Question about 1989 Mazda 626

Open Question

How to change mazda 626 power steering pump

Steering pump is leaking fluid

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Mazda 626 power steering problem

it is normal to lose your steering, bcos it it being powered by the engine,hence it can go down when the main power source dies (ENGINE)

Posted on Dec 23, 2008

  • 2 Answers

SOURCE: p1652, Power Steering Pressure Switch Circuit

to cancel the check engine light disconnect the battery for 20 seconds and then reconnect it. the light should be out

Posted on May 13, 2009

localwonder
  • 6784 Answers

SOURCE: how do i replace the fuel pump in my 1993 mazda 626 2.5

1. Relieve the fuel pressure and disconnect the negative battery cable.

2. If not already removed, depress the clips on each end of the rear seat cushion and remove the cushion.

3. If not already done, detach the electrical connector from the fuel pump/sending unit.

4. Remove the attaching screws from the fuel pump/sending unit access cover and remove the cover.

5. Disconnect the fuel supply and return hoses from the fuel pump/sending unit.

6. Remove the attaching screws and the fuel pump/sending unit from the fuel tank.

7. Detach the sending unit electrical connector, remove the sending unit attaching nuts and remove the sending unit from the fuel pump assembly.



To install:

1. Attach the sending unit to the fuel pump assembly and install the nuts. attach the sending unit electrical connector.

2. Install the fuel pump/sending unit into the fuel tank with a new gasket and install the mounting screws.

3. Connect the fuel supply and return lines.

4. Install the access cover and the mounting screws.

5. Attach the sending unit electrical connector.

6. Position the rear seat cushion over the floor, making sure to align the retaining pins with the clips. Push down firmly until the two retaining pins are locked into the rear seat retaining clips.

7. Connect the negative battery cable, start the engine and check for proper system operation and for fuel leaks.

Posted on Jun 13, 2009

  • 30 Answers

SOURCE: transmission in 1996 mazda 626 slow to shift high rpm

if its reving high then shifting then your trannys going

Posted on Jun 27, 2009

  • 10 Answers

SOURCE: how do you add power steering fluid at a mazda rx8

Ignore earlier post - the RX-8 has an electric power assisted steering system - there are no hydraulics, and therefore no PAS fluid.

Posted on Sep 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering


Depends on where the leak is.
The pump is around $100 - the hoses are around $30 each, and the rack is around $200.
This is parts only plus labor.

Jul 29, 2012 | 2001 Mazda 626

1 Answer

Clutch pedal goes to floor and will not come up on its own as normal. Clutch does not engage. Cannot shift gears. Happened suddenly with no leading indicators noticed, except a possible change in sounds...


check the fluid level of the clutch resovoir, try bleeding the system out and look for visable leaks.the line you need to look for should go into the side of the transmission, and lead up to a small round resovoir.

Jan 02, 2011 | 1996 Mazda 626

1 Answer

Power stering pump fluid leaking.


FIRST MECHANICS COULD HAVE TIGHTEN LINE TOO TIGHT AND DAMAGED THE SEAL IN LINE FITTING.TAKE CAR BACK TO FIRST DEALER.LET THEM KNOW POWER STEERING IS STILL LEAKING AND THEY DID NOT FIX THE PROBLEM.THEY SHOULD NOT CHARGE YOU ANYTHING JOB SHOULD BE DONE RIGHT THE FIRST TIME.

Apr 29, 2010 | 2003 Mazda Tribute

1 Answer

Squeeking noise when turning wheel of my 2002 mazda 626


  • Check the steering fluid, if you need to add fluid do so and also check the hose of the steering if there is a leak. If the noise is still there after you add a steering fluid then visit a local mechanic to check the pump.

Feb 12, 2010 | 2002 Mazda 626

1 Answer

My 94 mazda 626 lx dumped radiator fluid on the ground i believe that its the water pump but dont know where it is or how to change it


Broken water-pump don't dump water when they are bad. They leak bit-by-bit through their bleed holes. You may have a broken hose. You may test the leaking again with plain water, and while the engine is running open the hood and see where the leak is coming from.
If your water-pump is out, you will have to replace it togethet with the timing-belt. And it would be best to get the Haneys repair manual which is more detailed for this job. The water-pump is bolted to the engine side, protected by black plastic covers.

Nov 18, 2009 | 1994 Mazda 626

1 Answer

How do you replace a serpentine belt on a mazda 626


A 626 has two belts. One drives the power steering and water pump (rear belt in 6 cyl) and other front belt drives the a/c and alternator. On the 4 cyl, the front belt drives the power steering and the a/c, and the rear belt drives the water pump and the alternator. All of these are easy to change.

Jul 04, 2009 | 2003 Mazda Protege

1 Answer

Powersteering


typically no one changes power steering fluid but if you insist you will need an evacuation pump or some kind of suction pump and just **** the reservoir dry and then refill with new oil

Apr 21, 2009 | 1995 Mazda 626

1 Answer

Mazda 626 turbo 1990 power steering cuts out intermittently. Any suggestions? How do you flush and renew power steering fluid?


is your pump belt slipping?  To change the oil you need to remove a hose, drain the fluid and replenish.  However, I have a feeling that you need anew pump or your rack and pinion is binding.  And these are items that need replacement. 

Feb 23, 2009 | 1990 Mazda 626

1 Answer

1991 B2600 D/CAB 4X4


check your power steering fluid level
check the power steering belt tension
check the hosesto see if they are restricting the flow of power steering fluid
try bleeding the systek to see if there is any air in the system
try changing the power steering fluid as it may not be the rite fluid for your car
perhaps you have a defective power steering pump or the seals in it are going

Oct 15, 2008 | Mazda B2600 Cars & Trucks

2 Answers

Mazda 626 power steering problem


if it has fluid in it you might need a new power steering pump

Oct 08, 2008 | 1999 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...