to inch.5 .what would be easyier to do drop the cross chassis. Or Jack the motor up to gain the clearence.? Would prefer to just Jack motor slightly but what motor mount to loosen to accomplished this e

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Cars & Trucks Master
  • 2,030 Answers

Take out mounts and carefully jack motor up

Posted on Dec 03, 2012

  • david threet Dec 03, 2012

    Ok its a 01 corolla what motor mount to take out

  • Sean Wright
    Sean Wright Dec 03, 2012

    the front and at least one side maybe both

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 45 Answers

SOURCE: 98 Honda Civic EX Exhaust.

Donut gasket. You need 2 of them.

Posted on Aug 12, 2008

  • 416 Answers

SOURCE: Exhaust pipe/flange detached from the motor.

Depends how close it to motor. If it not to close to motor you can get a connector at Meijer for $9.99 and reattached it by yourself. But it would be just temporary fix. Overwise you need to buy a full assembly.
Hope that helps
Good Luck

Posted on Apr 01, 2009

  • 398 Answers

SOURCE: replace exhaust manifold on 2002 civic LX is it hard to do?

no you can remove it without removing the rad. the gasket is metal reuse it.forgot u must temove the heatshield

Posted on Jul 12, 2009

  • 242 Answers

SOURCE: Exhaust removal required to drop transmission on 92 Ford Ranger?

Yes you do. trust me you don't want to get that thing half way out and down and not be able to continue. Soak those rusted exhaust studs in a good penetrating oil over night. I bet they come right out. I would not recomend cutting the pipe.

Posted on Aug 27, 2009

Suzman
  • 642 Answers

SOURCE: volvo 850 smoke coming from exhaust manifold

Not to worry. Run the engine up to operating temp before jumping to conclusions and let the heat burn off any excess oil. A leaf will not do any damage.Do not let the engine overheat while idling and if the oil light comes on switch off immediately.
The smoke from the exhaust is oil deposited by oily assembly hands just burning off. It should dissipate after about 15 minutes at most.(or 5 miles' drive)

Posted on Jun 07, 2010

Testimonial: "yup kept running it and watching stopped smoking idle eventually smoothed out. only two problems left, bad o2 sensor (knew that before i started), and a high idle, ill worry about the high idle later. :)"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can a coventional exhaust donut be used in place of the oem seal ring between the manifold and exhaust flange. The flange is not flat and when ring is replaced, there is still a slight leak?


A traditional exhaust donut style will not seal on this type of exhaust you either need to clean manifold and exhaust flang better or replace piece that is warped

Oct 02, 2014 | Cars & Trucks

1 Answer

Replace exhaust manifold


which engine.? 8v or 16v.

the manifold unbolts, see the studs there. they are nuts acutally

the trail pipe flange , has.

on the 8v, engine has 3 nuts and washers.

the 16v engine runs a donut ring, and 2 long spring loaded bolts.

that love to seize.

it just unbolts but rust is devil we all deal with.

the 16v has 2 bolt flange on top that holds up the AIR PIPE>. huge.

here is the torque page.

http://www.fixkick.com/specs/torque1.html



the 16v torques work too, on this full fsm under engine.

http://www.acksfaq.com/trackerfsm.htm

read the section on exh, man. they put the torque\'s, in line.



here is a slide show of the 16v.

http://www.fixkick.com/engine/97-motor-pull/HTML/image_58.html



here is both,

http://www.fixkick.com/exhaust/92-95all.pdf

Mar 28, 2014 | 1994 Geo Tracker

1 Answer

Diragram on how to change the water pump on a 1995 z24 cavalier 2.3


Check this procedure, according with the repair guide for...

2.3L and 2.4L Engines
(see Figure 9)
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle.
It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
On the 2.4L engines, DO NOT rotate the flex coupling more than 4° or damage may occur.Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  1. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  2. Carefully lower the vehicle.
  3. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  4. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  5. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.

zjlimited_2033.jpg

Fig. 9: Water pump and cover mounting - 2.3L and 2.4L engines (click over image for zoom)

To install:

  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts-19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly-106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first-19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover-125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  10. On the 2.4L engine, install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  19. Once the vehicle has cooled, recheck the coolant level.

Hope helps; remember to rating this answer and leave a testimonial comment. Thank you for using FixYa.

Oct 13, 2011 | 1995 Chevrolet Cavalier

1 Answer

What is the torque setting for 1999 ford 182 exaust manifold


Check this for 1996-1999 FORD 3.0L (182) V6 DOHC...
- Install the exhaust manifold with a new exhaust manifold gasket.
- Install the exhaust manifold retaining studs and tighten to 13-16 ft. lbs. (18-22 Nm) in the sequence illustrated.
Raise and safely support the vehicle.
Position the Y-pipe assembly using a new flange gasket and install all the retaining nuts and bolts loosely.
Starting at the front of the system tighten the Y-pipe to exhaust manifold nuts to 26-34 ft. lbs. (34-46 Nm).

