Question about 2002 Mitsubishi Eclipse Spyder

1 Answer

Were is located the camshaft position sensor on a mitsubishi eclipse 2001 3.0 V6 manual

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer


On the buttom of oil pan take 1 bolt out and 1 wire off it

Posted on Mar 27, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

danr990
  • 1 Answer

SOURCE: 2002-2004 Mitsubishi Eclipse Camshaft Position Sensor Location?

would this sensor make the car not start when it is hot?

Posted on Jun 05, 2012

dustyboner
  • 331 Answers

SOURCE: 2001 Mitsubishi eclipse failed smog

2.4L
7ee7958.jpg

----------------------------------------------------------------------------------------------

3.0L

5d74b17.jpg

Posted on Dec 11, 2008

  • 151 Answers

SOURCE: Location of camshaft position sensor on 2004

On 1999 and later 2.4L SOHC engines it is located on the left end of the cylinder head (opposite end of the engine from the timing belt)

Posted on Mar 10, 2010

Big Poppa Ma
  • 302 Answers

SOURCE: 2002 Eclipse

its by your intake manifold on the bottom of the engine block. there is a heat shield covering it which will need to be removed to get to it

Posted on Dec 06, 2008

DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where isa the crank shaft position sensor located on a 2000 V6 Eclipse?


0996b43f8020334f.jpgAuston, I couldn't load both at the same time go to auto zone sign is (it free) and look it up

Sep 10, 2014 | 2000 Mitsubishi Eclipse

1 Answer

Location for camshaft position sensor on 2.4 2005 eclipse


Remove air flow duct away from engine enough to look under it.. Cam sensor is located there.. Held on by one 10 mm bolt and clip. should be red wire, green with yellow stripe and a black one if my memory serves me right.. I have same car different year same engine.. I hope this helps you. please rate my answer thank you

Feb 21, 2013 | 2005 Mitsubishi Eclipse

1 Answer

Replacing crankshaft position sensor 2001 mitsubishi eclipse 2.4l


Access to the crankshaft sensor is impeded by the timing belt, which must be removed, on a 2001 Mitsubishi Eclipse 3.0L V6. -----------------------------------------------------------------------------------
Multidiag Actia

Jan 31, 2013 | Cars & Trucks

1 Answer

Having trouble locating the camshaft position sensor located on a 2002 eclipse?


sometimes you have to just keep adjusting over and over and over, till you find an adjustment you like, kind of like adjusting ignition timing without light. http://www.prophecyministry.blogspot.com

Dec 20, 2010 | 2002 Mitsubishi Eclipse

1 Answer

How do i replace a camshaft sensor in a 2001 grand am gt 3.4L V6. wher is it located? how long would it take a mechanic?


Disconnect negative battery cable. Remove power ste
ering pump. Remove camshaft position sensor mountin
g
bolt and remove camshaft position sensor. To instal
l, reverse removal procedure. Tighten camshaft posi
tion
sensor bolt to specification.

Jun 25, 2010 | 2001 Pontiac Grand Am SE

1 Answer

Change a crankshaft position sensor on a 2000 eclipse


Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

2002-2004 Mitsubishi Eclipse Camshaft Position Sensor Location?


would this sensor make the car not start when it is hot?

Apr 22, 2009 | 1996 Mitsubishi Eclipse

1 Answer

Were is the Camshaft sensor in the engine?


its near the crankshaft pulley. under the timing cover.

Mar 06, 2009 | 2002 Mitsubishi Eclipse

Not finding what you are looking for?
2002 Mitsubishi Eclipse Spyder Logo

3,120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...