Question about Kia Sorento

Open Question

Kia rio oil pan bolt torque - Sorento Kia Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 271 Answers

SOURCE: Valve cover and Oil pan bolt torque

Inside to outside for torque pattern, 7 foot lbs. or 144 inch lbs.

Posted on Oct 24, 2008

Ad
  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • 176 Answers

SOURCE: My oil drain plug was stripped from the engine oil

Tighten three oil pan/transmission bolts 45 Nm (33 ft. lbs.) Tighten all bolts oil pan/engine block cross over 15 Nm (11 ft. lbs.)

Posted on Jun 12, 2009

c17hydro
  • 2984 Answers

SOURCE: What is the sequence for the bolts on oil pan, for

For the 2.8L there is no sequence. Torque for the bolts are 105 in.lbs.

For the 3.0L torque is 50 in.lbs. in sequence:




40be0ec.gif

30fedd0.gif
For the 3.3L and the 3.8L, no sequence but torque each bolt to 105 in.lbs.

Please don't forget to rate!

Posted on Jul 12, 2009

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Kia Rondo 2.4 oil pan torque


free.autoserviceand.repair/search/kia-rondo-oil-pan-bolt-torque-specs

Jul 22, 2016 | 2008 Kia Rondo

1 Answer

How to change oil pan gasket on kia rio 2003


drain the oil first , remove the bolts around the oil pan and ease away from bottom of engine block,make sure you clean off the old gasket thoroughly , use some liquid gasket , very small amount if your fitting a ready made gasket to hold it in place ,otherwise use the liquid gasket as per the instructions, change the oil filter as well, refit the drain bolt and refill with oil run for a few minutes recheck level , top up if required and check new gasket for leaks

May 14, 2014 | 2001 Kia Sephia

1 Answer

Need to remove engine


INSTRUCTIONS
First remove the air cleaner assembly and battery, then unplug all the sensors, drain radiator and remove hoses, remove all vacuum lines tie the ac compressor out of the way remove it and the PS pump from the block, then unbolt the exhaust manifold and unbolt the two bolts that secure the oil pan to the exhaust downpipe, remove the starter, then loosten all the bolts securing the oil pan to the transmission, remove the torque converter bolts (if AT) loosten the bolts securing the engine to the transmission, with the engine hoist supporting the engine weight remove the engine mount, if it is an automatic make sure you separate the engine from the torque converter.
It is not really that hard or complicated, just requires patience if you are unfamilar with the procedures it may be helpful for you to review the procedures in a chilton or hanes manual, if none are available check the procedures for a Mazda protege, kia sephia, or a ford escort GT since all these cars and your kia Rio use the Mazda BG designed engine


Read more: http://wiki.answers.com/Q/How_do_you_remove_engine_2002_Kia_Rio#ixzz28LyJkCZX

Oct 04, 2012 | 2006 Kia Rio

1 Answer

I need to find the torque specs for the connecting piston rod? also the sequence and torque for the cylinder head bolts this is for a kia rio 2004 6cyl


22 - 24 ft. lbs. for the rod caps and....
110795143Cylinder Head Tightening Torque and Sequence.

Tighten cylinder head bolts in order shown.
Tightening torque: 36.1 ft. lbs. (49 Nm, 5 kg-m)

Loosen bolts in reverse of order shown.

Retighten cylinder head bolts in order shown.
Tightening torque: 18 ft. lbs. (25 Nm, 2.5 kg-m)

Mark cylinder head bolts for rotational reference.
Rotate cylinder head bolts 90°(1/4 Turn) in order shown.

CAUTION:
  • Do not reuse the old cylinder head bolts.

May 31, 2010 | 2004 Kia Rio

1 Answer

Torque specs for 1.5 kia rio connecting rod


TORQUE SPECIFICATIONS kia rio
Cylinder Head Bolts:
(21.7ft.lb) or (3.0kgf.m) 90?

May 22, 2010 | 2001 Kia Rio

1 Answer

Need a diagram on how to do the torque of head bolts for a 2003 kia rio deul cams


YOU NEED A HAYNES REPAIR MANUAL.IT HAS TORQUE BOLT SEQUENCE AND HEAD BOLTS TORQUE.

Mar 27, 2010 | 2003 Kia Rio

1 Answer

How to remove oil pan on kia sportage 99? thanks,Zak.