- Tighten the converter to transaxle nut and bolt to 30 ft. lbs. (40.3 Nm). Tighten the converter outlet bolts to 26-34 ft. lbs. (34-46 Nm).

zjlimited_1988.jpg

Fig. Right side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click image for zoom)


zjlimited_1989.jpg

Fig. Left side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click over image for zoom)

Hope this helps (remember to rating this answer).

Oct 06, 2011 | 1999 Ford Taurus

2 Answers

How to replace water pump on 97 pontiac sunfire 2.4


PLEASE DON'T FORGET TO RATE! THANKS! 2.3L & 2.4L Engines
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle.
It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
On the 2.4L engines, DO NOT rotate the flex coupling more than 4° or damage may occur.
  1. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  2. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  3. Carefully lower the vehicle.
  4. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  5. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  6. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.

01add58.gif
Water pump and cover mounting-2.3L and 2.4L engines

To install:
  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts-19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly-106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first-19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover-125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  10. On the 2.4L engine, install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  19. Once the vehicle has cooled, recheck the coolant level.

Sep 13, 2010 | Pontiac Sunfire Cars & Trucks

2 Answers

I have an 1998 Chevy Blazer and need to change the catalytic converter, are the flange bolts welded and can i cut them


Catalytic Converter Removal & Installation 2.2L Engine To Remove:
Catalytic converter 2.2L engine gm-03-22-734.gif

  1. Raise and safely support the vehicle.
  2. Disconnect the heated oxygen sensor (HO2S) electrical connector.
  3. Remove the exhaust manifold pipe flange mounting nuts from the catalytic converter.
  4. Remove the catalytic converter flange mounting nuts from the muffler.
  5. Remove the catalytic converter from the muffler.
  6. Remove the catalytic converter from the rear hanger bracket insulator.
  7. Remove the catalytic converter.
  8. Remove the (HO2S) from the catalytic converter.
To Install:
  1. Install the (HO2S) to the catalytic converter.
  2. Install a new gasket and the catalytic converter to the muffler.
  3. Install catalytic converter to the catalytic converter hanger.
  4. Install the catalytic converter flange mounting nuts to the muffler flange.
    • Tighten to 26 ft lbs (35 Nm).
  5. Install the catalytic converter flange mounting nuts to the exhaust manifold pipe flange.
    • Tighten to 26 ft lbs (35 Nm).
  6. Connect the heated oxygen sensor (HO2S) electrical connector.
  7. Lower the vehicle.
------ Catalytic Converter Removal & Installation 4.3L Engine To Remove:
  1. Raise and safely support the vehicle.
  2. Raise and support the transmission.
  3. Remove the transmission support
  4. Disconnect the left and right pre-converter heated oxygen sensor (HO2S) electrical connector.
  5. Disconnect the post-converter (HO2S) connector. Muffler flange and gasket gm-03-43-731.gif

  6. Remove the catalytic converter flange mounting nuts from the muffler.
  7. Remove the catalytic converter from the muffler.
  8. Remove the exhaust manifold flange mounting nuts from the catalytic converter. Catalytic converter 4.3L engine gm-03-43-735.gif

  9. Remove the catalytic converter from the support bracket insulator.
  10. Remove the catalytic converter and gaskets.
  11. Remove the heated oxygen sensor.
To Install:
  1. Install the heated oxygen sensors as needed.
  2. Install a new gasket and the Install the catalytic converter to the support bracket insulator.
  3. Install the catalytic converter to the exhaust manifold flange. Install the mounting nuts.
    • Tighten to 39 ft lbs (53 Nm).
  4. Using a new flange gasket, install the catalytic converter to the muffler. Install the mounting nuts.
    • Tighten to 30 ft lbs (40 Nm).
  5. Connect the left and right pre-converter heated oxygen sensor (HO2S) electrical connectors.
  6. Connect the post-converter (HO2S) electrical connector.
  7. Install the transmission support.
  8. Lower the transmission.
  9. Lower the vehicle.
prev.gif next.gif ---
It looks like you can cut them and replace them with new bolts and nuts.prev.gif next.gif

Sep 05, 2010 | 1998 Chevrolet Blazer

1 Answer

Where are the exhaust system bolts located?


