Question about 1988 Plymouth Reliant

Open Question

Removal and ihstalation of new heater core 1988 plymouth reliant k

Need diagram

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: Replacing evaporator core in 1997 plymouth grand voyager!!!!

Hello. My name is Chuck and I owned a radiator and air conditioning repair shop for 20 years. The answer to your question is the whole dash board assembly. You need to remove everything to gain access to the evap core. I'm sorry to be the bearer of bad news .At my shop everybody wanted their a/c fixed but nobody wanted to pay the price and I can't blame them. I charged 800 to 900 bucks complete for this job and the chrysler dealer charged about 1200 plus for the same work. Good luck.

Posted on Dec 17, 2008

  • 124 Answers

SOURCE: Replacing the heater core on a '88 Plymouth Sundance?

Behind the dash. You will have to pull the whole dash assembly. It looks like a little radiator.

Posted on Mar 28, 2009

abauto
  • 353 Answers

SOURCE: Where is the Fuel Pump in my 1988 Plymouth

It is necessary to remove the fuel tank from the vehicle to replace the fuel pump

  1. Using a hammer and a non metallic punch carefully tap lock ring counter clockwise to release pump.
  2. Remove fuel pump and 0-ring seal from tank. Discard old seal and pump inlet filter. Installation
  1. Wipe seal area of tank clean and place a new 0-ring seal in position on pump.
  2. Before installing pump always install a new filter on the end of suction tube.
  3. Position fuel pump in tank with locking ring.
  4. Using a hammer and non metallic punch drive ring around clockwise to lock pump in place. CAUTION: Extreme care should be exercised not to overtighten pump as it could leak.
  5. Install tank.

Posted on Jul 25, 2009

  • 10 Answers

SOURCE: Changing the Fuel Filter on a 1988 Plymouth Reliant

MAKE SURE KEY IS OFF USE A BUCKET AND TAKE OFF LINES TO THE FILTER YOU WILL LEAK SOME THEN REVERCE THE SAME WAY BACK BUT MAKE SURE THE ARROW IS POINTED TOWARD THE ENGINE ON THE FILTER

Posted on Jul 27, 2009

  • 70 Answers

SOURCE: Changing my fuel filter in my 1988 Plymouth

You'll can

But you'll have to plug the line very fast. with the pressure and volume of a full tank it makes that simple job a bit more of a task.

When you remove the rubber line from the nozzle of the fuel filter have a stemming plug or bolt handy to quickly insert to seal the flow from the line coming from the tank.

If you can either drain the tank via manual or electronic siphon or run some of that fuel out. Before taking that on or you're going to spill an yet to be determined amount of fuel.

Posted on Jul 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install a new heater core


Borrow a repair manual from a libarry,

Dec 01, 2012 | 1988 Plymouth Reliant

2 Answers

Plymouth reliant 1988, idles fine, under pressure loses power and spits and sputters like it is not getting enough fuel, and have change the map sensor and also checked to make sure that all fuel is...


you said your getting fuel if you check the fuel pressure and it's okay, you should check your injectors next, if not that get put it on machine for diagnostic test then repair accordingly

Sep 04, 2011 | 1988 Plymouth Reliant

1 Answer

Where is the voltage regulator located on a 1988 plymouth reliant 2.2l


according to autozone.com, The voltage of all 1988-95 alternators is regulated by the Powertrain Control Module (PCM).

So it's part of the PCM and cannot be replaced separately.

Sep 21, 2010 | 1988 Plymouth Reliant

1 Answer

1988 Plymouth Reliant needs to be pulled somewhere...


I think about 10-15 mi less than 30 mph-library sec 629 has more info

Sep 13, 2009 | 1988 Plymouth Reliant

1 Answer

My 1988 Plymouth Reliant needs pulled somwhere....


buy manual and see max mph before trans is affectd

Sep 12, 2009 | 1988 Plymouth Reliant

1 Answer

1988 plymouth reliant shift cable keeps coming loose


Can only give you the british name which wont mean a thing in america .Automatic gear change cable .What i often do to keep old motors running like this till i can get the right parts ,is to use some thin wire and refit the connection then wire it together ,that will work for a while till the wire rusts through ,depending what bit has broke the gearbox or the cable end but if its the cable end then i should imagine its a new cable complete

Aug 29, 2009 | 1988 Plymouth Reliant

1 Answer

Changing the Fuel Filter on a 1988 Plymouth Reliant


MAKE SURE KEY IS OFF USE A BUCKET AND TAKE OFF LINES TO THE FILTER YOU WILL LEAK SOME THEN REVERCE THE SAME WAY BACK BUT MAKE SURE THE ARROW IS POINTED TOWARD THE ENGINE ON THE FILTER

Jul 27, 2009 | 1986 Plymouth Reliant 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7727 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...