Question about 2010 Chevrolet Equinox

Open Question

Need to replace the wiper blade on a 2012 chevy eqinox????

Wiper blade on rear window is gone and i need to replace it.. cant find how to do it anywhere. Help

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 55 Answers

SOURCE: 2003 chevrolet venture rear wiper

sounds like a bent wiper arm that holds the blade,,, bent it a little .. make sure blade is on correctly too!!

Posted on Aug 14, 2008

  • 1 Answer

SOURCE: 2005 Chevy Equinox Wiper blade hits edge of window

they are different size wiper blades. I just replaced mine in my 2005 chevy equinox. Passenger side is shorter.

Posted on Feb 23, 2009

  • 11 Answers

SOURCE: remove and replace wiper blade assebly 89 chevy silverado

there is a keeper on the inside of the arm. its easier to get to if you remove the whole arm. lift the wiper arm and near the pivot point there is a little flat bar that sticks out along the arm itself. its about a quarter inch long. pull that out alittle and slide the arm off the peg. makes it easier for me. if you cannot get the wiper off still, destroy it. your replacing it anyway and the arm is pretty sturdy.

Posted on Jun 20, 2009

  • 2418 Answers

SOURCE: Rear wiper wont wipe window.

Check for a bent arm, pos. was bent by scruber.  Or was it on during the wash? it may have been stuck at one point and the wiper motor still turning, and is now out of time. Arm position to motor shaft position. 

Posted on Jul 13, 2009

gladys_neal
  • 334 Answers

SOURCE: My Maxx rear window wiper arm will not rotate when

one temporary repair i have done is to take arm off put 2 pieces of paper on top of pivot push arm back on hard this works for how long i am not sure but it has been 5 months since customer has complained ( afree repair ) good luck!!!! other wise a gm dealer is the other option

Posted on Nov 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOw do I replace the rear wiper blade for 2012 GMC Acadia ?


There's a little tab on the wiper blade. But the auto parts stores like A-zone will do it for you.

Sep 30, 2014 | GMC Acadia Cars & Trucks

1 Answer

2011 equinox rear wiper replacement


I just replaced mine. Lift the rear wiper up as far as it will go. which is not very far. Place your fingers on each end of the wiper and pull down. The blade is held in place by a clip. Gentle pressure will downward toward the window will cause it to disconnect. An extra pair of hands to hold the plastic cover up helps. Note the orientation of the blade when you disconnect it. The replacement blade may have a clip on it which may need to be removed. Place the replacement blade in the same orientation as the one that was removed and clip back in place.

Sep 16, 2012 | 2011 Chevrolet Equinox

1 Answer

How to take off the rear windsheild wiper on a 94 grand cherokee


You will need a 13-inch wiper blade for the rear window. 1 - When removing the wiper blade lift the wiper arm away from the window. ----- 2 - With one hand holding the wiper arm press the small tab on the underside of the wiper blade where it meets the wiper arm. ----- 3 - Slide the wiper blade off of the arm by pulling the center toward the bottom of the arm.----- 4 - Lightly lay the wiper arm on the window.----- 5 - Prepare your new wiper blade by taking the curved part of the plastic clip and line it up with the curve of your wiper arm. ----- 6 - Lift the wiper arm and press it through the center of the wiper blade up and over the plastic clip. 7 - Pull the wiper blade up until it clicks. Place the arm back on the window.

Jan 11, 2012 | 1994 Jeep Grand Cherokee

2 Answers

Replacing 2004 gmc envoy xuv rear wiper blade


Replace the blade and the blade holder. These days everything but the arm gets changed....and gone are the days of just replacing the rubber...

Jul 19, 2011 | 2004 GMC Envoy

1 Answer

How do you replace the rear wiper on a 2009 Scion XD?


You can make use of following procedure to replace rear wiper in ur scion xd.
Pull the rear wiper arm away from the rear window in order to access the wiper blade.

  • Locate the hinge where the blade mechanism meets the wiper arm and squeeze the plastic tabs on the blade in order to release it from its locked position on the arm. In some cases, instead of tabs, there is a small button that must be pressed to release the wiper from the arm.
  • Detach the blade from the arm and slide the old blade out. Insert the new blade into the wiper arm and lock the blade in place.
  • Return the wiper arm to its set position. Before driving, wet the window and test the wiper to make sure it is operating properly.
  • Dec 14, 2010 | 2009 Scion xD

    1 Answer

    HOW TO ADJUST THE WIPER BLADE ON A 96 CHEVEY PICK


    take the arm off and turn it round unitil it is at the position you want it to start from

    Jun 12, 2010 | 1996 Chevrolet C1500

    1 Answer

    How to replace the wiper insert at the back of


    moz-screenshot.jpg
    1. REMOVE RR WIPER BLADE
      1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
      2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

    1. REMOVE REAR WIPER RUBBER
      1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
    f54b10a.gif
    1. INSTALL REAR WIPER RUBBER
      1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
    0dd144d.gif
    b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
    8f40009.gif
    c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

    Sep 12, 2009 | 2005 Toyota Matrix

    2 Answers

    Replace rear wiper on 2005 Murano


    You probably already figured this out, but you have to remove the wiper arm completely in order to replace the wiper blade.

    The blades are an unusual size (somewhere around 14 1/2") and I believe they are only available from a Nissan dealership. They include printed instructions in the box but just in case, this is from the official Nissan service manual:

    88b7c7f.jpg

    moz-screenshot-61.jpg9b7da18.jpg








    Apr 05, 2009 | 2005 Nissan Murano

    1 Answer

    2000 Honda Odyssey rear wiper motor replacement


    You are probably correct in thinking its the wiper motor. You can do this but you will need to remove all the interior trim from the rear hatch first. Get a trim clip removal tool at a parts store...it will work much better than just a flat blade screwdriver. You'll have to remove the trim panels starting in order from the top of the door, then the left rear window side trim, then right rear window side trim, then the grab handle, and finally the main rear hatch trim panel. Once inside, removing and replacing the rear wiper motor is easy. You'll start by lifting the cover on the wiper arm retention nut. Remove this nut to get the wiper arm off, then remove the nut under neath which is the motor shaft mounting nut. Now, back inside to remove the other 3 motor mounting bolts. Don't forget to disconnect the connector for the motor wires. Reverse steps to replace.

    Mar 29, 2009 | 2000 Honda Odyssey

    2 Answers

    2005 Chevy Equinox Wiper blade hits edge of window


    The 23 should work on the drivers side but you will need a 19" on the passenger side.
    Hope this helps and let me know.
    Regards,

    Feb 18, 2009 | 2005 Chevrolet Equinox

    Not finding what you are looking for?
    2010 Chevrolet Equinox Logo

    Related Topics:

    285 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8195 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...