Removal & Installation 2.2L Engine To Remove:
  1. Remove or disconnect the following:
    • Negative battery cable.
    • Heat shield.
    • Oxygen sensor.
  2. Raise and safely support the vehicle.
  3. Remove exhaust pipe from the exhaust manifold.
  4. Lower the vehicle.
  5. Remove the exhaust manifold mounting nuts from the cylinder head. chevy_cav_02-04_exmanifold.gif

  6. Remove the exhaust manifold.
  7. Clean the mating surfaces.
  8. Check for cracks, broken flanges and gasket surface damage.
  9. Use a straight edge and a feeler gauge. If the flanges or the mating surfaces do not align, the manifold is warped and should be replaced.
To Install:
NOTE: The manufacturer recommends using new exhaust system nuts.
  1. Install the manifold gasket.
  2. Position the exhaust manifold to the cylinder head. Exhaust manifold 2.2L 87953055.gif

  3. Install the new exhaust manifold nuts. Tighten the nuts starting from the center and working toward the ends to 110 in lbs (12.5 Nm).
  4. Raise and safely support the vehicle.
  5. Install the exhaust pipe to the manifold using a new flex coupler gasket.
  6. Install new exhaust flange mounting nuts.
    • Tighten to 33 ft lbs (45 Nm).
  7. Lower the vehicle.
  8. Install the oxygen sensor.
  9. Install the heat shield.
  10. Connect the negative battery cable.
2.4L Engine To Remove:
  1. Disconnect the negative battery cable
  2. Disconnect the Oxygen (O2) sensor electrical connector.
  3. Remove the (O2) sensor.
  4. Raise and safely support the vehicle. Exhaust brace 2.4L 87953053.gif

  5. Remove the exhaust manifold brace-to-manifold bolt and the oil pan nuts, if necessary. Exhaust heat shield 2.4L 87953051.gif

  6. Remove the upper heat shield. NOTE: Do NOT bend the exhaust flex decoupler more than necessary to remove it. Excessive movement will damage the flex decoupler
    Exhaust flex decoupler 87953056.gif

  7. Remove the manifold-to-exhaust flex decoupler fasteners.
  8. Remove the exhaust pipe.
  9. Carefully lower the vehicle.
  10. Remove the exhaust manifold-to-cylinder head mounting nuts/bolts. Remove the exhaust manifold.
  11. Discard the gaskets and/or seals. Clean the mating surfaces.
To Install:
Exhaust manifold 2.4L 87953055.gif

  1. Install new exhaust manifold gaskets. Position the exhaust manifold on the cylinder head. Tighten the mounting bolts in sequence to 110 in lbs (12.5 Nm).
  2. Raise and safely support the vehicle.
  3. Install the exhaust manifold heat shield. Tighten the mounting bolts to 10 ft. lbs (14 Nm).
  4. Install the exhaust manifold brace-to-manifold bolt and the oil pan nuts. Tighten the mounting bolts to 41 ft lbs (56 Nm) and the nuts to 18 ft lbs (24 Nm).
  5. Position the exhaust pipe to the manifold. Install the manifold-to-flex decoupler mounting bolts. Tighten to 26 ft lbs (35 Nm).
  6. Lower the vehicle.
  7. Coat the threads with a suitable anti-seize compound and install the O2 sensor.
  8. Connect the O2 sensor electrical connector.
  9. Connect the battery ground cable and check for leaks.
prev.gif next.gif

Sep 02, 2010 | 2000 Oldsmobile Alero

1 Answer

How to replace a starter for a 1997 honda passport


Easier done than said! Don't be intimidated by the complexity of this job. You can save hundreds of dollars by doing this simple task in you driveway or garage. This is one of the easier replacements that I have done on a 4WD but there needs to be a little preparation. Exhaust pipe doesn't need to be removed for the 2WD model.
Tools required:
For the removal of the exhaust pipe form the exhaust manifold
17 mm deep well Impact socket
½ in drive 12 in extension for socket and ratchet
½ in drive breaker bad/ratchet w/12 in extension
½ in drive swivel for the socket
For the removal of the exhaust pipe a the flange
Reciprocating saw w/metal cutting blade
For the removal of the starter
Assorted sockets and wrenches for other bolts and nuts
Floor jack and 2 jack stands
Parts needed:
Exhaust Manifold-to-pipe crushable gasket
High Temp caulking for the exhaust pipe flange gasket.
Starter
2 Bolts, nuts and washers for the exhaust pipe flange
Procedure:
Jack the front of the vehicles and place on the jack stands. Take the battery terminal off. Get up under the vehicles and spray WD-40 on the 3 nuts that hold the exhaust pipe on the exhaust manifold and on the 02 sensor that is just below them. Let this sit overnight for breaking purposes. Next day, remove the 02 sensor and using the 17 mm deep well socket, 12 in extension and breaker bar, remove the 3 nuts that were sprayed the night before. This should take about 3 minutes and a little "elbow grease". There is no need in removing the second 02 sensor but it does need to be unplugged at the connector just above it. Next locate the flange about 4 feet aft of the loosened manifold and using the Reciprocating saw, cut the welded on nuts from the back of the flange that is holding the bolts on. Retain the metal gasket for reuse. This should take about 5 minutes. The loose pipe should be free to move a limited space but it will be enough to get the starter out of the hole that it is in. Remove the aluminum shield from below the area where the starter is and remove the 2 bolts holding the starter on. Drop it down where you can remove the cable and small plastic connector next to it. The starter should come out of the confined space that it is in. You will simply go back in reverse order to replace the starter. Ensure that a new gasket is used with the exhaust manifold and 2 good beads of High Temp caulking is used on the rear flange gasket.
I suspect that the different models have varying degrees of difficulty. On 1998 Amigo 2.2, the bottom bolt can only be accessed by somebody with very small hands and the top bolt appears to be inaccessible. Answer #2 (massive pain) does apply to some models.