Hi Zak:
Kia Sportage 1998-02 Repair Guide
Oil Pan - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable 2 Top intake manifold bracket bolts Front 3 axle housing mounting bolts, 4WD only Left front bushing from the axle housing mount and lower the front axle housing Both gusset plates from the engine Transmission under cover Engine under cover Oil pan mounting bolts and using a scrapper tool separate the oil pan Oil pan Oil strainer assembly Oil baffle 76b1888.jpg


  4. Fig. Exploded view of the oil pan assembly mounting

To install:


f149924.jpg
Fig. Tighten the oil pan bolts in sequence
  1. Clean the engine block, oil pan and baffle pan surfaces of any gasket material.
  2. Apply a continuous bead of Loctite Ultra Blue 587® silicone sealant around the baffle pan.
  3. Install or connect the following:

    Oil baffle. Torque the bolt to 84 inch lbs. (9.5 Nm). Oil strainer. Torque the bolts to 84 inch lbs. (9.5 Nm).
  4. Apply a continuous bead of Loctite Ultra Blue 587® silicone sealant around the oil pan.

    Oil pan. Torque the bolts to 84 inch lbs. (9.5 Nm). Transmission under cover. Torque the bolts to 84 inch lbs. (9.5 Nm). Gusset plates to the engine. Torque the bolts to 33 ft. lbs. (45 Nm). Engine under cover Front axle housing into position. When properly aligned, torque the bolts to 48 ft. lbs. (65 Nm). Intake manifold bracket bolts. Torque the bolts to 34 ft. lbs. (65 Nm). Negative battery cable
  5. Fill the engine with clean oil.
  6. Start the vehicle and check for leaks, repair if necessary.

Hope helps with this (remember rated this) Good luck.

Jan 12, 2010 | 1999 Kia Sportage

1 Answer

Where is the transmission pan on a 2001 Kia Rio?


The pan has 14 bolt holes,you will have to remove,the transmission mount to jack the trans up to access the bolts.

Nov 21, 2009 | 2001 Kia Rio

2 Answers

Torque specs for 2004 kia rio cylinder head replacement


youre going to torque it to 65 ft lbs.. start from the centre out and go diagonally. be sure to replace the head bolts and very lightly oil them before installation.

Nov 09, 2009 | 2004 Kia Rio

1 Answer

How to remove oil pan from 2003 kia spectra


REMOVAL

1. Disconnect negative battery cable.
2. Drain engine oil
3. Remove LH and RH side splash shields.
4. Remove front exhaust pipe.
5. Remove oil pan mounting bolts.
  1. Remove oil pan with screwdriver or suitable tool as shown in figure. Caution:
a) Do not force tools between cylinder block and oil pan because this may damage sealing surfaces. b) Do not damage sealing surfaces when removing old sealant

  1. Remove oil strainer.

Replacement

Caution:
a) If oil pan is reused, remove all foreign material from sealing surfaces of cylinder block and oil pan. b) If bolts are reused, remove old sealant from bolt threads.


  1. Install oil strainer. Tightening torque: 5.8 - 8.7 ft. lbs. (7.8 - 11.8 Nm, 0.8 - 1.2 kg-m)
  2. Apply a continuous bead of silicone sealant to baffle plate along inside of bolt holes on contact surfaces. Caution: The oil pan must be installed no longer than 5 minutes after silicone sealant is applied.
3. Install oil pan. Tightening torque: (A) (B) (C) (D): 5.8 - 8.0 ft. lbs. (7.8 - 10.8 Nm, 0.8 - 1.1 kg-m) (E): 28 - 38 ft. lbs. (38 - 51 Nm, 3.8 - 5.3 kg-m)

4. install front exhaust pipe. Tightening torque: (A): 29.7 - 40.5 ft. lbs. (40.2 - 54.9 Nm, 4.1 - 5.6 kg-m) (B): 51 - 69 ft. lbs. (69 - 94 Nm, 6.9 - 9.4 kg-m) (C): 15.2 - 20.2 ft. lbs. (20.6 - 27.4 Nm, 2.1 - 2.8 kg-m)

5. Install LH and RH side splash shields. Tightening torque: 12 - 18 ft. lbs. (16 - 24 Nm, 1.6 - 2.4 kg-m)
6 . Fill with specified amount and type of engine oil.

GOOD LUCK,I HOPE THIS HELPS...

Jun 04, 2009 | 2003 Kia Spectra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

455 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...