Question about Mitsubishi Cars & Trucks

Open Question

Were is located the camshaft position sensor on a mitsubishi eclipse 2001 3.0 V6

Were is located the camshaft position sensor on a mitsubishi eclipse spyder 2001 3.0 V6 manual

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Big Poppa Ma
  • 302 Answers

SOURCE: 2002 Eclipse

its by your intake manifold on the bottom of the engine block. there is a heat shield covering it which will need to be removed to get to it

Posted on Dec 06, 2008

Ad
  • 1 Answer

SOURCE: Changing the front speaker 2001 Eclipse Spyder

There are 7 screws all together to remove the door pannel. First, you have to take off the hanlde for the door. the 2 plastic covers on the handle pop off revealing 2 screws on the top and bottom, remove those. then behind the the door handle on the inside, pull it as if you were to open it and there is a screw that you have to remove. Then there are 2 screws on either side of the door pannel, both are farily close to the top, remove those, and then its just a matter of popping the pannel off. start from the bottom, pop it off then slide it up. becarefull, after the door panel is free, there is a connection for the power doors and windows unhook that then the pannel will be free. after that the speaker will be right there and its common sense on removing that. good luck.

Posted on Apr 02, 2009

  • 1 Answer

SOURCE: location of 02 sensor bank 1 sensor 1 on 3 ltr engine

it's right adjacent to the cataytic converter

Posted on Jun 11, 2009

  • 1 Answer

SOURCE: location 02 sensor Bank1 sensor2 on 2001

in the exhaust , behind the catalytic converter.
autodoc

Posted on Jul 13, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where isa the crank shaft position sensor located on a 2000 V6 Eclipse?


0996b43f8020334f.jpgAuston, I couldn't load both at the same time go to auto zone sign is (it free) and look it up

Sep 10, 2014 | 2000 Mitsubishi Eclipse

1 Answer

Location for camshaft position sensor on 2.4 2005 eclipse


Remove air flow duct away from engine enough to look under it.. Cam sensor is located there.. Held on by one 10 mm bolt and clip. should be red wire, green with yellow stripe and a black one if my memory serves me right.. I have same car different year same engine.. I hope this helps you. please rate my answer thank you

Feb 21, 2013 | 2005 Mitsubishi Eclipse

1 Answer

Replacing crankshaft position sensor 2001 mitsubishi eclipse 2.4l


Access to the crankshaft sensor is impeded by the timing belt, which must be removed, on a 2001 Mitsubishi Eclipse 3.0L V6. -----------------------------------------------------------------------------------
Multidiag Actia

Jan 31, 2013 | Cars & Trucks

1 Answer

How do i replace a camshaft sensor in a 2001 grand am gt 3.4L V6. wher is it located? how long would it take a mechanic?


Disconnect negative battery cable. Remove power ste
ering pump. Remove camshaft position sensor mountin
g
bolt and remove camshaft position sensor. To instal
l, reverse removal procedure. Tighten camshaft posi
tion
sensor bolt to specification.

Jun 25, 2010 | 2001 Pontiac Grand Am SE

1 Answer

Change a crankshaft position sensor on a 2000 eclipse


Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

2002-2004 Mitsubishi Eclipse Camshaft Position Sensor Location?


would this sensor make the car not start when it is hot?

Apr 22, 2009 | 1996 Mitsubishi Eclipse

1 Answer

Were is the Camshaft sensor in the engine?


its near the crankshaft pulley. under the timing cover.

Mar 06, 2009 | 2002 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...