courtsey of answers.com

Mar 28, 2010 | 1997 Honda Passport

1 Answer

How do I replace the oil pan gasket on a 2001 GMC Yukon XL?


Changing the oil pan gasket on a GMC Yukon XL is realtively simple, but does require removal of the exhaust pipe. You will need a new oil pan gasket and a new exhaust pipe flange gasket.
Put the car on ramps or jacks to access the undercarriage.
Remove the exhaust pipe by removing the 3 nuts holding the exhaust pipe flange to the exhaust manifold. These nuts often rust and prior application of penetrating oil may be required to remove them without damage. Once the pipe is unbolted, work the exhaust system loose from the hanging brackets. In most cases the entire system does not have to be removed since there is enough room to remove the pan with only the front hangers removed.
Drain the oil from the engine
Remove the 10 mm bolts holding the pan to the block.
Remove the old gasket material and scrape any remaining gasket from the block and pan.
Install the new gasket. Forma-Gasket or a similar product may be used in small quantities to "glue" the new gasket in place and prevent shifting while the pan is reattached to the block.
Reinsall the 10 mm bolts in a cross pattern to ensure the gasket is compressed evenly. Do not overtighten the bolts.
Replace the pipe to flange gasket between the exhaust pipe and the exhaust manifold with a new part.
Reattach the exhuast pipe to the hangers.
Install the 3 bolts connecting the pipe flange to the exhaust manifold.
Fill the engine with oil.

Sep 15, 2009 | 2001 GMC Yukon

2 Answers

05 susuki forenza


Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the engine oil from the engine crankcase.
3. Remove the exhaust flex pipe retaining nuts from
the exhaust manifold.
4. Remove the exhaust flex pipe retaining nuts from
the catalytic converter or the connecting pipe.
5. Remove the exhaust flex pipe.
6. Remove the oil pan flange–to–transaxle retaining
bolts.
7. Remove the oil pan retaining bolts.
8. Remove the oil pan from the engine block.
Cleaning Procedure
1. Clean the oil pan sealing surface.
2. Clean the engine block sealing surface.
3. Clean the oil pan retaining bolts.
4. Clean the oil pan attaching bolt holes in the engine
block.
5. Clean the oil pan scraper.
Installation Procedure
1. Coat the new oil pan gasket with sealant.
Important : Install the oil pan within 5 minutes after applying
the liquid gasket to the oil pan.
2. Install the oil pan to the engine block.
3. Install the oil pan retaining bolts.
Tighten
Tighten the oil pan retaining bolts to 10 NSm (89 lb–in).
4. Install the oil pan flange–to–transaxle retaining
bolts.
Tighten
Tighten the oil pan flange–to–transaxle bolts to 40
NSm (30 lb–ft).
5. Install the exhaust flex pipe.
6. Install the exhaust flex pipe retaining nuts to the
exhaust manifold.
Tighten
Tighten the exhaust flex pipe–to–exhaust manifold
retaining nuts to 35 NSm (26 lb–ft).
7. Install the exhaust flex pipe retaining nuts to the
catalytic converter or the connecting pipe.
Tighten
Tighten the exhaust flex pipe–to–catalytic converter
or connecting pipe retaining nuts to 35 NSm (26 lb–ft).
8. Connect the negative battery cable.
9. Install the oil pan drain plug.
Tighten
Tighten the oil pan drain plug to 35 NSm (26 lb–ft).
10. Refill the engine crankcase with engine oil.

Jun 14, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...